Transcript
Slate Mosaic Fire Bowl Models: AD658C, AD658S
Important! Please read and follow ALL instructions before assemAD658C/S OM (7/12)
bling or using this product, particularly the safety statements. Failure to follow instructions and warnings could result in damage to property or serious injury.
READ AND FOLLOW ALL SAFETY STATEMENTS, WARNINGS, ASSEMBLY INSTRUCTIONS AND USE & CARE DIRECTIONS BEFORE ASSEMBLING OR USING THIS PRODUCT.
!
WARNING
!
• Outdoor use only. Never use in enclosed area. Use in unventilated areas will endanger your life. • Do not use this unit on or near combustible surfaces or structures such as wood or composite decks, dry leaves or grass, mulch or vinyl or wood siding, etc. • Use on level, non-combustible surface only. • Keep away from all combustible materials including gasoline and other flammable liquids and vapors. • Never use flammable accelerants, such as: gasoline, alcohol, paint thinners, kerosene, etc. To start a fire. Serious injury or property damage could result. • Screen will become hot when in use! Failure to wear protective gloves may lead to injury. • Keep away from house, garage, balconies, or overhangs. • Avoid using during dry or windy conditions. • Keep out of reach of children. • Do not overfill or use to burn leaves or trash. • Exercise the same care you would with an open fire. • Never leave unit unattended while hot or in use. • Do not attempt to move fire pit while hot or in use. • Completely extinguish fire before leaving. • Ashes can remain hot for a long time after fire is extinguished. Dispose of cold ashes properly.
!
• • • • • • •
WARNING
!
Not for use by children. Do not touch or allow children near fire bowl. Bowl and screen are hot during and after use. Do not use indoors or decking. Never leave fire unattended. Never use gasoline, kerosene or any other explosive fuel. Do not use this unit on wood or composite decking or on any other combustible surfaces such as asphalt, dry grass, leaves, mulch, decorative concrete, etc. • Do not use this unit near heat sensitive or combustible structures or materials such as vinyl, or wood siding. • Contact your local authorities regarding possible burn restrictions before using this product. • Only approved for burning: wood, fire logs, paper, charcoal.
!
IMPORTANT
!
• Wipe off residual manufacturing oils on bowl before first use. • Copper, stainless steel, and painted bowl surfaces will discolor after use. This is normal and expected. • Remove cooled ashes from bottom of bowl after each use. • Steel parts are painted with a durable hi-temp finish, but rusting will occur over time due to heat and moisture exposure. • As with any outdoor grill, seasonal maintenance is required to return painted steel surfaces to original appearance. Remove any surface rust with sandpaper or steel brush and repaint with grill paint suitable for high-temperature surfaces. • Surface rust, corrosion or paint chipping on steel parts is not considered a manufacturing defect. • Store in dry location when not in use for long periods of time.
General Care Instructions • Fire bowl may be cleaned with water and mild detergent. • Mosaic surround may be sealed with exterior tile sealer if desired. • Fire bowl will change colors after use, this is normal and expected. • Do not use abrasive detergents or pads to clean bowl or surround. • As with any outdoor grill, periodic maintenance is required to return painted steel surfaces to original appearance. Remove any rust with sandpaper or steel brush and repaint with grill paint suitable for high-temperature surfaces. Follow paint manufacturer’s instructions. • Seasonal maintenance is required on all steel parts to reduce appearance of rust.
Parts List A
Screen
1
G
Storage Cover
1
B
Fire Bowl
1
I
Screen Lift Tool
1
C
Mosaic Surround
1
H
M6X12mm Phillips Head Bolt
4
D
Leg
4
H1 Phillips
E
Cross Bar
2
H2 3.5mm
F
Log Grate
1
A
F
M6X20mm Head Bolt M6 X
Hex Nut
B C Tools Required for Assembly Phillips Head Screwdriver
Customer Service
E D
Email:
[email protected] Toll Free: (800) 230-6530
9
1
Assembly Instructions
Figure 1
Figure 2
Figure 3
Figure 4
Step 1:
Carefully unpack all parts. Inspect for missing parts or damage.
Step 2:
Interconnect the two (2) Cross Bars (E) and fasten together with one (1) Phillips Head M6X20mm Bolt (H1) and Hex Nut (H2) (Figure 1). Loosely hand tighten hex nut only. Do not completely tighten cross bars.
Step 3:
Loosely connect one end of Cross Bar assembly to one Leg (D) (Fig. 2) with one (1) Phillips Head M6X12mm Bolt (H). Loosely tighten bolt only. Note: Completely tightening bolt may make it difficult to complete Step 4. Repeat step until all four ring legs are in loosely fastened in place completing the stand assembly. Do not tighten hardware.
Step 4:
Once the stand is fully assembled, carefully place the Mosaic Surround (C) tile side down. Align holes of completed leg stand assembly to holes on underside of surround. Loosely attach legs to surround with two (2) Phillips Head M6X20mm Bolt (H1) through each leg (Fig. 3). Once the stand is fully assembled and all hardware is in place, tighten all stand hardware with a Phillips Head Screwdriver. Be careful not to strip the bolts by overtightening.
Step 5:
With help, carefully turn assembled stand surround over (Fig. 4). Place Fire Bowl (B) in center of surround. Place Log Grate (F) in bottom of fire bowl. Place Spark Screen (A) on fire bowl (Fig. 5).
OUTDOOR USE ONLY ON NON-COMBUSTIBLE SURFACE ONLY. READ ALL SAFETY WARNINGS BEFORE USE.
Figure 5
