Combi Timer Electronic Single Channel 7 Day Etkit

Transcript

Part No.DOC.17 Rev.06 May 2011 USER INSTRUCTIONS General notes on using the timer The timer will automatically control the times at which your boiler operates for central heating each day of the week. It also provides a permanent display of the time of day (24hr or am/pm) and day of the week. A small indicator on the display shows when the heating is either ON or OFF. If the electricity supply to the boiler is interrupted, e.g during a power cut, the display will remain and the timer will retain the time and on/off program settings. It will not have to be reset when the supply is restored. The timer is supplied with three pre-set program options each giving different On/Off settings. Refer to Page 3 – 'To select and use a pre-set program' section. Alternatively, you can set your own program of On/Off settings, with different ON and OFF times for heating for different days of the week, if required. You can set up to 10 ON and 10 OFF commands throughout the week. Refer to page 5 – Setting your own program. Once set this program can be changed at any time as required. When setting the times for the ON periods it is useful to remember that it might take up to an hour for the house to become warm, especially in colder weather. Also the effect of the central heating will remain for a time when the central heating is turned off. While setting any times, if a period of more than 1 minute elapses since the last key was pressed, the timer automatically reverts back to the original program. Any changes made up to that point will be lost as they were not confirmed. To temporarily override the current switching time, i.e. change OFF to ON or ON to OFF, use the ‘+’ key on the Timer. Pressing the ‘+’ key will advance the Heating to the next program operation. NB. The timer will NOT automatically return to the set program at the start of the next program operation. Refer to Page 6 - To manually override automatic operation. For ‘Summer’ use the central heating can be set to OFF by pressing the ‘+’ key. Check that the ‘switching status’ display indicates that the heating function is OFF. Grant Engineering (UK) Limited Hopton House, Hopton Industrial Estate, Devizes, Wiltshire SN10 2EU Telephone: (01380) 736920 Fax: (01380) 736991 email: [email protected] website: www.grantuk.com This manual is accurate at the date of printing but will be superseded and should be disregarded if specifications and/or appearances are changed in the interests of continued product improvement. All goods sold are subject to our official Conditions of Sale, a copy of which may be obtained on application. © Grant Engineering (UK) Limited 2011. No part of this manual may be reproduced by any means without prior written consent. 8 ETKIT Fitting and User Instructions for Electronic Timer When setting the time for the start of the first ON period it must be after midnight. The time for the end of the last ON period can be after midnight. Refer to Page 6 – for the 'Shift' function section. Suitable for Vortex Pro Internal Combi e models and Indoor Grant Combi V3 & Combi Max models IMPORTANT These fitting Instructions must be read in conjunction with the wiring diagrams given in the Installation manual supplied with the boiler FITTING INSTRUCTIONS 1. Kit contents The Electronic Timer Kit (Ref. ETKIT) for Grant Vortex Pro Internal Combi e boilers and Indoor Grant Combi V3 & Combi Max boilers contains the following items: 1 x Grasslin 'Tactic' 7-day single channel electronic timer 1 x Wiring harness with plug (Note: plug is NOT required when used with Vortex pro Combi models) 1 x Fitting and User instructions 2. Electrical connections The kit is supplied with the wiring harness already connected to the electronic timer as follows: Blue wire: To Mains Neutral terminal 1 on the timer Red wire: To Mains Line terminal 2 on the timer Brown wire: To Common terminal 3 on the timer Brown wire: To Heating On terminal 4 on the timer . 3. Fitting procedure Important: Ensure the electrical supply to the boiler has been isolated before fitting the timer. Grant Combi V3 & Combi Max – Indoor models 1. Remove the front door and front top casing panel. 2. Loosen (do not remove) the four screws securing the control panel to the side panels. Hinge the control panel forwards and allow it to drop down to gain access to the rear of the panel. 3. Remove the two screws securing the terminal block cover and lift off the cover. 4. Remove the factory fitted link from terminals 8 and 9. 5. Remove the four screws from the rear of the control panel. Remove the rear access cover. 6. From underneath the control panel, remove the screw securing the bracket behind the timer aperture. Withdraw and discard the bracket. 7. Remove the blanking piece from the timer aperture, in the control panel fascia, by firmly pressing on the Grant logo (in the centre of the black square) until it is detached from the rear of the fascia. Remove the blanking piece from the panel and discard. 8. Fit the 6-way plug on the timer wiring harness, firmly into the 6-way socket inside the control panel, to connect the timer to the boiler. 9. Locate the electronic timer in the square aperture in control panel front. Secure by pressing in and turning the two screws (in upper right and lower left corners) a quarter turn clockwise. 1 10. Replace the rear cover of the control panel and secure with the four screws previously removed. 11. Replace the terminal block cover in position over the terminal block, taking care not to trap any wires, and secure in position with the two screws previously removed. 12. Hinge the control panel back into position on the two retaining screws and replace the front top casing panel. Reconnect the electricity supply and check the operation of the timer. Refer to the instructions on the following pages for operating and setting the timer. Vortex Pro Combi e – Indoor models 1. Remove front and top boiler casing panels. Loosen (do not remove) the four screws securing control panel to the side panels. Hinge the panel forward to access top and rear of control panel. 2. Remove the two screws and lift off the terminal block cover from top of control panel. 3. Remove the Black wire link from terminals 19 & 20 on control panel. DO NOT remove the Red link from terminals 17 & 18. 4. Carefully push through and remove square pre-cut 'knockout' section in the control panel front. 5. 6. 7. 8. 9. Disconnect and remove the plug from the end of the wiring harness. Do not disconnect any of the four wires from the terminals of the electronic timer. They must be connected as shown in the Diagram in Section 4 below. Feed the wires through hole in control panel front and then up through rectangular opening in control panel top. Connect wires to terminals on control panel – refer to Connection diagram. Locate the electronic timer in the square aperture in control panel front. Secure by pressing in and turning the two screws (in upper right and lower left corners) a quarter turn clockwise. Re-fit terminal block cover on control box and fasten with the two screws. Reconnect the electricity supply and check the operation of the timer. Refer to the instructions on the following pages for operating and setting the timer. IMPORTANT: After fitting the timer leave these instructions with the User 4. Connection diagram – For Vortex Pro Combi e boilers ONLY ETKIT Timer 1 M 2 3 4 Boiler wiring terminals Mains Neutral - Blue Blue Mains Line - Red 21 Red 22 Pro Combi e Boilers Brown 20 (internal models) Common - Brown Brown Heating ON - Brown 19 Programming sequence diagram Reset (first installation adjustment) Review/adjust Menu Set time: Format 24h or am/pm 24h blinking, using +/- to select, then OK to confirm Set time: Hour Hour blinking, using +/- to select, then OK to confirm Set time: Minute Minute blinking, using +/- to select, then OK to confirm Set time: Day Monday (1) blinking, using +/- to select, then OK to confirm Set Program: P01/ P02/ P03 Note: P01-P03 or P-Using +/- to select, then OK are pre-set To set ON/OFF times Or Press Menu to terminate programming P01is pre-set Menu OK Set Program: P01/ P02/ P03 or P– – Setting switching times: First free memory location blinks Press ‘-’ to go back one memory location Press OK for setting the switching times. Prog01 Setting switching times: First free memory location blinks Press OK for setting the switching times. Set switching ON time:Hour Hour blinking, using +/- to select, then OK to confirm Set switching ON time:Minute Minutes blinking, using +/- to select, then OK to confirm Set switching ON time:Days Mon Su (1 7) blinking, using +/- to select, then OK to confirm Set display: channel 1 or 2 Ch1 blinking, using +/- to select, then OK to confirm Set switching OFF time:Hour Hour blinking, using +/- to select, then OK to confirm Set switching OFF time:Mnute Minute blinking, using +/- to select, then OK/Menu to confirm 5 A maximum of 20 memory locations can be occupied: 10 switching ON times 10 switching OFF times NOTE: No wire connected to terminal 5 (’Heating Off’ terminal) Menu Run 2 7 1.3 Set hour 0 2 4 6 8 10 12 14 16 1 2 3 4 5 6 7 Press or 1 1 2 18 20 22 + - Res. Menu OK 1.6a Select P01 preset program 0 2 4 6 8 10 12 14 Res. Menu OK 1 Press or 2 16 1 2 3 4 5 6 7 18 + - Res. Menu OK 20 22 1h 24 24 1. Either select pre-set program P01 by pressing Menu or 2. Press ‘+’ to go to P02 1h 1. Select hour by pressing + or 2. Confirm setting by pressing OK 1h Res. Menu OK * 1h 1.6b Select P02 preset program 0 2 4 6 8 10 12 1.4 Set minutes 0 2 4 6 8 18 20 1 + 1 - 1 4 6 8 2 16 1 2 3 4 5 6 7 1 18 + - 2 Res. Menu OK 2. To set individual program P-Under the Menu option P-- you have the option of creating your own user defined program. This program can be changed at any time. There are up to 20 memory locations available for 10 OFF 10 ON commands throughout the week. You can allocate a corresponding week day or week block to each memory location. 0 2 4 6 8 0 2 4 6 8 22 - + - 2.4 Set week day ON 0 2 4 6 8 10 12 14 1 2 3 4 5 6 7 16 18 Press or 1 1 2 20 prog 22 + - Res. Menu OK 1h Res. Menu OK 1 Res. Menu OK 24 Press OK to confirm setting 2 Press or + 18 Res. Menu OK 2.5 Set first program hour OFF time (prog 2) 2.2 Set hour ON 20 0 2 4 6 8 10 12 22 14 1h 24 1. Select week day or days by pressing + or 2. Confirm setting by pressing OK 1h Possible week blocks and individual days 10 12 16 18 20 prog 1h Res. Menu OK 1h 10 12 1 16 1 2 3 4 5 6 7 Res. Menu OK 1h 24 Setting your own program Follow this sequence after setting the time, week day, etc. as shown in steps 1.1 to 1.5 then press ‘+’ three times until ‘P--’ shows on the display. Then press OK. 2.1 Select first program ON time (prog 01) 20 1h 1 2 3 4 5 6 7 1h Pressing ‘-’ will take you back to P01 1.6c Select P03 preset program 2 14 - 1 2 3 4 5 6 7 14 22 24 Res. Menu OK Press or 1 10 12 + 1. Either select pre-set program P02 by pressing Menu or 2. Press ‘+’ to go to P03 * 22 Res. Menu OK 24 Res. Menu OK 2 18 Res. Menu OK 20 1h 1. Select week day or by pressing + or 2. Confirm setting by pressing OK 5 = Friday 6 = Saturday 7 = Sunday 1 2 3 4 5 6 7 * 22 24 1h Press or 14 Press or 10 12 14 16 1 2 3 4 5 6 7 1h 1. Select minutes by pressing + or 2. Confirm setting by pressing OK 1h 14 1.5 Set week day 0 1. Either select pre-set program P03 by pressing Menu or 2. Press ‘+’ to go to P-to set your own program 16 1 2 3 4 5 6 7 Res. Menu OK 1 = Monday 2 = Tuesday 3 = Wednesday 4 = Thursday 1.6 Select one of the pre-set programs Use the following sequence after setting the time, week day etc. * If you wish to modify a pre-set program do NOT press Menu after selecting the program – but go to 1.7 To modify pre-set programs next. 1.7 To modify preset programs First press OK. Then, using the OK key you can now run through the pre-set 0 2 4 6 8 10 12 program and modify any of 14 the ON/OFF settings. 16 1 2 Either: Use '+' or '-' keys 18 3 4 20 to modify setting, then press 5 22 6 prog OK to confirm new setting. 7 24 Or: Accept pre-set setting by pressing OK to move on to Res. Menu OK next setting. Press Menu when you have 1h completed your changes to the pre-set program. e.g. after selecting P02 you should also program: Sa-Su 22.30 ON (prog 05) 23.00 OFF (prog 06) Note: Pressing Menu terminates programming 16 Press or 1 0 1 22 + 2 4 6 8 10 12 2 18 20 prog - Res. Menu OK 24 14 1 2 3 4 5 6 7 16 Res. Menu OK 2 4 6 8 10 12 + 22 Press or + 1 - 2 Res. Menu OK 24 1h 1. Select hour by pressing + or 2. Confirm setting by pressing OK Res. Menu OK 1h 2.6 Set minutes OFF Press or 1 0 1 2 4 6 8 10 12 2 16 18 20 prog - Res. Menu OK 22 24 Res. Menu OK 1 18 20 prog 1h 1. Select hour by pressing + or 2. Confirm setting by pressing OK 1h 2.3 Set minutes ON 0 14 1 2 3 4 5 6 7 14 1 2 3 4 5 6 7 16 Press or 1 1 2 18 20 prog 22 + - Res. Menu OK 24 1h 1. Select minutes by pressing + or 2. Confirm setting by pressing OK 1h 1h 1. Select minutes by pressing + or 2. Confirm setting by pressing OK Res. Menu OK 1h 4 5 2.8 Set week day OFF 0 2 4 6 8 10 12 1 14 1 2 3 4 5 6 7 Press or 2 2 16 + 18 - Res. Menu OK 20 prog 22 24 Res. Menu OK 1h 1h 1. Select week day by pressing + or 2. Confirm setting by pressing OK and go to Prog 03 or press Menu to end program Should the OFF setting be the same day as the ON setting then press Menu to quit the programming mode, or select OK to go to a new program ON setting. Repeat this process to set second program ON time (prog 03) and second program OFF time (prog 04) and so on. e.g. Mo-Fr Mo-Fr 20.00pm - 03.00am ON 20.00pm - 03.00am ON 03.00am - 20.00pm OFF Tu - Sat 03.00am - 20.00pm OFF OFF ON OFF 3. To delete a program 3.1 Press Menu. Then keep pressing OK key until the ON time of the 1 2 program you want to delete. + - Res. Menu OK 1h 0 2 4 6 8 10 12 or 14 1 2 3 4 5 6 7 16 2 2 1 18 20 prog 22 + - Res. Menu OK 24 1h Res. Menu OK 1h 6 2 4 6 8 1 10 12 14 + - 1. Press OK. The hours flash 2. Press ‘+’ or ‘-’ until - - appears USER INSTRUCTIONS SETTING THE TIMER TIMER DISPLAY AND KEYS Note: The boiler ON/OFF switch must be set to ON before setting the timer. Res. Menu OK 16 1 2 3 4 5 6 7 0 2 4 6 8 10 12 18 1h 20 prog 22 24 Res. Menu OK 1h 1. Press OK to confirm 2. Press Menu to quit the programming mode Note: Program settings are deleted in ON-OFF pairs. If you delete a single ON setting, the corresponding OFF setting is also deleted. 14 1 2 3 4 5 6 7 16 18 20 prog 0 2 4 6 8 1 2 3 4 5 6 7 20 22 24 Res. Menu OK 1h 6 8 Switching status display ON Setting of 24h or am/pm Switching status display OFF By pressing the +1h key 1 hour is added to the current time. Summer/winter clock changes Manual operation/ fixed ON/fixed OFF +1h is shown on the display. Weekday display Automatic operation The +1h key is for the changeover from summer to winter time. or 10 12 16 18 20 + - Res. Menu OK 22 OFF ON 0 Overview of daily switching program 14 1 2 3 4 5 6 7 1. To select and use a pre-set program Three different programs (P01, P02 & P03) are pre-set to switch the Heating ON and OFF at the times shown on the diagrams below, e.g. P01 switches ON at 06.00 and OFF at 22.00 where P02 switches ON at 07.00 OFF at 12.00 ON again at 14.00 and OFF at 20.00. P01:Mo-Su. 1xON/OFF setting per day 1h 5. To manually override automatic operation If you want to override the automatic function of the timer and set the Heating to either ON or OFF, use the ‘+’ key as follows: 4 The method of setting the timer depends on whether you wish to use the pre-set ON/OFF programs or set your own operating program as follows: 1h 18 2 Res. Menu OK 10 12 16 0 22 24 4. To change from Summer to Winter time To quickly alter the time setting of the programmer when changing from Summer to Winter time, or back. + - Res. Menu OK By pressing +1h again 1 hour is subtracted from the current time. 20.00 24.00 03.00 Tuesday 20.00 24.00 3.2 2 0 14 Shift: Should the OFF setting be in the day following the ON setting press ‘+’ key. Then press Menu or OK. 0 03.00 Monday 3.3 06.00 ON OFF 07.00 0 OFF ON 12.00 14.00 24.00 20.00 P03:Mo-Su. 3xON/OFF settings per day ON OFF 07.00 ON 12.00 14.00 OFF ON 18.00 20.00 OFF 22.00 24.00 1.1 Press the Reset key using a ballpoint pen or paperclip until it ‘clicks’. Res: Reset - press using a ballpoint pen or paperclip until it ‘clicks’ Menu: By pressing the menu key programming is terminated and the system reverts to automatic operation 24.00 P02:Mo-Su. 2xON/OFF settings per day 0 +/- : Adjustment keys: By pressing the key longer than 2 sec you can adjust the timer in steps of 5 units 22.00 + - Res. Menu OK 1h 1.2 Set display to 24 hour or AM/PM 24 1h Pressing the ‘+’ key overrides the timer - either switching the Res. Menu OK Heating ON or OFF. NB. If the automatic program 1h setting is ON,then press the ‘+’ key twice to switch it OFF. If the automatic program setting is OFF, press the ’+’ once to switch it ON. The timer will NOT automatically return to the set program at the next ON/OFF switching operation. It will be necessary to manually switch the timer back to the required setting by pressing the ‘+’ key (as above). Automatic or Manual operation of Heating is indicated at the lower left part of the display. OK: Confirmation of programming 0 2 4 6 8 10 12 14 Note By pressing the Menu key you can adjust/review the values for: 16 1 2 3 4 5 6 7 Res. Menu OK Time (hours/minutes) Day of the week 1h Pre-set programs P01 to P03 1 1 + - 2 18 20 Res. Menu OK 22 24 1h 24h or AM/PM + - Press or Res. Menu OK 1h 1. Select either ‘24h’ for 24 hour display or ‘pm’ for am/pm display by pressing + or 2. Confirm setting by pressing OK 3