Transcript
CM-708R 7” TFT LCD COLOR MONITOR
7 VEHICLE
7” TFT LCD
LANGUAGE
INSTRUCTION MANUAL Thank you for purchasing this product. For proper usages and application, please read this instruction manual thoroughly.
PRINTED IN KOREA
ver. 1.0
CONTENTS
SAFEGUARD INSTRUCTIONS -------------------------------------- 3 FEATURE ----------------------------------------------------------------- 5 BOX CONTENTS ------------------------------------------------------- 5 FUNCTION OF EACH PART ---------------------------------------- 6 FUNCTIONS ------------------------------------------------------------- 8 CHANGING REMOTE CONTROL BATTERY -------------------- 12 CONNECTIONS ------------------------------------------------------- 13 INSTALLATION -------------------------------------------------------- 14 SPECIFICATION ------------------------------------------------------ 15
2
SAFEGUARD INSTRUCTIONS 7” TFT LCD COLOR MONITOR
Please read the “Safety Rules” carefully before using this product. Following the safety rules prevents users from damages related with the misuse of the product. It is very important to follow these safety rules. We state “Caution” and “Warning” to clarify any potential risk for a damage associated with the misuse of the product.
CAUTION
WARNING
This information is for preventing damage or shorten the life time of the products. This information is for preventing bodily harm or even death and use should follow this safety rules.
CAUTION Should install while power off. (After install products, connect DC jack) --- It may cause to electronic shock or malfunction. While stop driving (parking), set the car in motion. --- It may cause battery discharge. Do not use multi socket or extended adaptor. --- It may cause unexpected heating, fire and malfunction. Unplug product when do not use for a long time. --- It may case fire by short circuit due to heating. Do not place near magnet. --- It may cause malfunction and trouble. Do not push a LCD panel. --- It may cause LCD broken. In case of inserting battery, attend to polarity and insert according to direction. --- When wrong inserting, it may cause fire, damage by explsion. The battery for remote controller is not rechargeable and should replace same or similar model. Used battery may cause environmental pollution, so trash it carefully. --- This may cause a malfunction and problem.
3
WARNING Do not put the product in place where sudden temperature increasing and should use on optimum voltage, temperature and humidity --- It may cause to electronic shock or malfunction. Do not get product wet and operate with wet hands. --- It may cause to electronic shock or malfunction. Do not place where interfere with visual field and watch or operate monitor during driving. --- It may cause traffic accident. Keep clean dust on power socket. --- It may cause electronic shock and fire by bad connection. Do not pull cord with a jerk, should catch a plug and pull. Do not use damaged cord. --- It may cause cord malfunction, electronic shock and fire. When clean exterior, power off and wipe with dry cloth. --- Wet cloth may cause a electronic shock. Do not clean exterior with volatility or oily solvent. Neither keep touching rubber and plastic for long time. --- It may cause change of surface, fall of paint, malfunction and fire. Do not place where vibration and shock. --- It may cause throw down and then malfunction and accident. Do not put a pin or needle on the hole or crack in the body. --- In case of inserting them, stop to operate, it may cause electronic shock, fire and malfunction. Do not use in problem condition as like smoking, smell something burn. --- It may cause fire. Stop to use and make inquiries to agency. Do not disassemble, repair and remodeling. --- It may cause malfunction and injury, can not get warranty. --- Make inquiries to agent for repair and checkup.
4
1 FEATURE
7” TFT LCD COLOR MONITOR
• 8bit MICRO controller • TFT LCD with high resolution and low reflection • All functions are displayed on screen (OSD function) • PWM volume control • Mode selection function • Low energy consuming rate • Language Display Selection (KOR-JPN-GER-ENG-SPA-FRE-ITA) • 4 Screen Mode (FULL-WIDE-NORMAL-CINEMA) • Free voltage (From DC 12V to DC 24V) • Dimmer selection function
2 BOX CONTENTS 7” TFT LCD COLOR MONITOR
Monitor
Stand
Monitor Cable
Cigar Cable
Manual
Remote Control
TRG Extension Cable
5
3 FUNCTION OF EACH PART 7” TFT LCD COLOR MONITOR
[ MONITOR ]
6
① S/BY LED
Power or Stand-by status display
② POWER
Power ON/OFF button
③ MODE
CAM1/CAM2/AV selection function
④ MENU
SETUP/PICTURE selection function
⑤ UP/DOWN
SOUND/MENU level control
[ REMOTE CONTROLLER ]
① POWER
Power ON/OFF button
② MODE
Selecting CAM1/CAM2/AV
③ MENU
Selecting MENU and changing functions
④ VOL ◀▶(VOL+-)
Changing volume or MENU level
⑤ CH ▲▼
Moving Up/Down on MENU
⑥ MUTE
Mute mode On/Off
⑦ RECALL
Displaying the current channel and volume level
⑧ AUTO PIC
Adjusting the screen setting
7
4 FUNCTIONS 7” TFT LCD COLOR MONITOR
1 POWER ON
OFF
1) Press [POWER] button to the power. (STAND BY state is OFF) 2) Press [POWER] button again to off the power. (STAND BY state is ON) 2 MODE • It is a function to change video signal. CAM1
1) Press [MODE] button. 2) CAM1/CAM2/AV appears on the screen and it is disappearing 5 seconds after setting. CAM1
CAM2
AV
3 UP/DOWN • Press VOL◀▶(VOL+/-) button on remote control or UP/DOWN button on monitor to adjust volume.
VOLUME 70
VOLUME 30
8
4 MENU • It is a function to select MAIN MENU (SETUP/PICTURE/CAMERA) 1) Press [MENU] button to select MAIN MENU, changed color in red when it is selected.
SETUP
PICTURE
CAMERA
2) Press [MODE] button to select SUB MENU, UP/DOWN button to change SUB MENU.
DIMMER LANGUAGE DIRECTION DISPLAY MARKER RESET
CONTRAST BRIGHTNESS COLOR TINT
ENGLISH 0˚ FULL OFF ▶
70 70 50 50
[ 1. SETUP ] • DIMMER
• LANGUAGE
ENGLISH
DEUTSCH
ITALIANO
ESPAnOL
한국어
日本語
FRANCAIS
• DIRECTION ENGLISH 180˚ FULL OFF ▶ ENGLISH 0˚ FULL OFF ▶
DIMMER LANGUAGE DIRECTION DISPLAY MARKER RESET
DIMMER LANGUAGE DIRECTION DISPLAY MARKER RESET
9
• DISPLAY
WIDE
NORMAL
CINEMA
FULL
• MARKER Warning
- The onscreen distance markers should be considered as a general reference to assist the driver in assessing the distances depicted on the screen. The distance markers have been designed based on the CCD camera installation conditions listed in the next section, but differences in vehicle design and construction may result in the actual installation condition or location being different from the conditions listed. In such cases, the display location should be set at the closest marker No. - Distance markers cannot be set if non CAMOS cameras are used. Caution
- The markers may not indicate the exact position of the bumper, the vehicle s width or the distance to the rear. Use as a reference only. (1) Press MENU button on CAM1, full screen mode. (2) Press MODE button and select MARKER. DIMMER LANGUAGE DIRECTION DISPLAY MARKER RESET
(3) Then, press [DOWN/UP] button on the monitor or [◀▶] button on the remote control, select ON.
ENGLISH 0˚ FULL OFF ▶
* It is set OFF from the factory.
(1) Press MENU button and select MARKER SELECT menu. (2) Press [DOWN/UP] button on the monitor or [◀▶] button on the remote control, and switch marker pattern. * Distance marker function setting is only possible when MARKER is selected on CAM1, full screen mode. ■ CCD camera installation conditions (distance marker input conditions) Vehicle width
MARKER SELECT
(From bumper toward rear) Ｐ１
７ｍ
10
Camera Install Height
Vehicle Width ２，５００
５ｍ
Ｐ１
２，０００
３ｍ
Ｐ２
２，２５０
Ｐ３
２，５００
１ｍ
Bumper position
(Unit：mm) Marker No. (Pattern)
Ｐ４
２，７５０
Ｐ５
３，０００
Ｐ６
３，２５０
Ｐ７
３，５００
２，３００
２，５００
(1) Press MENU button and select MARKER ADJUST menu. (2) Press MODE button and select H / V. (H: horizontal / V: vertical ) (3) Press [DOWN/UP] button on the monitor or [◀▶] button on the remote control, and switch marker pattern. (H = -10~+10, V= -12~+12, Default setting: H=0, V=0) (4) After 10 seconds, set up screen disappears, and set up finishes. * If there is no button operation, set up screen disappears even during set up process.
• RESET ▶ A factory default reset will clear all of OSD information.
11
[ 2. PICTURE USER ] 1) [MODE] button to select CONTRAST, BRIGHTNESS, COLOR, TINT MENU. (Selected menu in red) 2) Push [UP/DOWN] button to change the settings of the diferent menu points.
CONTRAST BRIGHTNESS COLOR TINT
50 50 50 50
CONTRAST BRIGHTNESS COLOR TINT
50 50 50 50
CONTRAST BRIGHTNESS COLOR TINT
50 50 50 50
CONTRAST BRIGHTNESS COLOR TINT
50 50 50 50
[ 3. CAMERA ] 1) Press the mode button to choose CAM1; CAM2 will turn red. CAM1
MIRROR
2) Press the VOLUME UP, DOWN button. NORMAL/MIRROR sign will be appear in order to adjust the screen to the right or left or to reverse the image. NORMAL/ MIRROR signal will turn RED.
* NOTICE : If MIRROR mode is selected, the right and left of screen image will be reversed. However, any letters will be not be reversed.
12
5 AUTOPIC • When press the AUTO PIC button, PICTURE SETUP menu is displayed on screen.
CONTRAST BRIGHTNESS COLOR TINT
50 50 50 50
6 MUTE • This function can be operated by the remote control.
1) Press [MUTE] button to mute sound and display mute icon. 7 RECALL CAM1
VOLUME 30
1) Press [RECALL] button to check the MODE and Volume.
13
5 CHANGING REMOTE CONTROL BATTERY 7” TFT LCD COLOR MONITOR
1. Pull the battery cover to the direction of the arrow.
2. Place a battery with the (+) sign upward. (No. CR2025)
3. Put the battery case back into the remote control in the direction of the arrow.
14
DC INPUT
AUDIO
VIDEO
GREEN(CAMERA2)
BLACK(CAMERA1)
BLACK (CAMERA 1, Priority) FOR REAR VIEW Connect this line to “+” of reverse light lamp. GREEN (CAMERA 2) FOR SIDE VIEW Connect this line to “+” of side light lamp.
MDM-105A
CAMERA 2
CAMERA 1
CIGAR CABLE
CAMERA(OPTION)
6 CONNECTIONS 7” TFT LCD COLOR MONITOR
15
7 INSTALLATION 7” TFT LCD COLOR MONITOR
(1) Please set the place for Monitor installation. Clean the place where to install stand and install stand firmly after removing protect tape of stand bottom. (2) Fix the stand with enclosed screws. (3) Assemble the monitor to stand and fix it in the right angle. (4) Connect cable as follows.
Fix Knob (Bracket) Tapping Screw
Stand
Protect tape Control Konb (Angle)
16
8 SPECIFICATION 7” TFT LCD COLOR MONITOR
SPECIFICATION ITEM
LCD PANEL
POWER SUPPLY INPUT SYSTEM FREQUENCY VIDEO INPUT SIGNAL
NTSC 17.78 cm (7.0 inch)
DISPLAY FOMAT
800(H) x 3(RGB) x 480(V)
BRIGHTNESS
400 cd/m2
Contrast ratio
500:1
ACTIVE AREA
154.08 (W) x 86.92 (H) mm
VIEW ANGLE
70˚(L) / 70˚(R) / 50˚(U) / 70˚(D)
VOLTAGE
DC 12V - 24V
CONSUMPTION
450mA Max (DC 12V, Monitor Set Only)
AUTO (NTSC/PAL) HORIZONTAL
15.734 Khz
15.625 Khz
VERTICAL
60 Hz
50 Hz
Composite Video 75Ω 1Vp-p
OSD DISPLAY
7 Language
OPERATING TEMPERATURE
-30˚C ~ 70˚C
STORAGE TEMPERATURE
-40˚C ~ 80˚C
DIMENSION WEIGHT
PAL
SCREEN SIZE
201(W) x 117(H) x 30.7(D) mm 450g
** The design and specifications of this product in order to improve its quality may be changed without notice.
17
MEMO
MEMO
INSTRUCTION MANUAL
