Clipsal® Color Touch Screen Power Supply

Transcript

® Clipsal Color Touch Screen Power Supply SLC5000CTCPS for Use With Wired C-Bus™ Color Touch Screen Instruction Bulletin Retain for future use. Clipsal® Color Touch Screen Power Supply Instruction Bulletin 63249-420-260A3 10/2008 HAZARD CATEGORIES AND SPECIAL SYMBOLS Read these instructions carefully and look at the equipment to become familiar with the device before trying to install, operate, service, or maintain it. The following special messages may appear throughout this bulletin or on the equipment to warn of potential hazards or to call attention to information that clarifies or simplifies a procedure. The addition of either symbol to a “Danger” or “Warning” safety label indicates that an electrical hazard exists which will result in personal injury if the instructions are not followed. This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death. Danger indicates an immediately hazardous situation which, if not avoided, will result in death or serious injury. Warning indicates a potentially hazardous situation which, if not avoided, can result in death or serious injury. Caution indicates a potentially hazardous situation which, if not avoided, can result in minor or moderate injury. Caution, used without the safety alert symbol, indicates a potentially hazardous situation which, if not avoided, can result in property damage or improper operation. NOTE: Provides additional information to clarify or simplify a procedure. 2 © 2008 Schneider Electric. All Rights Reserved. 63249-420-260A3 10/2008 Clipsal® Color Touch Screen Power Supply Instruction Bulletin PLEASE NOTE Electrical equipment should be installed, operated, serviced, and maintained only by qualified personnel. This document is not intended as an instruction manual for untrained persons. No responsibility is assumed by Square D for any consequences arising out of the use of this manual. Class B FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. © 2008 Schneider Electric. All Rights Reserved. 3 Clipsal® Color Touch Screen Power Supply Instruction Bulletin 63249-420-260A3 10/2008 INTRODUCTION The Color Touch Screen Power Supply (SLC5000CTCPS) provides operating power for the Color Touch Screen (SLC50x0CTC). This instruction bulletin includes installation instructions and specifications for the power supply. Before You Begin Before mounting the Color Touch Screen Power Supply, inspect the device and confirm there are no dents or damage. Verify that the catalog number matches the number on the package label, and that no components are missing from the table below. Table 1: Power Supply Contents List Quantity Component 1 Power supply 1 65.6 ft (20 m) DC output cable 1 Adaptor box 1 AC power supply cable The terminal cover on the adaptor box does not come attached. The terminal cover and three small terminal cover screws are included in a package. All tools and mounting screws used for installation are provided by the user. Refer to the "Power Supply Assembly" figure below. Figure 1: Power Supply Assembly KEY: A. Power Supply unit B. Power Supply DC output cable lead terminated with 4-pin connector (factory installed) C. AC power cable D. Power Supply DC output cable [66 ft (20 m)] terminated one end with 4-pin connector. E. Adaptor box F. Touch Screen lead (factory installed) G. Package with 1 terminal cover and 3 terminal cover screws (not shown) 4 © 2008 Schneider Electric. All Rights Reserved. 63249-420-260A3 10/2008 Clipsal® Color Touch Screen Power Supply Instruction Bulletin SAFETY PRECAUTIONS This section contains important safety precautions that must be followed before attempting to install or maintain electrical equipment. Carefully read and follow the safety precautions below. HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH • Apply appropriate personal protective equipment (PPE) and follow safe electrical work practices. See NFPA 70E. • This equipment must be installed and serviced by qualified electrical personnel. • Turn off all electrical power supplying this equipment before working on or inside the equipment. • Always use a properly rated voltage sensing device to confirm that power is off. • Replace all devices, doors, and covers before turning on power to this equipment. Failure to follow these instructions will result in death or serious injury. SELECTING A LOCATION Mount the Color Touch Screen Power Supply between 3.3 and 65.6 ft (1 and 20 m) from the adaptor box, and within close proximity to a power receptacle. Mount the adaptor box close to the Color Touch Screen and confirm the terminated end of the DC output cable plugs into the DC power input port of the Touch Screen. Refer to the "Power Supply Component Connections" figure for a connection illustration. Also consider the following factors when selecting a location: • Verify adequate ventilation is available for cooling the power supply. • Keep the power supply uncovered. © 2008 Schneider Electric. All Rights Reserved. 5 Clipsal® Color Touch Screen Power Supply Instruction Bulletin 63249-420-260A3 10/2008 INSTALLING THE COLOR TOUCH SCREEN POWER SUPPLY The Color Touch Screen is connected to an adaptor box through a DC cable. The adaptor box is connected to the power supply through a DC output cable that the user cuts to the required length and connects to the adaptor box. Step (1): Overview Refer to the "Power Supply Component Connections" figure below. It illustrates how each component is connected from the power receptacle to the Color Touch Screen. Figure 2: Power Supply Component Connections KEY: A. Power receptacle B. AC power supply plug C. Power supply D. Color Touch Screen (back) E. Power supply DC output cable F. DC output cable (cut to length) G. Adaptor box H. DC output cable (terminated end) I. DC power input port NOTE: If the Color Touch Screen is mounted in a Wall Box, the adaptor box may be placed inside the Wall Box behind the Touch Screen to ensure proper connection of the DC output cable. 6 © 2008 Schneider Electric. All Rights Reserved. 63249-420-260A3 10/2008 Clipsal® Color Touch Screen Power Supply Instruction Bulletin Step (2): Running the DC Output Cable 1. Verify that the adaptor box mounting location is the proper distance from the Touch Screen by running the terminated end of the DC output cable attached to the adaptor box to the Color Touch Screen. 2. Run the AC power supply plug from the power supply's mounting location to the power receptacle to verify adequate cable length. 3. Run the 65.6 ft (20 m) DC output cable from the power supply's mounting location to the adaptor box. Step (3): Preparing the 66 ft (20 m) DC Output Cable Refer to the following figures and sections: • "Power Supply Assembly" figure • "Adaptor Box Components" figure • "Selecting a Location" section 1. Cut the unterminated end of the 66 ft (20 m) DC output cable to remove excess cable length between the adaptor box and the power supply. 2. Remove 2.2 in. (50 mm) of the cable's outer sheath, and strip 0.4 in. (10 mm) of insulation from the ends of the four conductors. Figure 3: Adaptor Box Components KEY: A. Terminal block screws B. Terminal blocks C. DC output cable lead with 7-pin connector (to Touch Screen) © 2008 Schneider Electric. All Rights Reserved. 7 Clipsal® Color Touch Screen Power Supply Instruction Bulletin 63249-420-260A3 10/2008 Step (4): Connecting the DC Output Cable to the Adaptor Box Refer to the figures "Adaptor Box Terminal Blocks" in Step 3 and "Adaptor Box Components and DC Output Cable Terminations". 1. Twist the unshielded ends of the 2 red conductors together to make the red twisted pair. Repeat with the black conductors ends to make the black twisted pair. 2. Loosen the two terminal block screws on each side of the adaptor box with a small flat head screwdriver. 3. Insert each twisted pair of conductor ends into its respective terminal block as labeled on the adaptor box. 4. Tighten the terminal screws securely (recommended torque: 12 lb-inch (1.4 Nm). Do not exceed the recommended torque value. 5. Attach the terminal block access cover. Verify the cable is positioned securely in the cable clamp of the access cover. Tighten the 3 terminal block access cover screws provided. Figure 4: Adaptor Box — DC Output Cable Terminations KEY: A. DC output cable lead with 7-pin connector (to Touch Screen) B. Terminal block screws C. Black conductors (2) = black twisted pair D. Terminal cover E. Terminal cover screws F. To power supply DC output cable connector G. Cable clamp H. Red conductors (2) = red twisted pair 8 © 2008 Schneider Electric. All Rights Reserved. 63249-420-260A3 10/2008 Clipsal® Color Touch Screen Power Supply Instruction Bulletin Step (5): Final Connections and Mounting 1. Connect the DC output cable (cut to length) to the power supply via the 4-pin cable connectors. 2. Connect the terminated end of the DC cable from the adaptor box to the DC Power input port on the back of the Color Touch Screen. Refer to the "Power Supply Component Connections" figure for the DC power input port location on the Touch Screen. 3. Mount the adaptor box and power supply in the selected locations. Mounting screws are to be provided by the user. 4. Connect the AC power supply plug into the power supply, and the other end into a 110 Vac power receptacle. SPECIFICATIONS Table 2: Color Touch Screen Power Supply Specifications Catalog Number SLC5000CTCPS Description Color Touch Screen Power Supply Operating Temperature Range 32 to 140°F (0 to 60°C) Operating Humidity Range 10% to 90% RH (non condensing) Storage Temperature Range -4 to 140°F (-20 to 85°C) Storage Humidity Range 5 to 95% RH (non condensing) Output Cable 65.6 ft (20 m) Input Voltage 100-240Vac, 50-60 Hz AC Current 0.39A at full load (120 V AC supply) Output Voltage 5.6 V DC +/- 2%, 3A load Rated Output Power 28W Typical Efficiency 3.3 ft (1 m) DC output cable: 75% 65.6 ft (20 m) DC output cable: 50% Inrush Current 42 A maximum at 120 V AC (cold start) Isolation Resistance >100 MΩ @ 500 V DC between primary lines, neutral to secondary © 2008 Schneider Electric. All Rights Reserved. 9 Clipsal® Color Touch Screen Power Supply Instruction Bulletin 63249-420-260A3 10/2008 Table 3: Color Touch Screen Power Supply — Dimensions Dimensions for the Switch Mode Power Supply (WxDxH) 6.9 x 3.1 x 1.8 in. (175 x 80 x 45 mm) Dimensions for the Adaptor Box (WxDxH) 5.2 x 2 x 0.4 in. (113 x 50 x 11 mm) Weight for the Switch Mode Power Supply, 4.2 lbs (1.925 kgs) 20m DC Output Cable, Adaptor Box, and AC Power Supply Plug STANDARDS The Color Touch Screen Power Supply complies with the following Standards: Table 4: U.S. and Canadian Product Safety Standards and U.S. FCC Regulations Standards/Regulations 10 Title CSA C22.2 No. 205 Signal Equipment UL60950 Information Technology Equipment - Safety: General Requirements FCC Part 15 Class B Digital Device for Home or Office Use © 2008 Schneider Electric. All Rights Reserved. Clipsal® Color Touch Screen Power Supply Instruction Bulletin SUPPORT AND SERVICE Contact the Square D Customer Information Center for technical support by phone at 1-888-Square D (1-888-778-2733) or e-mail at [email protected]. ® Contact your local Square D service representative or Clipsal certified installer for repairs or service to your network. You may also find helpful information on our web site at www.squaredlightingcontrol.com. Schneider Electric, USA 320 Tech Park Drive La Vergne, TN, 37086 1-888-SquareD (1-888-778-2733) www.squaredlightingcontrol.com Square D, , Clipsal, C-Bus, Saturn and Neo are trademarks or registered trademarks of Schneider Electric and/or its affiliates in the United States and/or other countries. Electrical equipment should be installed, operated, serviced, and maintained only by qualified personnel. No responsibility is assumed by Schneider Electric for any consequences arising out of the use of this material. © 2008 Schneider Electric. All Rights Reserved. 63249-420-260A3 10/2008