Transcript
cmosSamBa HR-130 FEATURES: Remote head - small and space-saving Global- and rolling shutter Multiple slope Very high dynamic range Inexpensive high-performance Single 5V power supply Modular, scalable design: adapt to multiple applications Galv.-isolated I/Os: for industrial environments Camera Link interface or standard RS-644 LVDS AIA Digital Camera interface Externel trigger, shutter
APPLICATIONS: Machine vision & inspection Semiconductor Medical instrumentation Robotics Traffic supervision Surveillance, especially with Web technology All applications where space is limited For small, inexpensive instruments
www.sensovation.com
SPECIFICATIONS:
1.3 MPixel CMOS Camera with miniature remote-head Parameter
Specification
Parameter
Specification
Units
CMOS Image sensor architecture
4-Transistor active pixel sensor (APS) 2/3’’ optical format. On-chip FPN correction, programmable offset & gain. All IBIS 5A functions are register programmable.
Wavelength range (Refer to QE curve)
400 to 1000
nm
> 30
% e-
Fill factor Full Well Capacity
62500
410
pA/cm_ e-/pix/s
< 40
e- rms
8
%
Fixed pattern noise (FPN)
< 0.2
% rms
Windowing & sub-sampling
Photo response non-uniformity (PRNU)
< 10 2
Pixel rate
Programmable 20 MHz or 40 MHz
Conversion gain
17.6
% P-P % rms µV/e%
Linear: 64dB, extendable via multiple-slope operation up to 100 dB; Synchronous shutter: 1,2,3 or 4 slopes. External programmable reset voltage 0 - 4 V.
Parasitic sensitivity (sensitivity to light when synchronous shutter is off)
<1
Dynamic range
Integral linearity (Digital output vs. optical input, over the full dynamic range)
±1
% FS
Dark current, +25° C
Pixel resolution (active)
1280 horiz. X 1024 vert.
Sensitive area
8.576 mm horizontal x 6.861 mm vertical
CMOS image area pixel size
6.7 µm x 6.7 µm
Optical crosstalk to nearest neighbor
Shutter mode
Both synchronous and rolling shutter modes.
Readout modes
Digital output resolution
10 bits
Intelligent data processing in FPGA hardware
Hot pixel detection and moving-window filtering. More functions can be implemented on custom basis: Image summing, averaging, digital pixel summing, lookup tables, data calibration & correction, more complex windowing (ROI selection), smoothing, filtering, noise reduction.
Readout noise
Exposure time range Max frame rate , full resolution Framegrabber Ethernet Ethernet data rate (net image data transfer)
146
2 µs to 1 hr up to 27 0.286
Fps Fps
1
MB/s
Order information Order Number
SVSB11-MB-1001
Control of external components Implemented on custom basis. by the RISC CPU Galv.-isolated I/Os are programmable by the RISC CPU, or by data processing algorithms above. For example: Motor controls, switches, LEDs, RS-232 control of other instruments, shutters, triggering and other synchronization. Optical interface
C-mount
Mechanical mounting
Flange mount form front or back, C-mount rings.
Software download
All CPU and FPGA code are downloadable via ethernet.
cmosSamBa HR-130
Sensovation reserves the right to make changes to products and documentation without prior notice.
MECHANICAL DIMENSIONS:
40 32
M
4
1´´- 32 UN
C-mount adapter
Spacer ring 3 mm
M17 Adapter
27
130
118.4
105
26
25
Remote head with C-mount
1´´- 32 UN
65.4
6.4
RS-232 (9-Pin DSUB) Ethernet (RJ-45) LVDS Framegrabber (68-Pin HDSUB)
Connector to remote head
I/O (29-Pin HDSUB) DC-Power (9-Pin DSUB)
27
Power
130
118.4
105
6.4
I/0
Ethernet
Remote head front view
Serial
Remote head front view
5.7
Framegrabber
Remote Head
124 70
CCD active surface
Power
Ethernet
Remote head with flange and C-mount
I/0
Serial
Framegrabber
Remote Head
124 70
Remote head with flange
9.5
4
3
Flange
M 17
1´´- 32 UN 3
15
65.4
cmosSamBa HR-130 The cmosSamBa HR-130 from Sensovation is a high-resolution camera system, which applies the latest advances in cmos image sensor technology for cost-effective commercial applications. The cmosSamBa HR-130 consists of a remote head and a main camera control unit (CCU). The tiny 1” remote head may be as far as 10 m from the electronics unit. Intelligence can be scaled up by optionally adding a DSP System to the CCU. In all models, a RISC CPU system handles Ethernet communications, camera functions and control of external components, such as auto-focus, motors, light sources or temperature control. FPGAs provide accurate sensor timing and fast “inline” hardware data processing. Opto-isolated I/Os allow the cmosSamBa HR-130 to control external motors, electro-optics or temperature control etc. The cmosSamBa HR-130 interfaces to the host (PC or embedded system) via 100 Base-T Ethernet, and operates from a single 5 VDC power supply. For applications in which very high frame rates are necessary, an industry standard digital frame grabber interface or Camera-Link interface is optionally available. The Fill Factory IBIS-5A is a cmos imaging device representing state-of-the art in cmos and has exceptional specifications. Notable is its high fill-factor (QE) and hence high sensitivity, low dark current and low read-noise. It allows global synchronous shuttering (“no readout during exposure, no exposure during readout”), sub-area imaging, windowing and subsampling. It can furthermore operate in “multi-slope” mode, whereby its dynamic range attains 100 dB.
IMAGE SENSOR SPECIFICATION:
40%
0.18
30% 20%
Spectral response [A /W]
0.16 0.14 0.12 0.10
10%
0.08 0.06 0.04 0.02 0 400
500
600
700
800
900
1000
Wavelength [nm]
Spectral response curve
Source: Data Sheet Fill Factory IBIS5A
Sensovation AG Ludwigshafener Str. 29 D-78333 Stockach / Germany Phone: + 49 - 7771 8739 - 0 Fax: + 49 - 7771 8739 - 39
[email protected] www.sensovation.com
Sensovation Corp. 1301 Shoreway Road, Suite 101 Belmont, CA 94002 / U.S.A. Phone: 650 - 622 - 2820 Fax: 650 - 622 - 9075
[email protected] www.sensovation.com
600 / 18.03.05
cmosSamBa HR-130
