Colossus 15b-800 - Tout Le Haut Parleur

Transcript

PROFESSIONAL SERIES COLOSSUS 15B-600 COLOSSUS 15B-800 FREQUENCY RESPONSE DATA* +120 +110 +100 +90 dBr The Colossus 15B-800 is intended for use in high-power two-way ported enclosures and as a high-output bass driver in multi way systems. It features a 4 inch voice coil immersed in a symmetric magnetic field yielding increased linearity and lower distortion at high excursion levels. The cone membrane, manufactured from polycellulose, is much stronger and more durable than conventional paper pulp alternatives. This allows the driver to combine high-sensitivity with the structural integrity required to produce undistorted low frequencies at high output levels. The driver handles 800 Watts (A.E.S) continuous and can cope with peaks in excess of 3200 Watts. This is due to advanced thermal management in the form of vented die-cast chassis and motor system coupled to a large vaned heatsink mounted on the rear of the unit. These measures effectively remove heat from the voice coil, resulting in extremely low-power compression. The Colossus 15B-800 exhibits an average sensitivity of 100 dB and can deliver bass down to 40 Hz (-6 dB) in a 125 litre ported enclosure. +80 +70 +60 +50 20 50 100 200 500 1k 2k 5k 10k 20k Hz * Half space response measured in a 975 litre sealed box IMPEDANCE THIELE SMALL PARAMETERS Nominal Chassis Diameter Impedance Power Handling Peak Power (6dB Crest Factor) Usable Frequency Range -6dB Sensitivity (1 w - 1 m) Moving Mass inc. Air Load Minimum Impedance Zmin Effective Piston Diameter Peak Displacement Volume of Cone Vd Magnet Weight Magnetic Gap Depth Flux Density Coil Winding Height Voice Coil Diameter FS Hz RE Ohms Qms Qes Qts Vas Ltr Vd litres CMS (mm/N) BL T/m Mms (grms) Xmax (mm) Sd (cm2) Efficiency % Le (1k Hz) 15” 8.4 Ω 800 w (A.E.S.) 3200 w (A.E.S.) 40 Hz - 3 kHz 100 dB 103 grams 7.5 Ω 13.03” / 331 mm 0.98 litres 120 oz 0.43” / 11 mm 1.04 Tesla 0.75” / 19 mm 4.0” / 101.6 mm 42 Hz 6Ω 4.82 0.295 0.278 139 0.98 0.139 23.6 103 5.7 0.086 m2 3.51% 2.191 mH 200 100 50 20 Ohms ELECTRO ACOUSTIC SPECIFICATIONS 10 5 2 1 20 50 100 200 500 1k 2k 5k 10k 20k Hz PREDICTED BASS RESPONSE +6 0 MATERIALS OF CONSTRUCTION MOUNTING / SHIPPING INFORMATION Former Material Voice Coil Magnet Material Glass Fibre Copper Ferrite Chassis Cone Surround / Edge Termination Die-cast Aluminium Curvilinear polycellulose Polyvinyl Damped Dbl. Half Roll Linen Solid Paper Push-button Spring Terminals Positive Voltage at Red Terminal Causes Forward Motion of Cone Overall Diameter Width Across Flats Flange Height Baffle Hole Diameter F/M Baffle Hole Diameter R/M Gasket Supplied Fixing Holes Dust Dome Connectors Polarity Depth Weight Recommended Enclosure Volume Shipping Weight Packing Carton Dimensions • Please enquire about alternative impedances. A.E.S. power handling test. Pink noise bandpass filtered at 12 dB per octave with cutoff frequencies of 40 Hz and 400 Hz. Driver mounted in free air, test signal applied at rated power for two hours. Please note that the frequency response measurements are supplied for comparison only and are not a measure of the low frequency performance which may be achieved in a fully optimised system. -12 -18 -24 -30 -36 5 10 50 100 500 1k 5k 10k 20k Hz ** Normalized bass response in 125 litre tuned to 33Hz 15.25” 387.4 mm ” m 16 m 4 6. 40 • • 16” / 406.4 mm 15.25” / 387 mm 0.305” / 7.8 mm 13.85” / 352 mm 14” / 355.6 mm Front & Rear 4x 0.281” diam on 15.5 PCD / 8x 0.281 diam on 14.56 PCD 4x 7.1 mm diam on 393.7 PCD / 8x 7.1 diam on 370 PCD 7.20” / 183 mm 27.28 lb / 12.4 kg 2.47 - 4.41 cu ft / 70 - 125 litres 30.58 lb / 13.9 kg 415 x 415 x 250 mm dB -6 7.2” 183 mm 9.21” 234 mm