Transcript
Table of Contents
Configure Your FuzzyScan........................................................1-1
Appendix...................................................................................A-1
Bar Code Programming Menu...................................................1-2
Keyboard Function Code Table .................................................A-2
Programming Procedures ..........................................................1-3
ASCII Input Shortcut .................................................................A-3
Host Interface Selection ............................................................2-1
Bar Code Command List ...........................................................A-5
Symbology Reading Control ..................................................... 2-3
Bar Code Command Menu ........................................................A-9
Keyboard Interface Control.......................................................2-13
Bar Code System Command......................................................A-10
Serial Interface Control ............................................................. 2-16 Wand Emulation Control ........................................................... 2-18 OCIA Interface Setting ..............................................................2-19 Operating Control......................................................................2-20 Condensed DataWizard .............................................................2-25
Bar Code Programming Guide
Configure Your FuzzyScan Before you trying to configure the FuzzyScan, please refer to the Quick Reference for basic installation. Otherwise, unexpected conditions may occur while setting the FuzzyScan. There are two ways to configure your FuzzyScan, depending on the model you brought from your vendors. Via FuzzyScan PowerTool PowerTool is a unique software utility designed for FuzzyScan scanners. It is designed to operate under Microsoft Windows 95/98/NT/2000/XP or above. To use the PowerTool, you will enjoy the convenience on your fingertip. Please refer to FuzzyScan PowerTool User’s Guide for details. Via Bar Code Programming Guide The Bar Code Programming Guide is designed for field programming convenience. All FuzzyScan family scanners can take this way to make detailed configurations. Before you using the Bar Code Programming Guide, please understand the command structure and various programming procedures in advance.
1-1
Bar Code Programming Guide
Bar Code Programming Guide System Command
The FuzzyScan bar code commands are specially designed Proprietary bar code labels which allow you to set the FuzzyScan internal programming parameters. There are System Command, Family Code and Option Code for programming purpose.
The System Command is the highest level bar code command which directs FuzzyScan to perform immediate operations, such as entering programming mode (PROGRAM), exiting programming mode (EXIT), listing system information (SYSLIST), recovering to factory preset configurations (M_DEFAULT), and so on. Please note that all system commands will take a few seconds to complete the operations. User must wait for the completion beeps before scanning another bar code.
Each programmable family and bar code command label is listed on the same page with major system commands. The detailed explanations and special programming flowchart are printed on facing or following pages. You can read the explanation and set the FuzzyScan concurrently. A supplemental bar code command menu incorporates the bar code command labels of System Command and Option Code. As you set the FuzzyScan, open the bar code command menu to find the option code page. You may scan the desired family code and option code to set FuzzyScan. If you want to change the programming family for multiple settings, you need only turn over the programming page to find next desired programming family.
Family Code The Family Code is scanned to select the user desired programming family. FuzzyScan has already provided more than one hundred programming families to meet any specific requirements. Option Code The Option Codes is a set of bar code commands represented by “0–9”, “A–F” and finishing selection (FIN). For most setting, you must select at least one option code following the family code selection to set the desired parameter for the selected programming family. 1-2
Bar Code Programming Guide
Programming Procedures
If the programming family must take multiple scans selection, cycling scan selection, or dual level selection procedures, the family of the programming menu will be marked with the matched representing symbol of Programming Category (P.C.) in bold font listed in the following table. You can easily find the bold mark in the programming menu, and refer to their flowcharts for details. Before setting the FuzzyScan, please also refer to the “Beeping Indications” listed in Appendix to understand the details of programming beeping indications. It will be very helpful for you to know the existing status while you are programming the FuzzyScan.
As you scan the bar code command to select the desired parameters, information about the final selected parameters represented by the bar code commands are stored in the FuzzyScan’s internal Flash Memory ASIC or non-volatile memory. If you turn off the unit, the Flash Memory ASIC or non-volatile memory retains all programming options. You need not re-program the FuzzyScan if you want to keep the existing configurations in the next power on. The programming procedures of FuzzyScan are designed as simple as possible for ease of setting. Most programming families take the Single Scan Selection programming procedure. But several programming families have more complex and flexible programmable options, and you must take Multiple Scans Selection, Cycling Scan Selection or Dual Level Selection to complete their programming procedures. Each kind of programming procedure is listed in the following pages for your reference. Please give careful attention to become familiar with each programming procedure. However, if you are the user of FuzzyScan Gold/Jade/Diamond series scanners, you are encouraged to use the PowerTool for convenience.
Conventions of Programming Menu Conventions
Descriptions Factory Default Value
P.C.
Programming Category SS : Signle scan selection MS : Multiple scans selection CS : Cycling scan selection DS : Dual level scan selection
1-3
(
)
Necessary Option Code
[
]
Selectable Option Code
Configure Your FuzzyScan
Program & End
System List & Master Default Scan “PROGRAM”
Scan “SYSLIST” FuzzyScan will list the product information and
FuzzyScan will enter programming mode, and inhibit all non-programming functions.
revision number to host via selected host interface, then issue the completion beeping (3 short beeps).
Scan “END”
Scan “M_DEFAULT”
FuzzyScan will exit programming mode, and store all parameters in Flash Memory ASIC or non-volatile memory, then issue the completion beeping (3 short beeps).
FuzzyScan will recover all programmable parameters into factory preset configurations, then issue the completion beeping (3 short beeps).
Please note that the FuzzyScan will take 3-4 seconds to store parameters in internal Flash Memory ASIC or non-volatile memory after you scan the “END”. Please don’t turn off the power before the completion beeping. It may destroy all configured parameters.
1-4
Configure Your FuzzyScan
Single scan selection Scan “PROGRAM”
Multiple scans selection Scan “PROGRAM”
Enter programming mode.
Enter programming mode.
Select one of desired
Scan One of Family Codes
programming families.
Scan One of Family Codes
Select one of desired programming families.
Select one option code of
Scan
desired parameter.
1. Select one or several
One of Option Codes
Yes
Scan One or Several Option Codes
programming family?
Yes
“FIN” to terminate
Repeat Selection
option code selection.
Want to select another
No Scan “END”
desired parameters. 2. If it’s necessary, scan
Want to select another
Repeat Selection
option codes to select
No
Exit programming mode.
Scan “END”
1-5
programming family?
Exit programming mode.
Configure Your FuzzyScan
Dual level selection
Cycling scan selection
Scan “PROGRAM”
Scan “PROGRAM”
Scan One of Family Codes
Enter programming mode.
Select one of desired
Scan One of Family Codes
programming families.
Cycling select one or
Scan One of Option Codes
(1st) Scan Several Option Codes
several option codes of desired parameters as “Single” or “Multiple”
(2nd) Scan One or Several Option Codes
Scan “FIN”
Repeat Selection
programming families.
Select several option codes of desired parameters. 1. Select one or several parameters. 2. If it’s necessary, scan
Finish cycling selection.
“FIN” to terminate
(If necessary)
option code selection.
Yes Want to select another
Repeat Selection
Want to select another programming family?
programming family?
No
No Scan “END”
Select one of desired
option codes of desired
scans selection.
Yes
Enter programming mode.
Scan “END”
Exit programming mode.
1-6
Exit programming mode.
Configure Your FuzzyScan
Host Interface Selection ♦ FuzzyScan Gold, Jade & Diamond Series ♦ PROGRAM
M_DEFAULT
Family Code Selection
P.C.
Host Interface Selection
MS
IBM PC/XT, 286/XT keyboard wedge interface
00
MS
IBM PC/AT, PS/1, PS/2, PS/VP series keyboard wedge interface
01
MS
Compaq, HP Vectra PC keyboard wedge interface
04
MS
Apple ADB keyboard wedge interface
05
MS
Standard/TTL RS-232 peer-to-peer serial interface
06
MS
Standard/TTL RS-232 serial wedge interface
07
MS
Wand emulation interface
08
MS
Pseudo RS-232 serial interface (TTL level, 3-wire connection only)
09
MS
PC/AT, PS/2 keyboard replacement interface (without external keyboard)
10
MS
Cino Omnikey & VersaNet direct-link interface
11
MS
HW-320 terminal keyboard wedge interface
12
MS
General Notebook PC keyboard wedge interface (with external keybaord)
13
MS
General Notebook PC keyboard direct-link interface (without external keyboard)
14
MS
IBM SureOne keyboard wedge interface
15
MS
IBM SureOne standard RS-232 serial interface
16
MS
Laser emulation interface (TBD - Please check your vendor for the availability.)
17
MS
USB keyboard interface (for Microsoft Windows 98, 2000 and Apple iMac)
18
MS
IBM 5550 series keyboard wedge (5p)
19
MS
IBM 5550 series keyboard wedge (6p)
1A
MS
SUN Microsystems Ultra 10 Workstation
1B
MS
DEC VT510 Keyboard Wedge (104-key)
21
MS
DEC VT510 Keyboard Wedge (105-key)
22
MS
IBM ThinkPad keyboard direct-link interface (without external pinpad)
84
MS
IBM ThinkPad keyboard wedge interface (with external pinpad)
87
for Gold/Jade/Diamond series
Parameter Selection
All the above listed host interface selections are not available for FuzzyScan Lite series. USB keyboard interface is only supported by Windows 98, Windows 2000 or above and Apple iMac system. 2-1
Option Code
Configure Your FuzzyScan
Host Interface Selection ♦ FuzzyScan Jade & Diamond Series ♦ PROGRAM
M_DEFAULT
Family Code Selection
P.C.
Host Interface Selection
MS
IBM PS/55 5576-001 (code set 81) keyboard wedge interface
70
MS
IBM PS/55 5576-002 (code set 81) keyboard wedge interface
71
MS
IBM PS/55 5576-003 (code set 81) keyboard wedge interface
72
MS
IBM PS/55 5576-A01 (code set 1) keyboard wedge interface
73
MS
IBM PS/55 5576-001 (code set 8A) keyboard wedge interface
74
MS
IBM PS/55 5576-002 (code set 8A) keyboard wedge interface
75
MS
IBM PS/55 5576-003 (code set 8A) keyboard wedge interface
76
MS
IBM PS/V PC, 5576-001 (code set 82) keyboard wedge interface
77
MS
IBM PS/V PC, 5576-002 (code set 82) keyboard wedge interface
78
MS
IBM PS/V PC, 5576-003 (code set 82) keyboard wedge interface
79
MS
IBM PS/V PC, 5576-A01 (code set 2) keyboard wedge interface
80
MS
Hitachi Flora KB1100 keyboard wedge interface
81
MS
Hitachi Flora KB3100 keyboard wedge interface
82
MS
Compaq Desktop PC keyboard wedge interface
83
MS
DOS/V keyboard direct link interface
85
MS
Fujitsu FMV keyboard wedge interface
86
MS
NEC NX Notebook direct link interface
89
MS
NEC PC-98 keyboard wedge interface
90
for Jade & Diamond series
Parameter Selection
Option Code
All of the above listed interfaces are not available for FuzzyScan Lite and Gold series. All of the above listed interfaces are specially for Japanese Machines. The Keyboard Wedge Interfaces of IBM/DEC/WYSE/TELEX, IBM 4683/4694 Traditional Interface and Variuos OCIA Interfaces are available with the FuzzyScan Diamond series only under OEM/ODM request. Please consult your local FuzzyScan vendor for details.
2-2
Configure Your FuzzyScan
Symbology Reading Control ♦ User Defined Symbol ID ♦ PROGRAM
M_DEFAULT
Family Code Selection
P.C.
Symbol ID : 1 character
DS
Symbol ID : 2 character
DS
Parameter Selection
Option Code
2nd Option Code
Code 128 (default=B)
00
(1 character)
UCC/EAN-128 (default=C)
01
(1 character)
UPC-A (default=A)
02
(1 character)
EAN/JAN/CAN-13 (default=F)
03
(1 character)
Codabar/NW-7 (default=D)
04
(1 character)
Code 39/Code 32 (default=G)
05
(1 character)
Code 93 (default=H)
06
(1 character)
Standard/Industrial 2 of 5 (default=I)
07
(1 character)
Interleaved 2 of 5 (default=J)
08
(1 character)
Matrix 2 of 5 (default=K)
09
(1 character)
China Postal Code (default=L)
10
(1 character)
German Postal Code (default=M)
11
(1 character)
IATA (default=O)
12
(1 character)
Code 11 (default=P)
13
(1 character)
MSI/Plessey (default=R)
14
(1 character)
UK/Plessey (default=S)
15
(1 character)
Telepen (default=T)
16
(1 character)
UPC-E (default=E0)
00
[1-2 characters], [FIN]
EAN-8 (default=FF)
01
[1-2 characters], [FIN]
To determine the hex value for the “Character”, please refer to the HEX/ASCII Reference Table found on page A-3.
2-3
Configure Your FuzzyScan
Symbology Reading Control ♦ Symbology ID Trans., Readable Bar Code Setting ♦ PROGRAM
M_DEFAULT
Family Code Selection
P.C.
Symbology ID Transmission
SS
Disable symbology ID transmission
0
SS
Enable prefix symbology ID transmission
1
SS
Enable suffix symbology ID transmission
2
SS
Enable both prefix and suffix symbology ID transmission
3
SS
Automatic discrimination
00
CS
Code 128, UCC/EAN-128
01
CS
UPC-A
02
CS
UPC-E
03
CS
EAN/CAN/JAN-13
04
CS
EAN/CAN/JAN-8
05
CS
Codabar/NW-7
06
CS
Code 39/Code 32, HIBC
07
CS
Code 25 Family, IATA
08
CS
Code 93
09
CS
Code 11
10
CS
MSI/Plessey
11
CS
UK/Plessey
12
CS
Telepen
13
Readable Symbology Setting
Remember to scan “FIN” to terminate this selection. But if you select the “ Automatic discrimination ”, FuzzyScan will terminate this selection automatically.
Parameter Selection
Option Code
If your application is reading known, limited bar code symbologies, you may increase the reading speed and decrease the reading error possibility by enabling those known symbologies only. Furthermore, to add the “Symbology ID” into the transmitted data is helpful for applications to identify the specific symbology ID. To further ensure fast, accurate readings, you can complete more complex configurations via full-feature DataWizard. To configure the full-feature DataWizard, user must use the PowerTool, a Windows 95/98/NT based software utility specially designed for FuzzyScan Universal Interface Models (Gold, Jade and Diamond series). Please consult your local FuzzyScan vendor for details.
2-4
Configure Your FuzzyScan
Symbology Reading Control ♦ Code 39/Code 32 Setting♦ PROGRAM
M_DEFAULT
Family Code Selection
P.C.
Code 39 Family Setting
SS
Select Standard Code 39 as primary format
0
SS
Select Full ASCII Code 39 as primary format
1
SS
Select Code 32 (Italian Pharmaceutical) as primary format
2
SS
Disable start/stop symbol transmission
3
SS
Enable start/stop symbol transmission
4
SS
Disable Code 32 leading A transmission
5
SS
Enable Code 32 leading A transmission
6
SS
Disable MOD 43 check digit verification
7
SS
Enable MOD 43 check digit verification
8
SS
Disable check digit transmission
9
SS
Enable check digit transmission
A
SS
Disable RS WIDE Code 39
B
SS
Enable RS WIDE Code 39
C
SS
Default (04)
FIN
MS
01-Maximum
(2 digits)
Code 39 Min. Length
Parameter Selection
Option Code
Scan 2 digits from the option code chart in Appendix, then FuzzyScan will terminate this selection automatically.
Code 39 Max. Length
SS
Default (99)
FIN
MS
99-Minimum
(2 digits)
Scan 2 digits from the option code chart in Appendix, then FuzzyScan will terminate this selection automatically. Selecting Full ASCII Code 39 disable Code 32 (both options may not be enabled at the same time). Standard Code 39 and Full ASCII Code 39 may be enabled at the same time, and Code 32 and standard Code 39 may be enabled at the same time.
2-5
Configure Your FuzzyScan
Symbology Reading Control ♦ Codabar/NW-7 Setting ♦ PROGRAM
M_DEFAULT
Family Code Selection
P.C.
Codabar Setting
SS
Select Codabar standard format
0
SS
Select Codabar ABC format
1
SS
Select Codabar CLSI format
2
SS
Select Codabar CX format
3
SS
Disable start/stop symbol transmission
4
SS
Enable ABCD/ABCD start/stop symbol transmission
5
SS
Enable abcd/abcd start/stop symbol transmission
6
SS
Enable ABCD/TN*E start/stop symbol transmission
7
SS
Enable abcd/tn*e start/stop symbol transmission
8
SS
Disable check digit verification
9
SS
Enable check digit verification
A
SS
Disable check digit transmission
B
SS
Enable check digit transmission
C
SS
Default (04)
FIN
MS
01-Maximum
(2 digits)
Codabar Min. Length
Parameter Selection
Option Code
Scan 2 digits from the option code chart in Appendix, then FuzzyScan will terminate this selection automatically.
Codabar Max. Length
SS
Default (99)
FIN
MS
99-Minimum
(2 digits)
Scan 2 digits from the option code chart in Appendix, then FuzzyScan will terminate this selection automatically.
2-6
Configure Your FuzzyScan
Symbology Reading Control ♦ UPC-A & UPC-E Setting ♦ PROGRAM
M_DEFAULT
Family Code Selection
P.C.
Parameter Selection
Option Code
UPC Family Setting
SS
Select UPC without supplement digits
0
SS
Select UPC with only 2 supplement digits
1
SS
Select UPC with only 5 supplement digits
2
SS
Select UPC with 2/5 supplement digits
3
SS
Disable UPC-E expansion
4
SS
Enable UPC-E expansion
5
SS
Disable UPC standardization
6
SS
Enable UPC standardization
7
SS
Disable UPC numeric system
8
SS
Enable UPC numeric system
9
SS
Disable UPC-A check digit transmission
A
SS
Enable UPC-A check digit transmission
B
SS
Disable UPC-E check digit transmission
C
SS
Enable UPC-E check digit transmission
D
SS
Disable UPC “leading 1” portion
E
SS
Enable UPC “leading 1” portion
F
UPC-E & EAN-8 Expansion
: Expand the 7-digit UPC-E and 8-digit ENA-8 to 12-digit UPC-A and 13-digit EAN-13.
UPC-A/E Standardization
: Expand the 7-digit UPC-E and 12-digit UPC-A to 8-digit UPC-8 to 13-digit EAN-13 with 1 zero insertion.
UPC Lead 1 Numeric System : Enable to read UPC leading with the 1 numeric system, you must enable this option. WPC Selection (UPC/EAN/JAN/CAN) UPC-A UPC-E EAN/JAN/CAN-13 EAN/JAN/CAN-8
Basic Length 12 7 13 8
Disable Check Digit -1 -1 -1 -1
Disable Numeric System -1 -1 NC NC
With 2-digit Addendum +2 +2 +2 +2
2-7
With 5-digit Addendum +5 +5 +5 +5
Enable Standardization +1 +1 NC NC
Enable Expansion 0 +5 0 +5
Configure Your FuzzyScan
Symbology Reading Control ♦ EAN/JAN/CAN & IATASetting ♦ PROGRAM
M_DEFAULT
Family Code Selection
P.C.
EAN/CAN/JAN Setting
SS
Select EAN without supplement digits
0
SS
Select EAN with only 2 supplement digits
1
SS
Select EAN with only 5 supplement digits
2
SS
Select EAN with 2/5 supplement digits
3
SS
Disable EAN-8 expansion
4
SS
Enable EAN-8 expansion
5
SS
Disable EAN-13 check digit transmission
6
SS
Enable EAN-13 check digit transmission
7
SS
Disable EAN-8 check digit transmission
8
SS
Enable EAN-8 check digit transmission
9
SS
Disable ISBN/ISSN Conversion reading check
A
SS
Enable ISBN/ISSN Conversion reading check
B
SS
Select 15-digit fixed length IATA checking
0
SS
Select variable length IATA
1
SS
Disable check digit verification
2
SS
Enable check digit automatic verification
3
SS
Enable S/N checking digit verification only
4
SS
Enable CPN checking digit verification only
5
SS
Enable CPN, Airline and S/N check digit verification
6
SS
Disable start/stop symbol transmission
7
SS
Enable start/stop symbol transmission
8
SS
Disable check digit transmission
9
SS
Enable check digit transmission
A
IATA Setting
Parameter Selection
2-8
Option Code
Configure Your FuzzyScan
Symbology Reading Control ♦ Code 25 Family & German Post Code Setting ♦ PROGRAM
M_DEFAULT
Family Code Selection
P.C.
Code 25 Setting
SS SS SS SS SS SS SS
Select any Code 25 Select Standard/Industrial 2 of 5 only Select Matrix 2 of 5 only Select Interleaved 2 of 5 only Select Interleaved 2 of 5 S Code only Select IATA only Select China Postal Code only
0 1 2 3 4 5 6
SS SS
Disable check digit verification Enable check digit verification
7 8
SS SS
Disable check digit transmission Enable check digit transmission
9 A
SS
Default (06)
FIN
MS
01-Maximum
(2 digits)
Code 25 Min. Length
Parameter Selection
Option Code
Scan 2 digits from the option code chart in Appendix, then FuzzyScan will terminate this selection automatically.
Code 25 Max. Length
SS
Default (99)
FIN
MS
99-Minimum
(2 digits)
Scan 2 digits from the option code chart in Appendix, then FuzzyScan will terminate this selection automatically.
German Postal Setting
SS
Disable
0
SS
Enable
1
The FuzzyScan can decode almost all Code 25 symbologies automatically. However, since the Code 25 encoding algorithm is not very robust, we recommend that you select only one kind of Code 25 for reading, or set limited maximum and minimum reading length for reading.
2-9
Configure Your FuzzyScan
Symbology Reading Control ♦ Code 11 & Code 93 Seting ♦ PROGRAM
M_DEFAULT
Family Code Selection
P.C.
Code 11 Setting
SS
Select 1-check digit verification
0
SS
Select 2-check digit verification
1
SS
Disable check digit transmission
2
SS
Enable 1-check digit transmission
3
SS
Enable 2-check digit transmission
4
SS
Default (04)
FIN
MS
01-Maximum
(2 digits)
Code 11 Min. Length
Parameter Selection
Option Code
Scan 2 digits from the option code chart in Appendix, then FuzzyScan will terminate this selection automatically.
Code 11 Max. Length
SS
Default (99)
FIN
MS
99-Minimum
(2 digits)
Scan 2 digits from the option code chart in Appendix, then FuzzyScan will terminate this selection automatically.
Code 93 Setting
SS SS
Disable check digit transmission Enable check digit transmission
0 1
Code 93 Min. Length
SS
Default (03)
FIN
MS
01-Maximum
(2 digits)
Scan 2 digits from the option code chart in Appendix, then FuzzyScan will terminate this selection automatically.
Code 93 Max. Length
SS
Default (99)
FIN
MS
99-Minimum
(2 digits)
Scan 2 digits from the option code chart in Appendix, then FuzzyScan will terminate this selection automatically.
2-10
Configure Your FuzzyScan
Symbology Reading Control ♦ MSI/Plessey, Code 128 & UCC/EAN 128 Setting ♦ PROGRAM
M_DEFAULT
Family Code Selection
P.C.
MSI/Plessey Setting
SS
Select MOD 10 check digit
0
SS
Select MOD 10-10 check digit
1
SS
Select MOD 11-10 check digit
2
SS
Disable check digit transmission
3
SS
Enable 1-check digit transmission
4
SS
Enable 2-check digit transmission
5
SS
Default (06)
FIN
MS
01-Maximum
(2 digits)
MSI/Plessey Min. Length
Parameter Selection
Option Code
Scan 2 digits from the option code chart in Appendix, then FuzzyScan will terminate this selection automatically.
MSI/Plessey Max. Length
SS
Default (99)
FIN
MS
99-Minimum
(2 digits)
Scan 2 digits from the option code chart in Appendix, then FuzzyScan will terminate this selection automatically.
Code 128/EAN-128 Setting
Code 128/EAN-128 Min. Length
SS
Disable function code conversion
0
SS
Enable function code conversion
1
SS
Default (04)
FIN
MS
01-Maximum
(2 digits)
Scan 2 digits from the option code chart in Appendix, then FuzzyScan will terminate this selection automatically.
Code 128/EAN-128 Max. Length
SS
Default (99)
FIN
MS
99-Minimum
(2 digits)
Scan 2 digits from the option code chart in Appendix, then FuzzyScan will terminate this selection automatically. 2-11
Configure Your FuzzyScan
Symbology Reading Control ♦ UK/Plessey & Telepen Setting ♦ PROGRAM
M_DEFAULT
Family Code Selection
P.C.
UK/Plessey Setting
SS
Select UK/Plessey Standard Format
0
SS
Select UK/Plessey CLSI Format
1
SS
Disable Convert X to A-F
2
SS
Enable Convert X to A-F
3
SS
Disable check digit transmission
4
SS
Enable check digit transmission
5
SS
Default (04)
MS
01-Maximum Scan 2 digits from the option code chart in Appendix, then FuzzyScan will terminate this selection automatically.
SS
Default (99)
MS
99-Minimum Scan 2 digits from the option code chart in Appendix, then FuzzyScan will terminate this selection automatically.
SS
Select Telepen Numeric mode
0
SS
Select Telepen Full ASCII mode
1
SS
Disable check digit transmission
2
SS
Enable check digit transmission
3
SS
Default (04)
MS
01-Maximum Scan 2 digits from the option code chart in Appendix, then FuzzyScan will terminate this selection automatically.
SS
Default (99)
MS
99-Minimum Scan 2 digits from the option code chart in Appendix, then FuzzyScan will terminate this selection automatically.
UK/Plessey Min. Length
UK/Plessey Max. Length
Telepen Setting
Telepen Min. Length
Telepen Max. Length
Parameter Selection
Option Code
FIN (2 digits)
FIN (2 digits)
FIN (2 digits)
FIN
2-12
(2 digits)
Configure Your FuzzyScan
Keyboard Interface Control ♦ Keyboard Layout (Language) Setting ♦ PROGRAM
M_DEFAULT
Family Code Selection
P.C.
Keyboard Layout
MS
USA (QWERTY)
00
MS
France (AZERTY)
01
MS
Germany (QWERTZ)
02
MS
United Kingdom - UK (QWERTY)
03
MS
Canadian French (QWERTY)
04
MS
Spain (QWERTY)
05
MS
Sweden/Finland (QWERTY)
06
MS
Portugal (QWERTY)
07
MS
Norway (QWERTY)
08
MS
Latin America (QWERTY)
09
MS
Italy (QWERTY)
10
MS
Netherlands (QWERTY)
11
MS
Denmark (QWERTY)
12
MS
Belgium (AZERTY)
13
MS
Switzerland-Germany (QWERTY)
14
MS
Iceland (QWERTY)
15
MS
Japan (DOS/V)
16
MS
Universal (only available for IBM PC/AT, PS/VP in MS DOS and Windows Mode)
99
The “Universal Selection” is only for PC/AT, PS/VP, PS/2 and compatible ones in DOS or Windows environment which can perform unique output without Caps Lock on/off (Output Style) concern. All transmitted data will follow the original full ASCII form. You also need not worry about the upper/lower case control.
Parameter Selection
Option Code
Please refer to the ASCII/HEX Table listed in the Appendix to determine HEX codes for characters, symbols, and functions to be used as premble or postamble. To set preamble or postamble as function key output, you must enable the “Function Key Emulation” feature as listed in page 3-25 first. Keyboard Interface Message String : Preamble
Data Length
Prefix Symbol ID
Scanned Data
Suffix Symbol ID
Postamble
Record Suffix
1-15 characters
2-3 digits
1 or 2 characters
variable length
1 or 2 characters
1-15 characters
1 character
2-13
Configure Your FuzzyScan
Keyboard Interface Control ♦ Record Suffix, Preamble, Postamble & Delay Setting ♦ PROGRAM
M_DEFAULT
Family Code Selection
P.C.
Record Suffix
SS
None
0
SS
RETURN
1
SS
TAB
2
SS
SPACE
3
SS
ENTER (Numeric Key Pad)
4
MS
User defined character (1 character)
SS
None
MS
1-15 characters
Preamble
Parameter Selection
Option Code
5, (00-7F) FIN [00-7F], [FIN]
Maximum 15-character input; scan “FIN” to terminate this selection.
Postamble
SS
None
MS
1-15 characters
FIN [00-7F], [FIN]
Maximum 15-character input; scan “FIN” to terminate this selection.
Character Frame Control
SS
None
MS
1-99 msec.
FIN (2 digits)
Scan 2 digits from the option code chart in Appendix, then FuzzyScan will terminate this selection automatically.
Intermessage Delay
SS
None
MS
1-99 (x5) msec.
FIN (2 digits)
Scan 2 digits from the option code chart in Appendix, then FuzzyScan will terminate this selection automatically.
Intercharacter Delay
SS
None
MS
1-99 msec.
FIN (2 digits)
Scan 2 digits from the option code chart in Appendix, then FuzzyScan will terminate this selection automatically. 2-14
Configure Your FuzzyScan
Keyboard Interface Control ♦ Caps Lock Control & Emulation Setting ♦ PROGRAM
M_DEFAULT
Family Code Selection
P.C.
Caps Lock Control
SS
“Caps Lock Off” State
0
SS
“Caps Lock On” State
1
SS
Auto Detect (PC/AT, PS/2, Keyboard Replacement and DOS/V Machines only)
2
SS
Enable ASCII 00-31 code as keyboard function code output
0
SS
Ctrl-Output
1
Function Key Emulation
Parameter Selection
Option Code
Refer to Appendix – Keyboard Function Code Table for details.
Key Pad Emulation
Upper/Lower Case
SS
Disable key pad emulation
0
SS
Enable numeric output as key pad (Num Lock On) output
1
SS
Normal case (neglect the upper/lower case control)
0
SS
Inverse case (change all characters output to inverse case)
1
SS
Upper case (force all characters output as upper case)
2
SS
Lower case (force all characters output as lower case)
3
Character Frame Control is used to adjust timing gap between bytes within one character data output by FuzzyScan. Intercharacter Delay is a time delay between data characters output by FuzzyScan. These two parameters are used to synchronize data communication when : 1) the data transmission speed is too fast, characters may be skipped; 2) multitasking operation system or host computers in a network may slow down the keyboard handling; 3) various notebook or desktop PC systems require different timing parameter settings. Please always add one extra unit as safty margin when adjusting these two parameters. Intermessage Delay is a time delay between messages output by FuzzyScan. Increasing this delay will help host applications process the incoming data on time. The function of “Caps Lock Control” and “Key Pad Emulation” are only available for IBM PC/AT, PS/VP, PS/2 series personal computers and compatible machines. While selecting the other host interfaces, these selections don’t perform the above functions for you. Please check the actual Caps Lock state in use while software application is running. If the Caps Lock state is off, select “Caps Lock Off” state, then FuzzyScan will perform normal data transmission. If the Caps Lock state is on, select “Caps Lock On” state. Select “Auto Detect”, FuzzyScan will perform special transmission handshaking without changing the status of Caps Lock switch.
2-15
Configure Your FuzzyScan
Serial Interface Control ♦ Record Suffix, Handshaking & Time Out Setting ♦ PROGRAM
M_DEFAULT
Family Code Selection
P.C.
Parameter Selection
Option Code
STX/ETX Control
SS
Disable STX/ETX transmission
0
SS
Enable STX/ETX transmission
1
STX/ETX are two characters used to indicate the starting and ending of the total data frame transmitted via serial interface.
Record Suffix
Preamble
SS
None
0
SS
CR (0DH)
1
SS
LF (0AH)
2
SS
CRLF (0D0AH)
3
SS
TAB (09H)
4
SS
SPACE (20H)
5
SS
EOT (04H)
6
MS
User defined character (1 character)
SS
None
MS
1-15 characters
7, (00-7F) FIN [00-7F],[FIN]
Maximum 15-character input; scan “FIN” to terminate this selection.
Postamble
SS
None
MS
1-15 characters
FIN [00-7F],[FIN]
Maximum 15-character input; scan “FIN” to terminate this selection. Serial Interface Message String : STX
Preamble
Data Length
1 character
1-15 characters
2-3 digits
Prefix Symbol ID Scanned Data Suffix Symbol ID
Postamble
1 or 2 characters variable length 1 or 2 characters 1-15 characters
2-16
ETX
Record Suffix
1 character
1 character
Configure Your FuzzyScan
Serial Interface Control ♦ Baud Rate & Data Frame Setting ♦ PROGRAM
M_DEFAULT
Family Code Selection
P.C.
Handshaking Protocol
SS
None (free running mode)
0
SS
RTS/CTS (hardware handshaking)
1
SS
ACK/NAK (software handshaking)
2
SS
Xon/Xoff (software handshaking)
3
SS
38.4K BPS
1200 BPS
0
5
SS
19.2K BPS
600 BPS
1
6
SS
9600 BPS
300 BPS
2
7
SS
4800 BPS
115.2K BPS
3
8
SS
2400 BPS
Baud Rate (BPS)
Data Frame
Time Out Control
Parameter Selection
Option Code
4
SS
8, None, 1
7, Space, 1
0
8
SS
8, Odd, 1
7, Mark, 1
1
9
SS
8, Even, 1
7, None, 2
2
A
SS
8, Space, 1
7, Odd, 2
3
B
SS
8, Mark, 1
7, Even, 2
4
C
SS
8, None, 2
7, Space, 2
5
D
SS
7, Odd, 1
7, Mark, 2
6
E
SS
7, Even, 1
SS
None
1 second
0
3
SS
200 mseconds
2 seconds
1
4
SS
500 mseconds
5 seconds
2
5
7
User defined value (seconds)
MS
6, (2 digits)
When the RTS/CTS Hardware Handshaking option is selected, the RTS (request to send) and CTS (clear to send) signals will be issued before normal data communication. This option is very helpful to ensure the reliability of data communication. When the ACK/NAK Software Handshaking option is selected, the FuzzyScan waits for an ACK (acknowledge) or NAK (not acknowledge) from the host computer after each data transmission. If the NAK is received, FuzzyScan will re-send the data until receiving ACK. The Time Out Control is a pre-defined delay time for FuzzyScan to wait for handshaking, acknowledgment or non-acknowledgment from the host computer. 2-17
Configure Your FuzzyScan
Wand Emulation Control ♦ Output Polarity, Singal State, Margin/Module Time, etc.♦ PROGRAM
M_DEFAULT
Family Code Selection
P.C.
Parameter Selection
Option Code
Output Polarity
SS
High level (5Vdc) on Bar (low level on Space)
0
SS
Low level (0Vdc) on Bar (high level on Space)
1
Determine the output voltage level for both bar and space.
Initial Signal State
SS
High Level (5Vdc)
0
SS
Low Level (0Vdc)
1
Determine the initial state of output voltage level.
Margin Time
Module Time
Narrow/Wide Ratio
Code 39 Emulation
SS
10 mseconds
30 mseconds
0
4
SS
15 mseconds
50 mseconds
1
5
SS
20 mseconds
2
6
SS
25 mseconds
100 mseconds Delay time before data transmission
SS
Extremely short
Long
0
SS
Short
3 3
1 Time base of minimum narrow bar
SS
Medium
2
SS
1:2
0
SS
1:2.5
1
SS
1:3
2
SS
Disable standard Code 39 emulation
0
SS
Enable standard Code 39 skip emulation
1
SS
Enable standard Code 39 replace emulation
2
[ Code 39 Skip ] : When this option is selected, all scanned data will be translated as Standard Code 39 wand emulation output. If any lower case characters are read, they will be translated to upper case characters. Any other characters that are not available in Code 39 symbology set will be skipped. [ Code 39 Replace] : Any character not normally available in the standard Code 39 symbology set, will be translated as Space.
2-18
Configure Your FuzzyScan
OCIA Interface ♦ OCIA Interface Setting ♦ PROGRAM
M_DEFAULT
Family Code Selection
P.C.
Parameter Selection
Option Code
OCIA Output Format
SS
NCR-S-format
0
SS
NCR-F-format
1
SS
DTS/Nixdorf
2
SS
Siemens
3
SS
Spectra Physics
4
SS
TEC
5
SS
CASIO
6
SS
Fujitsu
7
These special interfaces are only available for OEM/ODM. Due to varieties on data format, pin-assignment, and connector type in the market, please prepare related information and check with the manufacturer first to verify compatibility. Quantity commitment is necessary on these models.
2-19
Configure Your FuzzyScan
Operation Control ♦ Operation Mode, Buzzer Tone, Scanning Tolerance ♦ PROGRAM
M_DEFAULT
Family Code Selection
P.C.
Operation Mode
SS
Low Power mode (Low Power triggering)
0
SS
Trigger mode (External triggering)
1
SS
Level mode (Auto power off)
2
SS
Alternative mode (Periodic power off)
3
SS
Flash mode (Pulse driven reading)
4
SS
Force mode (Continued power on)
5
SS
Toggle mode (Repeat reading)
6
SS
Diagnostic mode (Test reading)
7
SS
Buzzer tone - mute
0
SS
Buzzer tone – low
1
SS
Buzzer tone - medium
2
SS
Buzzer tone - high
3
SS
Buzzer tone – extremely high
4
SS
Good-read beep before data transmission
5
SS
Good-read beep after data transmission
6
SS
Power-on beep
7
SS
No power-on beep
8
SS
Regular (standard) printing quality
0
SS
Poor (critical) printing quality
1
Buzzer Tone Adjust
Scanning Tolerance
(Printing Quality Control)
Parameter Selection
Option Code
Please note that if you select “Poor printing quality”, you should limit “Readable Bar Code Symbology” and “Minimum & Maximum Reading Length” of each symbology to avoid error reading.
The “Scanning Tolerance” provides the user with a helpful tool to use when the printing quality of the bar code is poor. This is a programmable feature with software revision CXX and older for both FBC-3000 series and FBC-6000 series. Units using later software revisions (DXX) perform this feature automatically without any extra programming. To reduce the error reading rate further, we also recommend that you limit the number of enabled symbologies to only those that you need to read. And to limit the minimum and maximum reading of each enabled bar code symbology. 2-20
Configure Your FuzzyScanu
Operation Control ♦ Dollar Sign, Double Scan Verification ♦ PROGRAM
M_DEFAULT
Family Code Selection
P.C.
Double Scan Verification
SS
Disable
Long time out duration
0
4
SS
Immediate time out duration
Force Verification
1
5
SS
Short time out duration
2
SS
Medium time out duration
3
SS
None
4 times
0
4
SS
1 time
5 times
1
5
SS
2 times
2
SS
3 times
3
SS
Short (around 2 seconds)
0
SS
Medium (around 3-4 seconds)
1
SS
Long (around 5-6 seconds)
2
SS
Extremely long (around 7-8 seconds)
3
SS
1/2 duty cycle
0
SS
2/3 duty cycle
1
SS
3/4 duty cycle
2
SS
4/5 duty cycle
3
SS
Disable
0
SS
Enable
1
SS
Dollar sign output as “$”
0
SS
Dollar sign output as “￥”
1
Dollar sign output as “ “ (TBD – Please check your vendor for the availability)
2
Redundancy (Scan Voting)
Auto Power Off Duration
Pulse Driven Duty
Inverse Bar Code Reading
Dollar Sign Control
Parameter Selection
The “Double Scan Verification” is designed to inhibit FuzzyScan from reading the same bar code label twice in pre-defined short duration. The Redundancy is the number of times the same bar code label has to be decoded before it is transmitted. 2-21
Option Code
Configure Your FuzzyScanu
Operation Control ♦ Digial I/O Output Control, Pulse Interval Control ♦ PROGRAM
M_DEFAULT
Family Code Selection
P.C.
Digital I/O Output Control
SS
Digital I/O output by user control
0
SS
Digital I/O output after good-read
1
SS
Output initial state as low
2
SS
Output initial state as high
3
SS
None (00)
SS
01-FF (x10) msec.
(for FBC-8000 Series Only) Pulse Interval Control
(for FBC-8000 Series Only)
Parameter Selection
Option Code
FIN (2 digits)
Scan 2 digits from the option code chart in Appendix, then FuzzyScan will terminate this selection automatically.
The Digital I/O Output Control is currently available only for FuzzyScan FBC-8000 series fixed mount linear imager. The Digital I/O Output Control provides the controls from or imposed on external devices upon preset reading conditions. The Pulse Interval Control is the setting for pulse interval of digital I/O output. The actual value of the pulse interval will be 10 times of the setting value. For example, if user sets the pulse interval as ‘05’, the actual interval should be 50msec.
2-22
Configure Your FuzzyScanu
Operation Control ♦ Operation Mode, Clear Memory, Data Memory Upload ♦ PROGRAM
M_DEFAULT
Family Code Selection
P.C.
Operation Mode
SS
On-line Scan mode
0
SS
Self-powered Scan mode
1
SS
Batch Scan mode
2
(for MBC-6000 Series Only) Clear Memory
(for MBC-6000 Series Only) Data Memory Upload
Parameter Selection
Option Code
Clear all scanned data stored in the memory.
Upload all scanned data stored in the memory into the host PC through the desired communication port. (*)
(for MBC-6000 Series Only) For MBC-6000 setup process, you will need to read END and FIN to terminate the selection in stead of just reading END. When set the Operation Mode to On-line Scan mode, you can use the MBC-6000 series imager as an on-line imager. When set the Operation Mode to Self-powerScan mode, you can use the MBC-6000 series imager as a self-powered scanning device with battery power supplied to the interface cable converters. When set the Operation Mode to Batch Scan mode, you can use the MBC-series imager as a batch memory imager with all scanned data stored in flash memory. (*): Host interface port has to be specified first. Then, proper interface cable converter has to be connected accordingly for data file to be sent to host correctly. Please refer to page 2-7 Host Interface Selection and page A-5 of various Host Interface Quick Set Command for details.
2-23
Configure Your FuzzyScanu
Operation Control ♦ Data Storage Format (Number of field, etc) ♦ PROGRAM
M_DEFAULT
Family Code Selection
P.C.
Parameter Selection
Number of Fields
SS
Default (01)
SS
01-10
Option Code FIN (2 digits)
Scan 2 digits from the option code chart in Appendix, then FuzzyScan will terminate this selection automatically.
(for MBC-6000 Series Only) Field Delimiter
TAB (09H) as the default delimiter MS
(for MBC-6000 Series Only) Record Delimiter
User defined character (1 character)
00-7F
CR (0DH) as the default delimiter MS
User defined character (1 character)
00-7F
(for MBC-6000 Series Only) For MBC-6000 setup process, you will need to read END and FIN to terminate the selection in stead of just reading END. User may select desired delimiter via reading ASCII codes of each delimiter according to ASCII code table in the Appendix section in page A-3.
2-24
Configure Your FuzzyScan
Condensed DataWizard ♦ Preamble, Postamble, Data Length & Symbol ID Trans. ♦ PROGRAM
M_DEFAULT
Family Code Selection
P.C.
Parameter Selection
Option Code
Data Length Transmission
SS
Disable
0
SS
Enable 2-digits data length transmission
1
If data length exceeds 99, 3-digit data length will be transmitted.
Symbology ID Transmission
Data Pass Control
SS
Disable symbol ID transmission
0
SS
Enable prefix symbol ID transmission
1
SS
Enable suffix symbol ID transmission
2
SS
Enable both prefix and suffix symbol ID transmission
3
SS
Disable (format match required)
0
SS
Enable (format match not required)
1
If data verifier is false, the original scanned bar code data will be transmitted.
Data Sequence Control
SS
Data output to host: Data Length first, then followed by Prefix Symbol ID
0
SS
Data output to host: Prefix Symbol ID first, then followed by Data Length
1
DataWizard is a very powerful, Artificial-Intelligence based data editing expert system provided specially for the FuzzyScan family bar code scanners. Through the DataWizard, you can process the scanned data prior the transmissions in many ways, such as: Insert, Delete, Match, Verify, Replace, Reorganize, and Repeat Transmission. It also allows you to arrange the transmission of scanned data to any specific format without software modification. Due to the resources used by this system, Full-feature DataWizard is only supported by PowerTool and not available on the FuzzyScan Lite series. Through the PowerTool, all settings and configurations can be done on-screen, under Windows 95/98/NT environment. To make the Preamble and Postable setting, please refer to the Keyboard Interface Control in page 2-20, or Serial Interface Control in page 2-22 for details. A Condensed Version DataWizard is provided for all FuzzyScan scanner including Lite series and is utilized by scanning the programming bar codes. When Data Pass Control is disabled, all input data must conform to an edited format or the scanner does not transmit the input data to the host. To make the Data Sequence Control setting, you can refer to the Keyboard Interface Message String in page 2-19, or Serial Interface Message String in page 2-22 for details.
2-25
Configure Your FuzzyScan
Condensed DataWizard ♦ Data Formater Setting ♦ PROGRAM
M_DEFAULT
Family Code Selection
P.C.
Formatter Control
SS
Disable
MS
Select one bar code symbology
(2 digits)
MS
Select all bar code symbologies
00
SS
Disable
FIN
DS
Enable
(2 digits)
1st Insertion
Parameter Selection
SS
Disable
FIN
Enable
(2 digits)
4th Insertion
SS
Disable
FIN
Enable
(2 digits)
[1-3 characters], [FIN]
[1-3 characters], [FIN]
position
SS
Disable
FIN
DS
Enable
(2 digits)
2-digits identified position; max. 3 insertion characters
[1-3 characters], [FIN]
position
DS
2-digits identified position; max. 3 insertion characters
automatic termination automatic termination
position
DS
2-digits identified position; max. 3 insertion characters
3rd Insertion
2nd Option Code
FIN
2-digits identified position; max. 3 insertion characters
2nd Insertion
Option Code
[1-3 characters], [FIN]
position
The Data Formatter is used to edit the scanned raw data prior to transmitting the data to the host computers or terminals. It allows you to select desired bar code symbologies for formatter control, and provides Multiple Position Insertion and Multiple Character Insertion (max three characters) in the identified position. While the Data Formatter is enabled, it arranges only scanned data without Preamble, Postamble, STX, ETX, Data Length, Prefix/Suffix Symbolology ID or Record Suffix. All of the above programmable parameters perform the same function depending on your setting. Regarding the “Bar Code Selection” and “Position Calculation” of data formatter, please refer to page 2-33 for details. Please note that all “Character” input should be referred to the ASCII/HEX Table listed in Appendix to find matched HEX value.
2-26
Configure Your FuzzyScan
Condensed DataWizard ♦ Data Verifier Setting ♦ PROGRAM
M_DEFAULT
Family Code Selection
P.C.
Verifier Control
SS
Disable
MS
Select one bar code symbology
(2 digits)
automatic termination
MS
Select all bar code symbologies
00
automatic termination
SS
Disable
FIN
MS
Enable
(2 digits)
Identified Data Length
Parameter Selection
Option Code
2nd Option Code
FIN
Determine the identified data length for verification.
1st Identified Character
SS
Disable
FIN
DS
Enable
(2 digits)
2-digits checking position; 1 identified character
2nd Identified Character
3rd Identified Character
position
SS
Disable
FIN
DS
Enable
(2 digits)
2-digits checking position; 1 identified character
[00-7F]
position
SS
Disable
FIN
DS
Enable
(2 digits)
2-digits checking position; 1 identified character
[00-7F]
[00-7F]
position
The Data Verifier is used to provide advanced verification for error-free scanning and to work as an Embedded Data Transmitting Filter. All data must conform to the Identified Bar Code Symbologies, Identified Data Length, and one to three Identified Characters in the checking position. Otherwise, the FuzzyScan will not transmit the data to the host computers or terminals, but will instead issue 3 long beeps for verification error and skip the scanned data. The Data Verifier checks only scanned data without Preamble, Postamble, STX, ETX, Data Length, Prefix/Suffix Symbology ID or Record Suffix. Regarding the “Bar Code Selection” and “Position Calculation” of Data Verifier, please refer to page page 2-33 for details. Please note that all “Character” input should be referred to the ASCII/HEX Table listed in Appendix to find matched HEX value. 2-27
Configure Your FuzzyScan
Condensed DataWizard ♦ Data Replacer Setting ♦ PROGRAM
M_DEFAULT
Family Code Selection
P.C.
Replacer Control
SS
Disable
MS
Select one bar code symbology
(2 digits)
automatic termination
MS
Select all bar code symbologies
00
automatic termination
SS
Disable
FIN
DS
Enable
(2 digits)
1st Replacement
Parameter Selection
Disable
FIN
DS
Enable
(2 digits)
[ 00-7F ]
position
SS
Disable
FIN
DS
Enable
(2 digits)
2-digits identified position; 1 replacement character
[ 00-7F ]
position
SS
2-digits identified position; 1 replacement character
3rd Replacement
2nd Option Code
FIN
2-digits identified position; 1 replacement character
2nd Replacement
Option Code
[ 00-7F ]
position
The Data Replacer is used to edit the scanned raw data prior to transmitting the data to the host computers or terminals. It allows you to select desired bar code symbologies for replacer control, and provides Multiple Position Replcement in the identified position. All data must conform to the Identified Bar Code Symbologies, and one to three Identified Characters in the identified position While the Data Replacer is enabled, it arranges only scanned data without Preamble, Postamble, STX, ETX, Data Length, Prefix/Suffix Symbology ID or Record Suffix. Regarding the “Bar Code Selection” and “Position Calculation” of Data Replacer, please refer to page 2-33 for details. Please note that all “Character” input should be referred to the ASCII/HEX Table listed in Appendix to find mathced HEX value.
2-28
Configure Your FuzzyScan
Condensed DataWizard ♦ Data Organizer Setting ♦ PROGRAM
M_DEFAULT
Family Code Selection
P.C.
Organizer Control
SS
Disable
MS
Select one bar code symbology
(2 digits)
automatic termination
MS
Select all bar code symbologies
00
automatic termination
SS
Disable
FIN
DS
Enable
(2 digits)
2-digits identified position; Forward/backward data transmission setting
position direction
1st Organization
2nd Organization
Include/Exclude Control
Parameter Selection
Option Code
2nd Option Code
FIN
SS
Disable
FIN
DS
Enable
(2 digits)
2-digits identified position; Forward/backward data transmission setting
position direction
SS
Transmitted data excluded the data of identified position
0
DS
Transmitted data included the data of identified position
1
0 (Forward) 1 (Backward)
0 (Forward) 1 (Backward)
The Data Organizer is used to edit the scanned raw data prior to transmitting the data to the host computers or terminals. It allows you to select desired bar code symbologies for organizer control, and provides maximum two identified positions to send the data forward or backward. It also allows you to control the transmitted data including or excluding the data of identification position. Please refer to the application example listed in page 2-33 for details. While the Data Organizer is enabled, it arranges only scanned data without Preamble, Postamble, STX, ETX, Data Length, Prefix/Suffix Symbology ID or Record Suffix. Reagrding the “Bar Code Selection” and “Position Calculation” of Data Organizer, please refer to page 2-33 for details. Please note that all “Character” input should be referred to the ASCII/HEX Table listed in Appendix.
2-29
Configure Your FuzzyScan
Select a Bar Code Symbology
Application Example
You can select one or all types of bar code symbologies to use Condensed DataWizard for advanced transmission arrangement. If you scan “00” to select all types, the FuzzyScan will arrange all incoming data to meet your pre-defined format. If you want to select only one type bar code, please select one of the option code listed below.
If your bar code label is a 16-digit Interleaved 2 of 5 which includes the information of 6-digit date code, 6-digit serial number and 4-digit unit price, you want the FuzzyScan do the following for you without software modification:
UPC-E : 03 UPC-A : 02 EAN/CAN/JAN-8 : 05 EAN/CAN/JAN-13 : 04 Code 32 : 07
Telepen : 13 Code 128 : 01 UCC/EAN 128 : 01 Code 39 : 07 Code 93 : 09
Apply only Interleaved 2 of 5 to the condensed DataWizard. Check bar code is actually with 16-digit length.
Codabar/NW-7 : 06 Code 25 Family : 08 Code 11 : 10 UK/Plessey : 12 MSI/Plessey : 11
Allow bar code output whose date code is leading with “9”. Three outputs with “TAB” suffix. The date code output should skip “9” and replaced it by “A”. The serial number output should be led with “SN”.
Position Calculation
The unit price output should be skipped the first 2 digits.
[Data Formatter]
Test Bar Code : 9 8 1 0 2 5 1 2 3 4 5 6 9 8 7 6
If there is a 5-character input data string, refer to the following to calculate the actual position for insertion: X 00
X 01
X 02
X 03
Actual Output : A81025[TAB]SN123456[TAB]76[TAB]
Programming Procedure
X 04
[Data Verifier]
05
[Data Verifier, Data Replacer, Data Organizer]
Scan “Program” to enter the programming mode.
If there is a 11-character data string, please refer to the following to calculate the actual position for identification.
Scan “Verifier Control” and set bar code symbology to “08” (Interleaved 2 of 5).
X
X
X
X
X
X
X
X
X
X
X
Scan “Identified Data Length” and set the length to “16”.
00
01
02
03
04
05
06
07
08
09
10
Scan “1st Identified Character” and set the identified position to “00”, then set the identified character to “39” (Hex Code of 9). 2-30
Configure Your FuzzyScan
[Data Formatter]
[Important Notice]
Scan “Formatter Control” and set bar code symbology to “08”.
Please note that Condensed DataWizard will follow the preset working flow as below:
Scan 1st Insertion” and set the identified position to “06”, then inserted characters to “09” (Hex Code of TAB), “53” (Hex Code of S), “4E” (Hex Code of N).
Verifier
Formatter
Replacer
Organizer
So when you set the identified position in Data Organizer, you must consider the inserted data which you already set via Data Formatter.
Scan “2nd Insertion” and set the identified position to “12”, then inserted character to “09”. In the final, you must scan “FIN” (Finish) code to terminate this selection. Scan “3rd Insertion” and set the identified position to “16”, then inserted character to “09”. In the final, you must scan “FIN” (Finish) code to terminate this selection. [Data Replacer] Scan “Replacer Control” and set bar code symbology to “08”. Scan “1st Replacement” and set the identified position to “00”, then replaced character to “41” (Hex Code of A). [Data Organizer] Scan “Organizer Control” and set bar code symbology to “08”. Scan “1st Organization” and set the identified position to “16”, then set the data transmission to “0” (forward). Scan “2nd Organization” and set the identified position to “17”, then set the data transmission to “1” (backward). Scan “END” (Exit) to terminate the programming.
2-31
Appendix
Appendix This chapter gives the most up-to-date description of the Keyboard Function Code Table, ASCII Input Shortcut for all FuzzyScan family programming use.
A Series of Intelligent Bar Code Reader with NeuroFuzzy Decoding
Also, all necessary bar code commands are printed in the foldout of the back cover of this manual. Please take special care on those pages for future programming purpose. If those pages are lost or damaged, please ask your local vendor for help. For accessory updated information, please consult with your local FuzzyScan vendor or visit our web site at: http://www.cino.com.tw
© Copyright 1999 PC Worth Int’l Co., Ltd. © Copyright 1999 Cino Group
A-1
Appendix
Keyboard Function Code Table No.
ANSI
ASCII
00
NUL
00H
01
SOH
02
Key Function
No.
ANSI
ASCII
Key Function
RESERVED
16
DLE
10H
F7
01H
CTRL (Left)
17
DC1
11H
F8
STX
02H
ALT (Left)
18
DC2
12H
F9
03
ETX
03H
SHIFT
19
DC3
13H
F10
04
EOT
04H
CAPS LOCK
20
DC4
14H
CTRL (Right)
05
ENQ
05H
NUM LOCK
21
NAK
15H
ALT (Right)
06
ACK
06H
ESC
22
SYN
16H
INS (Insert)
07
BEL
07H
F1
23
ETB
17H
DEL (Delete)
08
BS
08H
+ (Numeric Pad)
24
CAN
18H
HOME
09
HT
09H
TAB
25
EM
19H
END
10
LF
0AH
F2
26
SUB
1AH
PAGE UP
11
VT
0BH
F3
27
ESC
1BH
PAGE DOWN
12
FF
0CH
F4
28
FS
1CH
UP
13
CR
0DH
ENTER (Carriage Return)
29
GS
1DH
DOWN
14
SO
0EH
F5
30
RS
1EH
LEFT
15
SI
0FH
F6
31
US
1FH
RIGHT
To emulate the key functions above, program the scanner by using the corresponding ASCII hex value and also Enable the “Function Key Emulation”. For example, If you want to program in a suffix of a TAB, you would follow the directions for programming a suffix on page 2-20. For option code, scan “09” for a TAB. For some of the above key functions to work correctly, it is necessary to disable the NumLock key. A-2
Appendix
ASCII Input Shortcut HEX/ASCII Reference Table
To configure the user definable parameters of FuzzyScan via programming menu, FuzzyScan will ask you to scan your desired ASCII value in HEX form. You have to refer to the “HEX/ASCII Table” for details.
0
1
2
3
4
5
6
7
0
NUL
DLE
SPACE
0
@
P
`
p
1
SOH
DC1
!
1
A
Q
a
q
2
STX
DC2
"
2
B
R
b
r
3
ETX
DC3
#
3
C
S
c
s
4
EOT
DC4
$
4
D
T
d
t
5
ENQ
NAK
%
5
E
U
e
u
6
ACK
SYN
&
6
F
V
f
v
7
BEL
ETB
'
7
G
W
g
w
8
BS
CAN
(
8
H
X
h
x
9
HT
EM
)
9
I
Y
i
y
Refer to the Hex/ASCII Table, you will find the HEX value of “$” is 24.
A
LF
SUB
*
:
J
Z
j
z
B
VT
ESC
+
;
K
[
k
{
Scan the option code – 2 listed on the fold out back cover.
C
FF
FS
,
<
L
\
l
|
D
CR
GS
-
=
M
]
m
}
E
SO
RS
.
>
N
^
n
~
F
SI
US
/
?
O
_
o
DEL
Example: If you want the scanned data output leading with a Dollar Sign, you have to set the “Preamble” to “$”. The configuration procedure is listed below for reference. Scan the system command – PROGRAM listed on page 2-20 to enter programming mode. Scan family code – PREAMBLE to select this family.
Scan the option code – 4 listed on the fold out back cover. Scan the system command – FIN (Finish) to terminate Preamble setting.
Example : ASCII “A” → HEX “41”; ASCII “a” → “61” : High Byte of HEX Value : Low Byte of HEX Value
Scan the system command – End to exit the programming mode for normal operation.
A-3
Appendix
Bar Code Command List 001
011 1
002 2
014
015 5
007
Paging
023
033
024
034
043
044
025
035
045
026
036
046
Factory Default Setting
Keyboard Replacement
Uninstall
PowerTool Host Link
F
6
042
PC/AT, PS/2 Keyboard Wedge
E 016
041 System Information List
D
4
006
032
C
3
005
022 B
013
004
031
A 012
003
021
RS-232 Serial Interface
Pair Mode
017
027
037
047
018
028
038
048
029
039
049
030
040
050
7 008
009
019 9
010
FIN (Finish) 020
0
USB Keyboard Interface
PROGRAM
8
END (Exit)
USB Serial Interface
A-4
Appendix Bar Code Command List C01
051
Host Interface Selection
052
for Gold/Jade/Diamond Host Interface Selection
061
PROGRAM C02
071 Code 11 Min. Length
Codabar Min. Length 062
FIN (Finish)
081
072 Codabar Max. Length
Code128/EAN-128 Max.Length 082 UK/Plessey Setting
Code 11 Max. Length
for Jade & Diamond C03
053 END (Exit)
063 Symbol ID : 1 character
C04
054
C05
055
C06
056
UPC Family Setting 064
Symbol ID : 2 character
System Information List
C08
058 Factory Default Setting
C09
C10
060 PowerTool Host Link
MSI/Plessey Max. Length
Keyboard Layout 089
Code128/EAN-128 Setting
German Postal Setting 080
A-5
Telepen Max. Length 088
079
Code 11 Setting
Telepen Min. Length 087
MSI/Plessey Min. Length
Code 25 Max. Length
060 Codabar Setting
MSI/Plessey Setting
078
069 Code 39 Max. Length
086
077 Code 25 Min. Length
Code 39 Min. Length
Telepen Setting
Code 93 Max. Length
Code 25 Setting
068
059
085
076
067
UK/Plessey Max. Length
Code 93 Min. Length
IATA Setting
Code 39 Family Setting
084
075
066
UK/Plessey Min. Length
Code 93 Setting
EAN/CAN/JAN Setting
Readable Symbology Setting 057
083
074
065 Symbology ID Transmission
C07
073
Record Suffix 090
Code128/EAN-128 Min.Length
Preamble
Appendix Bar Code Command List C01
091 Postamble
PROGRAM C02
101
092
Preamble 102
Character Frame Control
FIN (Finish) C03
093
094
C05
095
C06
096
OCIA Output Format
Baud Rate (BPS)
Data Length Transmission 124 Symbology ID Transmission
Operation Mode 115
Data Frame 106
Dollar Sign Control 123
114
105
Function Key Emulation
System Information List
Code 39 Emulation
Handshaking Protocol
Caps Lock Control
122
113
104
Inverse Bar Code Reading
Narrow/Wide Ratio
Postamble
Intercharacter Delay
121
112
103 Intermessage Delay
END (Exit) C04
111
116
125 Buzzer Tone Adjust Scanning Tolerance
Data Pass Control 126 Data Sequence Control
Time Out Control (Printing Quality Control)
C07
097
C08
098
107 Key Pad Emulation
099
C10
100 PowerTool Host Link
118
119 Margin Time
110 Record Suffix
A-6
Formatter Control 129
Auto Power Off Duration 120
Module Time
Formatter Control 128
Redundancy (Scan Voting)
Initial Signal State 109
STX/ETX Control
127 Double Scan Verification
Output Polarity 108
Upper/Lower Case
Factory Default Setting C09
117
1st Insertion 130
Pulse Driven Duty
2nd Insertion
Appendix
Bar Code Command List C01
131 PROGRAM
C02
151
171
162
172
163
173
164
174
165
175
156
166
176
157
167
177
158
168
178
159
169
179
160
170
180
3rd Insertion 132
FIN (Finish) C03
161 3rd Replacement
152 4th Insertion
133 END (Exit)
Organizer Control 153
Verifier Control
C04
134
C05
135
C06
136
1st Organization 154
Identified Data Length
2nd Organization 155
1st Identified Character
Include/Exclude Control
2nd Identified Character
System Information List C07
137
C08
138
3rd Identified Character
Factory Default Setting
Replacer Control
C09
139
C10
140
1st Replacement
PowerTool Host Link
2nd Replacement
A-7
Appendix
Bar Code Command List C01
131
Digital I/O Output
Control (for FBC-8000 Series Only)
141
PROGRAM C02
132
Pulse Interval Control
133
Operation Mode
C04
134
Clear Memory
C05
135
Data Memory Upload
C06
136
Number of Fields
C07
137
Field Delimiter
C08
138
Record Delimiter
(for FBC-8000 Series Only)
142
FIN (Finish) C03
(for MBC-6870 Series Only)
143
END (Exit) (for MBC-6870 Series Only)
(for MBC-6870 Series Only)
(for MBC-6870 Series Only)
144
145
146
System Information List (for MBC-6870 Series Only)
(for MBC-6870 Series Only)
147
148
Factory Default Setting C09
139
149
C10
140
150
PowerTool Host Link
A-8
Appendix
Bar Code Command Menu Option Code : “0 – 9”, “A – F”
0
1
4
5
System Command
C
8
D
9
FIN (Finish)
END (Exit) (System List)
2
6
E
A
SYSLIST (Master Default)
3
7
F
B
A-9
M_DEFAULT
Appendix
Bar Code System Command To scan following commands will reset related settings to factory default, which may be different to your current settings. Please consult the technical person in charge of scanning or your local supplier before scanning the following bar codes.
PC/AT, PS/2 Keyboard Wedge Quick Set Command
Keyboard Replacement Quick Set Command System Information List (SYSLIST)
RS-232 Serial Interface Quick Set Command
Paging Command
Factory Default Setting (M_DEFAULT) USB Keyboard Interface Quick Set Command
USB Serial Interface Quick Set Command
Uninstall Command
FuzzyScan PowerTool Host Link Command Pair Mode Command
A-10
