Transcript
EASTWOOD’S SPRAYABLE POLYESTER PRIMER-SURFACER is a 2-component high build sprayable body filler that serves as an excellent base for any paint system. It has excellent filling characteristics and superior adhesion to steel, aluminum, fiberglass, SMC, OE Finishes, Self Etching Primers and body fillers. Its high solids and high build formula allows you to achieve a laser straight surface prior to painting. SURFACE PREPARATION: 1. Surface must be clean and free of wax, grease and debris. Use Eastwood’s PRE Painting Prep to remove all contaminants. 2. Sand/abrade surface A. Body Filler & Putty: Rough sand with 80 grit, then 180-220 and featheredge with 320 grit B. Untreated Steel, Galvanized and Aluminum: Sand with 80-180 grit C. Painted Surfaces: Sand and featheredge using 80, 180 ,220 and finish with 320 grit. 3. Completely final sand surface with 320-400 grit paper and re-clean with PRE Painting Prep
SPRAY GUN & APPLICATION RECOMMENDATIONS: 1.8mm to 2.5mm Fluid Tip Size, 35 to 40 PSI
13523ZPL Sprayable Filler Gallon.indd 1
TM
POLYESTER PRIMER-SURFACER GRAY
60717 40342
CAUTION: CONTENTS MAY CATCH FIRE. CONTENTS MAY BE HARMFUL. MAY IRRITATE EYES, SKIN AND LUNGS. Refer to MSDS before use. Do not swallow. Do not smoke. Do not breathe fumes. Do not get in eyes, on skin or on clothing. Store away from heat including direct sunlight. KEEP OUT OF REACH OF CHILDREN. Use only in a well-ventilated area. Wear a respirator approved by NIOSH/MSHA. Keep away from flames, such as a pilot light, and any object that sparks, such as an electric motor. Wear goggles and rubber gloves. FIRST AID: INGESTION: If swallowed, contact Poison Control Center or Doctor immediately. Do not induce vomiting. Drink 1 to 2 glasses of water. INHALATION: Remove from exposure and into fresh air. EYES: Flush with water for 15 minutes. SKIN: Wash with soap and water. IMPORTANT NOTICE: Buyer (and his successors) and user are responsible for determining whether this product is fit for use or application. EASTWOOD makes no warranty, either express or implied, and specifically excludes any implied warranties or conditions of quality, whether of merchantability, fitness or otherwise. On any claim, irrespective of the legal theory invoked, EASTWOOD’s total liability shall not exceed the purchase price of the product. At its option, EASTWOOD may instead replace or repair the product. In no event shall EASTWOOD be liable for any damage of any type, or for loss. CONTAINS: Styrene (100-42-5), Polyester Resin (Proprietary), Domolite (16389-88-1), Talc (14807-96-6), Barium Sulfate (7727-43-7), Ethyl Acetate (141-78-6), Titanium Dioxide (13463-67-7), Silica Crystalline (14808-60-7), Methanol (67-56-1). VOC: 1.42 lbs/gal, 171 g/l WARNING: This product contains a chemical known to the State of California to cause cancer, or birth defects or other reproductive harm.
6
CAUTION: DO NOT return catalyzed material back into can. To avoid contamination, seal lid tightly after each use. Store in a cool dry place.
Apply two or three medium wet coats as needed. Heavy wet coats should NOT be applied. Dry spray may be removed be for recoating. Allow 90 minutes dry time before sanding at 68°F (20°C). Finish with 220 grit followed by 320-400 grit.
Only in the Event of a Chemical Emergency Involving A Spill, Leaks, Fire, or Exposure Call Chemtrec Toll Free Day or Night: 1-800-424-9300 International Call Collect: (202) 483-7616 Manufactured for The Eastwood Company 263 Shoemaker Road, Pottstown, PA 19464 USA: 1-800-345-1178 Canada: 1-800-820-9042 International: (610) 323-2200 www.eastwood.com © Copyright 2011 Easthill Group, Inc.
CONTOUR
Pot Life: 30 minutes at 68°F (20°C). If needed add 5-10% acetone to extend pot life. Clean equipment with lacquer thinner immediately after use. This product is not meant for use below 60°F (16°C), dry time and performance will be dramatically affected.
Scan for product info
• High-Build With Excellent Filling Capabilities • Easy To Sand With No Shrinkage • Excellent Adhesion To Metals, Fiberglass, and Body Fillers WARNING: FLAMMABLE. IRRITANT. Read all warnings and cautions elsewhere on label.
Made in Canada
0
Label #13523ZPL
Rev. 11/11
MIX: 5% by weight
DRY TIMES AT 68°F (20°C) Flash: 5-10 minutes To Sand: 90 minutes, over self etching primer: 4-6 hours To Topcoat: 90 minutes, over self-etching primer: 4-6 hours Force Dry: Purge 10 minutes, Bake: 30 minutes at 140°F (60°C)
1 US Gallon (3.78 Liters)
13523 ZP
11/17/11 9:33 AM
