Transcript
Compriband Super FR Fire Rated Acrylic Impregnated Foam Sealant Strip
Description Compriband Super FR is an acrylic impregnated foam sealant strip which when used under compression by 80% provides a fire seal for up to 4 hours in accordance with BS 476 Part 20 or for longer periods when used in conjunction with Alfasil FR or Alfacryl FR. At 80% compression the product also provides a high performance weatherseal (>600 Pa). The product is supplied in roll form pre-compressed and ready for immediate use with a self-adhesive backing. After positioning, the material expands to find its own level and creates a permanent elastic seal. The product remains flexible throughout its life and responds to continual expansion and contraction cycles caused by thermal and structural movement. Typical Uses Compriband Super FR is designed to be used for the linear sealing of movement joints in substantially brick, stone and cementaceous building elements for example in walls, partitions, around window and door frames, sectional buildings and insulated cladding panels. Surface Preparation No special surface preparation or primers are required but contact surfaces must be clean of dust, dirt, loose matter, grease and oils. Application Care must be taken not to stretch the material, especially at joints. Do not run Compriband Super FR around corners always make close fitting butt joints. Continuous seals are formed with taper lap or close fitting but joints. Instructions for use are enclosed in each carton supplied and should be followed closely. The material expands at a rate dependent on the ambient
temperature, expanding faster in warmer conditions. If required the rate of recovery may be delayed by cooling in a freezer immediately prior to installation. Alternatively, the recovery can be accelerated by warming the material after installation using an indirect heat source. Storage Store rolls horizontally and in original packaging between +5°C and +25°C in dry conditions and away from direct sunlight. Shelf life is approximately 12 months.
Health and Safety The product is not regarded as having any significant associated hazards. No special precautions are necessary but the use of gloves are recommended during handling and installation of the product, especially for persons with sensitive skin. Wash hands immediately after use. Material Safety Data Sheet is available upon request.
Compriband Super FR
Tremco illbruck Limited Bentall Business Park, Glover Washington, Tyne & Wear NE37 3JD Tel: 0191 419 0505 Fax: 0191 419 2200 Email:
[email protected] Website: www.tremco-illbruck.co.uk
Availability – Standard Sizes Size
Gap Size mm
2 3 4 5 6 8 10 12 16 20 25
2 2-3 3-4 4-5 5-6 7-8 9-10 10-12 14-16 17-20 22-25
Recommended Tape Width / Joint Depth (mm) 40 40 40 40 40 40 40 40 40 50 60
Expanded Thickness (mm) 10 15 20 25 30 40 50 60 80 100 125
Roll Length (m) 8 6 6 4 4 4 4 4 3 3 3
All dimensions are subject to tolerances. If dimensional tolerances are of particular interest please consult the sales office. Physical Properties Characteristic Impregnation system Adhesive coating Colour Density Dimensional tolerances Tensile Strength Extension at Break Elastic recovery Rain Resistance @ 80% compression (supplied pre-compressed by approx 85%)
Fire Class
Units / Test Method
ISO1798 ISO1798 %
Specification Acrylic polymer Acrylic with carrier and red thread Mid / pale grey 80 Kg.m-3 Nominal +/- 5% >200 kPa* >200%* > 95
NEN6069
> 600 Pa
DIN4102 Part 1 BS 476 Part 20 10mm Vertical Joint
Fire resistance (detailed independent test report available upon request)1
Operating Temperature Thermal Conductivity Mould Resistance Biological Root Penetration Effect of water, salts and alkalis Compatibility Dimensional tolerances
20mm Vertical Joint
NEN 6069 °C W/m/K DIN 4062
B1 > 4 hours > 5 hours with Alfasil FR >5 hours with Alfacryl FR >3 hours > 5 hours with Alfasil FR > 5 hours with Alfacryl FR >60 min -30 to +90 0.065 Yes None None Most sealants and common building materials Nominal +/- 5% or 1 mm which ever is greater * Excluding adhesive layer
1
ISSUE 3 04/12/2007
The fire resistance of Compriband Super FR depends upon: 1. The width of the joint to be sealed 2. The depth of joint to be sealed 3. The type of structure involved. 4. The compression factor used. 5. Whether or not an appropriate capping sealant is used.
a brand of
ABCD
Whilst every care has been taken in the preparation of this information, no warranty is given or implied in connection with any recommendation or suggestion made herein or by our Representatives, Agents or Distributors. We reserve the right to modify specifications from time to time without prior notice. Users are advised to conduct their own tests in order to determine the suitability of the Product for the intended purpose. All goods are supplied subject to standard Conditions of Sale which are available upon request.
