Components Installation Sheet Csa40-67-din 406-512 Mhz

Transcript

Installation Sheet CSA40-67-DIN 406-512 MHz COMPONENTS BEFORE ASSEMBLING YOUR ANTENNA PLEASE ENSURE THAT ALL THE COMPONENTS BELOW ARE INCLUDED IN THE KIT. M-8565 SCREEN SIDES QTY: 2 M-8565 SCREEN CENTRE QTY: 1 LARGE CLAMP PLATE QTY: 4 0A-40-67-DIN DIPOLE ASSEMBLY QTY: 1 CORNER BRACKET QTY: 12 M12 HEX NUT M6 FLAT WASHER M12 SPRING WASHER M12 FLAT WASHER M6x65 HEX HEAD BOLT M12x250 THREADED ROD M6 FLAT WASHER M6 SPRING WASHER M6 HEX NUT M6x65 BOLT ASSEMBLY QTY: 24 INS-40994-6 M12 STUD ASSEMBLY QTY: 4 Copyright RF Industries Pty Ltd 2012. Subject to change without notice. 1 rfiwireless.com.au Installation Sheet CSA40-67-DIN 406-512 MHz ANTENNA ASSEMBLY STEP 1: ASSEMBLE THE 2 SIDE SCREENS TO THE CENTRE SCREEN AS DEPICTED BELOW USING THE 8 CORNER BRACKETS AND THE 16 M6x65 BOLT ASSEMBLIES INCLUDED IN THE KIT. TIGHTEN THE M6 BOLTS TO 15Nm (11 lbf.ft). CORNER BRACKET SIDE SCREEN CENTRE SCREEN SIDE SCREEN M6x65 BOLT ASSEMBLY STEP 2: ASSEMBLE THE DIPOLE TO THE CENTRE SCREEN AS DEPICTED BELOW USING THE 2 LARGE CLAMP PLATES AND THE 4 M12 STUD ASSEMBLIES INCLUDED IN THE KIT. TIGHTEN THE M12 NUTS TO 55Nm (40 lbf.ft). LEAVE APPROXIMATELY 110mm PROTRUDING OUT THE BACK SIDE. 135 2MM (5.3") TOP OF BOOM TO TOP OF SCREEN 90 ° 2. CENTRE SCREEN 0A-40-67-DIN DIPOLE ASSEMBLY INS-40994-6 110 5 M12 STUD ASSEMBLY Copyright RF Industries Pty Ltd 2012. Subject to change without notice. 2 rfiwireless.com.au Installation Sheet CSA40-67-DIN 406-512 MHz ASSEMBLY INSTRUCTIONS continued STEP 3: WITH THE ANTENNA ASSEMBLY LOCATED ON THE MOUNTING TUBE ATTACH THE REMAINING 2 LARGE CLAMP PLATES AND TIGHTEN THE M12 NUTS CLAMPING THE ANTENNA ASSEMBLY TO THE MOUNTING TUBE. TIGHTEN TO 55Nm (40 lbf.ft) MOUNTING TUBE (NOT INCLUDED) ANTENNA MOUNTING HARDWARE HAS BEEN DESIGNED TO ACCEPT MOUNTING TUBE DIAMETERS IN THE RANGE OF 50-75mm (2-3") MOUNTING TUBE LENGTH TO BE SIZED BY INSTALLER TO SUIT INSTALLATION METHOD. PLEASE NOTE MOUNTING POLE NOT SUPPLIED. INS-40994-6 LARGE CLAMP PLATE Copyright RF Industries Pty Ltd 2012. Subject to change without notice. 3 rfiwireless.com.au Installation Sheet CSA40-67-DIN 406-512 MHz ASSEMBLY INSTRUCTIONS continued TYPICAL INSTALLATION THESE ITEMS NOT INCLUDED IN ANTENNA KIT: SCREENED ARRAY ASSEMBLY CSA-40-67-DIN TOWER OUTRIGGER TOWER CLAMPS MOUNT POLE TYPICAL INSTALLATION SIDE VIEW STRAIN RELIEVE FEED CABLE BACK TO SUPPORT STRUCTURE. SEAL CONNECTOR WITH A SUITABLE SELF AMALGAMATING TAPE. SCREENED ARRAY IS DESIGNED TO BE FIXED TO A TOWER MOUNTED POLE OR TOWER LEG. ENSURE THAT MOUNTING POLE, CLAMPS AND MOUNTING STRUCTURE IS APPROPRIATELY SIZED TO SUIT LOCAL WIND AND ICE INSTALLATION CONDITIONS. NOTE : MOUNTING POLE NOT SUPPLIED INS-40994-6 Copyright RF Industries Pty Ltd 2012. Subject to change without notice. 4 rfiwireless.com.au