Transcript
Spektra s.r.l. BUSTO ARSIZIO (VA) 21052 Tel. / Fax 0331/340514 Cell. 339/1282223 VER 1.2 DEL 20/2/2008
VERSION 1.2 or LATER COMMAND LIST FOR PROGRAMMING THE BABI UNIT (VOICE / GPS / COMBO):
Warning: ALL THE INFORMATION INCLUDED IN THIS DOCUMENT ABOUT THE GPS SECTION, ARE INTENDED FOR FUTURE IMPLEMETATION OLNY. ALL THE COMMANDS MUST BE SENT THROUGH THE SMS CHANNEL USING THE FOLLOWING SEQUENCE. WAIT ABOUT 20 SECONDS BETWEEN ONE SMS AND EACH OTHER GIVING TO THE NETWORK THE RIGHT TIME TO DELIVER THE MESSAGE AND THE TIME TO THE UNIT TO DECODE AND DELETE THEM. IF YOU USE A COMBO UNIT (VOICE + GPS), YOU MAY CALL THEM TO THE VOICE NUMBER AND, LISTENING IT, SEND THE SMS COMMAND WITH ANOTHER PHONE, IN THIS CASE YOU WILL LISTEN A CONFIRMATION TONE WHEN THE SMS IS DELIVERED TO THE UNIT AND IT DECODE THEM.
•
LOCK/UNLOCK THE UNIT:
##P0
LOCK THE UNIT (THE UNIT IS LOCKED AND CAN NOT BE REPROGRAMMED)
##P1
UNLOCK THE UNIT (THE UNIT WILL ACCEPT THE PROGRAMMING COMMANDS)
NOTE: AFTER 3 HOURS OR AFTER A FORCED RESET WITH THE “##RESET” COMMAND, THE UNIT GO AUTOMATICALLY IN TO THE LOCK STATE TO PREVENT ACCIDENTALLY REPROGRAMMINGS
• NUMBER SETUP VOICE/DATA/SMS: THIS COMMAND SET OR DELETE THE NUMBERS CORRELATED WITH THE SPECIFIC FUNCTION (IS A GOOD OPTION TO SEND THE NUMBER WITH +XX… BEFORE THE TARGET NUMBER, WHERE XX IS THE INTERNATIONAL PREFIX NUMBER; EX: +39, +33, +44). ##NExxx*
SET THE INCOMING NUMBER, IF SET THE UNIT WILL ACCEPT ONLY CALL FROM THE PROGRAMMED NUMBER, xxx = TELEPHONE NUMBER
##NVxxx*
SET THE VOICE OUTGOING NUMBER THE UNIT WILL CALL THIS NUMBER IF A PHYSICAL MOTION IS MEASURED OR, IF ENABLED, IF THE VOX LEVEL IS REACHED, xxx = TELEPHONE NUMBER
##NDxxx*
SET THE DATA OUTGOING NUMBER THE UNIT WILL CALL THIS NUMBER IF A PHYSICAL MOTION IS MEASURED (FUTURE OPTION)
##NLxxx*
SET THE SMS LOCALIZATION NUMBER (FUTURE OPTION)
##NMxxx*
SET THE START SMS LOCALIZATION NUMBER (FUTURE OPTION)
##NSxxx*
SET THE STOP SMS LOCALIZATION NUMBER (FUTURE OPTION)
EX: ##NV+393471234567*
SET THE VOICE NUMBER
Note: TO DISABLE A SPECIFIC FUNCTION, YOU WILL SEND 5 ZEROS AS NUMBER TO THE SPECIFIC NUMBER COMMAND YOU WANT DISABLE EX: ##NV00000* TO DISABLE THE VOICE NUMBER. IMPORTANT NOTE: REMEMBER ALWAYS TO SEND AN ASTERISK ( * ) AT THE END OF THE NUMBER.
•
GENERAL FUNCTION:
##FORMAT
CLEAR ALL THE USER PROGRAMMED FUNCTION AND PUT THE UNIT IN TO THE FACTORY RESET STATE, THE UNIT WILL ALSO DO AN HARDWARE AND SOFTWARE RESET
##RESET
THE UNIT WILL DO AN HARDWARE AND SOFTWARE RESET WITHOUT LOOSING THE USER PROGRAMMED FUNCTION
##Qx
THE UNIT WILL GO IN TO THE SLEEP MODE FOR THE TIME LISTED IN THE FOLLOWING TABLE: x=1 -> 15 MINUTES x=2 -> 30 MINUTES x=3 -> 60 MINUTES x=4 -> 90 MINUTES x=5 -> 2 HOURS x=6 -> 4 HOURS x=7 -> 8 HOURS x=8 -> 16 HOURS x=9 -> 20 HOURS WHEN THE MESSAGE IS DECODED, THE UNIT WILL SHUTDOWN IMMDIATELY. IF IT IS DISCONNECTED FROM THE POWER, THE NEXT TIME IT WILL RECONNECTED IT SEEMS IT DOESN’T WORK OR IT IS BURNED. ALSO THE LED WILL NOT WORK. SO DON’T CONFUSE A SLEEPING UNIT WITH A BURNED OR DON’T WORKING UNIT. WAIT THAT THE SLEEPING TIME WILL END LEAVING THE UNIT CONNECTED TO THE POWER. ##Sx
MOTION SENSOR SENSIBILITY (0->9) (NOT USED IF THE UNIT IS CONFIGURED AS ‘MICRO’ WITH THE VOX FUNCTION) 0=MAXIMUM SENSIBILITY 9=MINIMUM SENSIBILITY
##TRxx
TIMEOUT ON RECALL, IF THE CALL END ABNORMALLY, THE UNIT WILL WAIT THIS TIME BEFORE TRY AGAIN TO RECALL THE TARGET NUMBER, xx = 00->99 MINUTES
##L0 ##L1
THE LED IS ALWAYS OFF THE LED IS IN NORMAL WORKING CONDITION (VARIOUS DIAGNOSTIC LED FLASH)
##RAN
DISABLE ALL THE RECALL FUNCTIONALITY WITHOUT DISABLE THE PROGRAMMED NUMBERS
•
VOICE COMMANDS:
##TVxx
VOICE TIMEOUT AFTER THE VEHICLE IS STOPPED, xx = 01->99 MINUTES
##TAVxx
VOICE TIMEOUT ON CALL, xx = 01->99 SECONDS, xx = 00 FUNCTION DISABLED (WHEN THE UNIT CALL THE TARGET, IS POSSIBLE TO TERMINATE THE OUTGOING CALL AFTER xx SECONDS. SO, YOU CAN USE THE UNIT AS REMOTE MOTION ALARM WITHOUT HAVING CALLING COST BECAUSE THE CALL WILL BE CLOSED BEFORE YOU RESPOND).
##Vx
MICROPHONE LEVEL 1->3 VOLUME MIC. = 1 MINIMUM VOLUME MIC. = 2 DEFAULT VOLUME MIC. = 3 MAXIMUM
##VOXxx
‘VOX’ SENSIBILITY, APPLICABLE ONLY IF THE UNIT IS SET AS ‘MICRO’ – DEFAULT=10 01=MAXIMUM SENSIBILITY 99=MINIMUM SENSIBILITY
##Mx
MICROPHONE SELECTION 0->4 SEL. MIC. 0=DUAL FUNCTION MIC1 + MIC2 SEL. MIC. 1=MIC1 ENABLE, MIC2 DISABLE SEL. MIC. 2=MIC1 DISABLE, MIC2 ENABLE SEL. MIC. 3=DYNAMIC1: MIC1 IF THE CAR IS STOPPED THEN MIC2 IF IT IS MOVING SEL. MIC. 4=DYNAMIC2: MIC2 IF THE CAR IS STOPPED THEN MIC1 IF IT IS MOVING
##EMxxx
DSP PARAMETER WHEN THE CAR IS MOVING xxx = 000->159 SEE THE TABLE IN APPENDIX 255 = DISABLE THE DSP FUNCTIONALITY DEFAULT=255
##EFxxx
DSP PARAMETER WHEN THE CAR IS STOPPED (SAME AS ##EM)
##FILTROx,y
ENABLE/DISABLE THE INTERNAL LOW PASS AND HI PASS FILTERS: 0,H = DISABLE THE HI PASS FILTER 1,H = ENABLE THE HI PASS FILTER 0,L = DISABLE THE LOW PASS FILTER 1,L = ENABLE THE LOW PASS FILTER DEFAULT=0,H + 0,L
##MICROx
1=ENABLE, 0=DISABLE THE ‘MICRO’ FUNCTIONALITY (IF ENABLE THE MOTION SENSOR IS DISABLE AND THE ‘VOX’ FUNCTIONALITY IS ENABLED). WHEN SWITCH THIS FUNCTIONALITY, REMEMBER TO RESET THE UNIT WITH THE APPROPRIATE COMMAND (##RESET) OR SWITCHING THE UNIT OFF AND THEN ON AGAIN. DEFAULT=0
##RV
IMMEDIATELY START A VIOCE RECALL ON THE PRE PROGRAMMED VOICE NUMBER
##RAV
ENABLE THE VOICE RECALL ON MOTION (WHEN PHYSICAL MOVEMENT IN MEASURED)
##RAI
ENABLE THE INFINITY VOICE RECALL (ALSO WITHOUT MOTION)
•
GPS COMMANDS: (FUTURE FUNCTIONALITY)
##TDxx
DATA TIMEOUT AFTER THE VEHICLE IS STOPPED, xx = 01->99 MINUTES (THE UNIT WILL CONTINUE ON MEMORIZE THE POINT AND / OR A DATA CALL IN PROGRESS FOR xx MINUTES)
##TADxx
DATA TIMEOUT ON CALL, xx = 01->99 SECONDS, xx = 00 FUNCTION DISABLED (WHEN THE UNIT CALL THE TARGET, IS POSSIBLE TO TERMINATE THE OUTGOING CALL AFTER xx SECONDS. SO, YOU CAN USE THE UNIT AS REMOTE MOTION ALARM WITHOUT HAVING CALLING COST BECAUSE THE CALL WILL BE CLOSED BEFORE YOU RESPOND).
##F0 ##F1
THE GPS SECTION WILL WORK DYNAMICALLY (WILL BE SWITCH ON OR OFF IF THE VEHICLE IS MOVING OR NOT) THE GPS SECTION WILL BE FORCED ALWAYS ON
##Cxx
TIME BETWEEN TWO POINT IN MEMORY, 02->90 SECONDS
##Hxx
TIME BETWEEN TWO LOCALIZATION SMS WILL BE SENT, 15->90 SECONDS
##RD
IMMEDIATELY START A DATA RECALL ON THE PREPROGRAMMED DATA NUMBER
##RAD
ENABLE THE DATA RECALL ON MOTION (WHEN PHYSICAL MOVEMENT IN MEASURED)
•
REMOTE DEBUG MESSAGES:
WITH THIS COMMANDS YOU CAN GET THE STATUS OF THE UNIT THROUGH SMS MESSAGES. THE DEBUG MESSAGES ARE SENT BACK TO THE NUMBER THAT ASK FOR THEM WITH THE SPECIFIC SMS COMMAND. THIS COMMANDS ARE NOT PROGRAMMING COMMANDS, SO THEY CAN WORK ALSO WITH THE UNIT IN LOCK MODE (##P0). ##D1
PAGE 1 PROGRAMMED NUMBER. KIND OF UNIT, NAME, FW VERSION, - D1 - ##NLoc - ##NMov - ##NStop - ##NVoce - ##NDati - ##NEntr
##D2
PAGE 2 GENERAL FUNCTIONS. - KIND OF UNIT, NAME, FW VERSION, - D2 - ##S - ##Batt.letto (ACTUAL READOUT OF THE BATTERY VALUE) - ##TR - ##RAN (KIND OF RECALL CONFIGURED) - ##L - IMEI (IMEI OF THE UNIT)
##D3
PAGE 3 GPS COMMANDS. - KIND OF UNIT, NAME, FW VERSION, - D3 - PUNTI (ACTUAL NUMBER OF POINT IN MEMORY) - ##F - ##C - ##H - ##A - ##TD - ##TAD
##D4
PAGE 4 VOICE COMMANDS. - KIND OF UNIT, NAME, FW VERSION, - D4 - ##V - ##M - ##TV - ##TAV - ##VOX - ##FILTRO - ##EM - ##EF - CONN_V (VOICE CALL STATE, 0=NO CALL IN PROGRESS, 1=CALL IN PROGRESS)
##D5
PAGE 5 ACTUAL STATE OF THE GPS SECTION. - KIND OF UNIT, NAME, FW VERSION, - D5 - DATA (ACUTAL GPS DATE – LAST MEASURED POINT) - ORA (ACTUAL GPS TIME – LAST MEASURED POINT) - LAT (ACTUAL GPS LATITUDE – LAST MEASURED POINT) - LON (ACTUAL GPS LONGITUDE – LAST MEASURED POINT) - VEL (ACTUAL GPS SPEED – LAST MEASURED POINT) - DIR (ACUTAL GPS COMPASS – LAST MEASURED POINT) - FIX_N (0=NO SAT IN VIEWI, 1=FIX OK, 2=FIX OK + WAAS/EGNOS CORRECTION USED) - SAT_N (ACUTAL GPS SAT NUMBER – LAST MEASURED POINT)
##D6
PAGE 6 ACTUAL STATE OF THE GSM SECTION. - KIND OF UNIT, NAME, FW VERSION, - D5 - SIGN (GSM SIGNAL STRENGTH) - MAIN CELL (MAIN CELL DATA)
##D7
PAGE 7 EXTEND STATE OF THE GSM SECTION. - DATA CELL (DATA OF ALL OTHER CELL IN VIEW)
##DA
ALL THE ABOVE MESSAGE ARE SENT FOR A COMPLETE DIAGNOSTIC (EXCEPT ‘D7’).
•
NOTE:
• • • •
THE MESSAGES D3 AND D5 WILL BE SENT ONLY FOR UNIT ‘GPS’ OR ‘COMBO’ THE MESSAGE D4 WILL BE SENT ONLY FOR UNIT ‘VOICE’ OR ‘COMBO’ THE MESSAGES D1, D2, D6, D7 WILL BE SENT FOR ALL THE KIND OF UNIT THE MESSAGE D7 WILL BE SENT ONLY WITH THE SPECIFIC REQUEST COMMAND ‘##D7’
•
GENERAL NOTE:
THE UNIT WILL BE AVAILABLE IN 3 POSSIBLE VARIANTS: -
GPS ONLY VOICE ONLY COMBO = VOICE + GPS
YOU CAN CHECK THE TYPE OF UNIT YOU HAVE USING ONE OF THE ABOVE DIAGNOSTIC COMMAND. EXAMPLE: ##D1. THE UNIT WILL ANSWER WITH: ‘AG-MICRO-BABI V1.0 – D1’ THE FIRST 2 LETTERS IDENTIFY THE TYPE OF UNIT YOU HAVE: - ‘AG’ COMBO TYPE - ‘A’ VOICE ONLY - ‘G’ GPS ONLY - IF ‘MICRO’ IS VISIBLE MEANS THAT THE UNIT IS CONFIGURED AS MICRO UNIT (VOX ENABLED AND MOTION SENSOR DISABLED) YOU CAN ALSO CHECK FOR THE TYPE OF UNIT LOOKING THE FLASH LED DURING THE POWER ON PROCEDURE: - 10 FLASHES VOICE WITH ‘MICRO’ FEATURES ENABLED - 5 FLASHES = COMBO - 2 FLASHES = GPS ONLY - 3 FLASHES = VOICE ONLY
IMPORTANT NOTE: IF THE UNIT IS CONFIGURED AS ‘MICRO’ THE VIOCE CALL WILL BE ONLY OUTGOING CALL, SO YOU CAN NOT CALL THE UNIT FOR LISTENING IT. YOU MUST CONFIGURE THE UNIT TO CALL YOU WITH THE ‘##RAV’ COMMAND AND THE ‘##NVxxxx*’ COMMAND.
•
APPENDIX :
THE FOLLOWING TABLE LIST THE RIGHT VALUES FOR CONFIGURING THE DSP OPTIONS (##EM, ##EF): FUNZIONE ECHO CANCELLER DYNAMIC ECHO SUPPRESSOR NOISE SUPPRESSION CONFORT NOISE INJECTION EXTRA SUPPRESSION OF NON-LINEAR ECHOES NON-LINEAR PREPROCESSING OF FAR-END SIGNAL
VALORE 1 2 4 8 16 128
NOTE: MANY DIFFERENT DSP FUNCTIONS MAY BE ENABLED AT THE SAME TIME: SUM THE SINGLE VALUE IN THE TABLE AND SEND THE RESULT WITH THE APROPRIATE COMMAND (##EM, ##EF). SEND ALWAYS THE VALUE WITH 3 DIGITS. WITH THE ‘MICRO’ FEATURES ENABLED, USE THE ‘##EF’ COMMAND TO SET THE DSP, THE ‘##EM’ COMMAND WILL BE IGNORED.
