Transcript
REAR DETAIL
CMS6 ICTB The Tannoy CMS6 ICTB is a full bandwidth (75Hz - 20kHz), high quality ceiling monitor system based around a 165mm (6.5”) point source transducer. The CMS6 ICTB is made for applications where ceiling heights may be compromised, but where sonic quality for music and speech reinforcement are required.
The CMS6 ICTB is designed for blind mount applications, offering simple and cost-effective installation in new and existing buildings, while providing quality music reproduction and voice intelligibility for critical applications.
INSTALLED
The ICT drive unit is attached to a discrete 9” baffle for architectural appeal. The CMS6 ICTB is not equipped with a back can enclosure, permitting the speaker to be installed in wall or ceiling cavities of 2 3/4”. The transformer settings (15, 7.5, 3.75, 1.9 Watts) are easily commissioned by connecting the input wire to the appropriate transformer terminal during installation. A pre-installation ring (MR 60B) can be ordered for further structural support.
DRIVER DETAIL
The CMS6 ICTB is available for use in 4½ operation, and a THP 15 Watt transformer can be ordered and mounted to the baffle during installation for use in a distributed system.
CEILING MONITOR SYSTEMS
SIDE VIEW
The design of the ICT™ drive unit addresses the two most common component failures experienced in background music and sound reinforcement systems; the tweeter and the crossover. ICT or Inductive Coupling Technology uses a wireless electromagnetic tweeter that does not require a crossover and cannot be burned out from heavy use or misuse. The ICT dome uses a molded plastic cone and nitrile rubber surround, further enhancing durability and long term reliability.
TECHNICAL SPECIFICATIONS
SIDE ELEVATION
CMS6 ICTB SYSTEM
204mm (8")
System Type
Ceiling Monitor Loudspeaker
Frequency Response +/- 3dB(1)
75Hz - 20kHz
Recommended Amplifier Power
20 - 120 Watt / 4½ (optimum) Average Programme Peak
Power Handling(2)
Sensitivity 2.83 Volts @ 1 meter(3) Maximum SPL
50 Watt 100 Watt 200 Watt 92dB
THP 15 Transformer Low Impedance
Impedance
Nominal
76mm (3")
178mm (7")
(half space)
100dB 107dB
(average) (average)
113dB (peak)
4½
TOP ELEVATION
Wattage Tap Selections
THP 15 Transformer
15, 7.5, 3.75, 1.9 Watts
Dispersion
See Beamwidth Plot
90˚ Conical
Driver Complement
1 x 165mm (6.5”) ICT™ Point Source
Crossover
7kHz - Inductively Coupled
CONSTRUCTION Finish
White grille - paintable
Connectors Dimensions
Bare wire (speed clips provided)
Mounting Depth Baffle Diameter Cutout Size Mounting Panel Thickness
Shipping
Bandwidth vs Frequency 360
Quantity CMS6 ICTB CMS6 ICTB-15 Pack Dimensions
2 2.5kg (5lbs 7oz) 3.0kg (6lbs 8oz) 210 x 267 x 210mm (81/4x 10 1/2 x 8 1/4“)
330 300 270
MR 60B Pre-installation Ring
240 210 180 150 120 90 60 30 0
250
315
400
500
630
80
100
1250 1600 2000 2500 3150 4000 5000 6300 8000 10000
Frequency (Hz)
(1) Average over stated bandwidth. Measured at 1 meter on axis. (2) Long term power handling capacity as defined in EIA standard RS - 426A. (3) Unweighted pink noise input, measured at 1 meter in an anechoic chamber
A full range of measurements, performance data, and Ease™ Data can be downloaded from www.tannoy.com Tannoy operates a policy of continuous research and development. The introduction of new materials or manufacturing methods will always equal or exceed the published specifications, which Tannoy reserves the right to alter without prior notice. Please verify the latest specifications when dealing with critical applications.
APPLICATIONS • Foreground music & paging systems • High level music and speech reinforcement • Lounges, bars, boutiques • Reception / waiting rooms • Airports, convention centers, hotels • Business music systems • Boardrooms & offices • Cruise ships • Retail outlets • Houses of worship
FEATURES • 6.5” ICT™ Transducer for greater durability and longevity • 90˚ controlled conical dispersion for optimum coverage and forward gain • Low insertion loss 15 Watt line transformer for a more powerful and dynamic performance • High power handling for higher output • Phase coherent design for superior vocal articulation and music quality • No crossover required - better phase, impedance and sensitivity response • Extended bandwidth for high fidelity • Multi tap voltage and wattage to suit virtually any application • Five year loudspeaker warranty
ARCHITECTURAL SPECIFICATIONS The Ceiling Monitor System shall consist of a 165mm (6.5") full range, single Point Source ICT™ Transducer. The system shall be powered by the THP 15 high performance transformer offering 70.7 Volt and 100 Volt operations with 15, 7.5, 3.75 and 1.9 Watt taps available. Performance of the ceiling monitor shall meet or exceed the following criteria. Frequency response 1 meter on axis with swept sine wave shall be 75Hz to 20kHz +/- 3dB, sensitivity shall be at least 92dB for 2.83 Volts @ 1 meter with minimal insertion loss accounted for. The driver impedance and maximum power handling (without transformer) shall be 4½ and 100 Watts respectively. The system shall not exceed the following dimensions: 87 x 213mm (3 7/16 x 8 3/8") (H x Dia) The Ceiling Monitor System shall be the Tannoy... CMS6 ICTB.
Tannoy United Kingdom
T: +44 (0) 1236 420199
F: +44 (0) 1236 428230
E:
[email protected]
Tannoy North America
T: (519) 745 1158
F: (519) 745 2364
E:
[email protected]
C71L.0603
CMS6 ICTB
BEAMWIDTH PLOT
CMS6 ICTB 1.1kg (2lbs 6oz) CMS6 ICTB-15 1.6kg (3lbs 7oz)
Accessories (Optional) NOTES:
76mm (3“) 204mm (8“) 179mm (7 1/16") 23mm ( 7/8 “)
Degrees
Weight (each)
4mm (3/16")
