Transcript
Doc. 02.34.00
TOYOTA
PIO / DIO Rev. C
Camry
2012 -
12/16/11
Keyless Entry System
Part Number: 00016-32901 Accessory Code: KE10
Conflicts
Color Applicability/Trim Level Accessory Color
NOTE: Not for installation on vehilce's equipped with factory installed keyless entry.
General Applicability
Vehicle/Trim Color
Power door locks required
Recommended Sequence of Events
Kit Contents
Item # Quantity Reqd 1 1 2 1 3 1 4 1 5 2 6 2 7 1
Description Keyless Module Main Harness Hardware Bag Valet Switch 24" Cable Ties 3-Button Transmitter Owner's Card
Item #
Accessory
Vehicle Service Parts (may be required for reassembly) 00016-79200-01 00016-34030-05 00016-32901-01 00016-30960-56 00016-32901-02 00016-30960-09
1 Keyless Entry Control Module 2 Keyless Entry Transmitter 1 Main Wiring Harness 1 On/Off Toggle Control Switch 1 Miscellaneous Hardware Kit 1 34" Headlight Extension Wire
Hardware Bag Contents Item # Quantity Reqd 1 8 2 8 3 2 4 6 5 1 6 1
Description Red T-Taps Black T-Taps Blue T-Taps 8" Cable Ties 2-1/4"x 2-1/4" Foam Pad Yellow T-Tap
Legend
Recommended Tools Safety Tools Special Tools INSTALLATION TOOLS Phillip screwdriver Ratchet w/extension Diagonal wire cutters Flashlight Torque Wrench
Straight-Slot screwdriver 10 mm socket Common pliers Nylon trim tool 48" lbs
S
STOP: Damage to the vehicle may occur. Do not proceed until process has been complied with. OPERATOR SAFETY: Use caution to avoid risk of injury. CRITICAL PROCESS: Proceed with caution to ensure a quality installation. These points will be audited on a completed vehicle installation. TOOLS & EQUIPTMENT: This calls out the specific tools and equipment required for this process. REVISION MARK: This mark highlights a change in installation with respect to previous issue. SAFETY TORQUE: This mark indicates that torque is related to safety.
SPECIAL NOTE: After TMS and Safety mandated preparatory steps have been taken, the installation sequence is the suggested method for completing the accessory installation. In some instances the suggested sequence is written for one associate to install and in others the sequence is given as part of a team accessory installation. Unless otherwise stated in the document, the associates may perform the installation steps in any order to make the installation as efficient as possible while maintaining consistent quality.
Special Chemicals
Southeast Toyota Distributors, LLC
* Mandatory
1 of 10
TOYOTA CAMRY
KEYLESS ENTRY SYSTEM Negative Battery
INSTALLATION PREPARATION Before starting installation 1. Familiarize yourself with the installation instructions. 2. Inspect kit components (Refer to kit contents and hardware bag contents).
PLASTIC NUT
VEHICLE PREPARATION
1. Place protective coverings on vehicle. 2. "IMPORTANT........IMPORTANT" Disconnect Negative Battery Cable REMOVE THE DRIVER'S SIDE KICK PANEL: 1. Refer to the vehicle repair manual, and carefully remove front kick panel.
REMOVE THE DRIVER'S SIDE SCUFF PLATE: 1. Refer to the vehicle repair manual, and carefully remove front scuff plate.
REMOVE THE SIDE DASH PANEL: 1. Refer to the vehicle repair manual, and carefully remove the driver's side dash finish panel.
Southeast Toyota Distributors, LLC
Page 2 of 10
TOYOTA CAMRY
KEYLESS ENTRY SYSTEM
PREPARING FOR INSTALLATION REMOVE THE LOWER FINISH PANEL: 1. Remove (1) 10mm bolt and (1) phillips screw from the driver's side lower finish panel. 2. Disengage the hood release cable from the hood release latch handle. 3. Carefully pull the lower finish panel outward from the vehicle dash to disengage the snap clips holding it place, then set the panel aside where it will not be damaged.
HOOD RELEASE 10mm BOLT
REMOVE THE LOWER CRASH SHIELD: This Step Is Optional 1. Remove (4) 10mm bolts from the driver's lower crash shield. 2. Place a protective cover on the driver's floor area, and wrap the metal crash shield with a cover to prevent scratching before moving it to the side.
REMOVE THE STEERING WHEEL SHROUD: 1. Remove the (2) phillip screws from the lower steering column cover. 2. Carefully dislodge the steering column cover tabs and remove the lower cover.
Southeast Toyota Distributors, LLC
Page 3 of 10
PHILLIPS SCREW
TOYOTA CAMRY
KEYLESS ENTRY SYSTEM
MODULE PREPARATION 1. Secure the antenna to the back side of the module, using a supplied foam pad. 2. Route the antenna and secure to the main harness with (2) cable ties. "IMPORTANT........Failure to route the antenna cable as described will result in reduced range of the system.
Cable Ties Foam Pad
INSTALLATION PROCEDURES MOUNTING MAIN CONTROL MODULE: 1. Secure the module to the dash brace at the far left end to the left of the driver side JB, using the long cable ties and adhesive pad provided in the hardware bag. NOTE: Guide long cable through the module eyelets as shown. DO NOT WRAP OR BUNDLE ANTENNA HARNESS. Module antenna wire must extend as high up as possible and secured in place for best signal. After Mounting Module
Before Mounting Module
Southeast Toyota Distributors, LLC
Page 4 of 10
TOYOTA CAMRY
KEYLESS ENTRY SYSTEM
INSTALLATION PROCEDURES MOUNTING THE TOGGLE SWITCH: 1. Install the ON/OFF bezel and nut. Tighten nut with care, do not over torque the nut. 2. Tie wrap to main harness loom in driver's kick panel directly besides the A3 ground lug as shown. NOTE: Toggle switch must be in the "OFF" position.
SECURING MODULE GROUND: 1. Secure the keyless entry system black ground wire to the left hand 10mm bolt securing the crash knee air bag. 2. Torque the 10mm bolt to 7ft. lbs. This Step is Optional 1. Remove (4) 10mm bolts from driver’s lower crash shield. 2. Place a protective cover on the driver’s floor area & wrap the metal crash shield with a cover to prevent scratching before moving it to the side. S
Note: If lower crash shield is removed the 4 bolts must bere-installed and torqued at 7 ft. lbs Use the torque sequence below.
Ground Location
2
1
3
4
T-TAP INSTALLATION: A. When installing female T - Tap connectors, be sure the wire is located inside the wire channel of the female T - Tap connector before closing connector over the wire with pliers. T - Tap
Step A
Wire from main keyless harness
Step B
IMPORTANT ! After installation, inspect & insure that all Keyless System Harness are clear of all HOT, SHARP or MOVING objects
Southeast Toyota Distributors, LLC
Page 5 of 10
Step C
Southeast Toyota Distributors, LLC
Page 6 of 10
PINK/WHITE [Driver's Unlock Detect Switch]: Use a black T-Tap and connect to the VIOLET wire in connector KI1, location 16.
PINK/WHITE [Driver's Unlock Switch]: Use a black T-Tap and connect to the GREEN** wire in connector KI1, location 11.
PINK [Driver's Lock Switch]: Use a black T-Tap and connect to the RED ** wire in connector KI1, location 10.
2 Pin Molex Connector - Plug into Toggle Control Switch.
BLUE/WHITE [ Driver Door Unlock Motor - Towards Body ECU] - (See Detail A)
WHITE [Driver Door Unlock Motor - Towards Door Lock] - (See Detail A)
Cut the GRAY WIRE in connector KI1, location 12. Strip the insulation from both sides of the cut wire, and crimp the WHITE WIRE from the keyless harness to the HARNESS side of the cut wire. Crimp the BLUE/WHITE WIRE from the keyless harness to the CONNECTOR side of the cut wire.
DETAIL "A" DRIVER'S DOOR UNLOCK CIRCUIT BLUE w/ WHITE
Cut & Strip Existing Wire WHITE
Harness Wires
YELLOW [ +12VDC Accessory]: Use a blue T-Tap and connect to the BLACK wire in connector I36, location 6.
RED [+12VDC Battery]: Use a yellow T-Tap and connect to the GREEN wire in connector I36, location 5.
BLUE WIRE [Headlighs]: Use black T-Tap and connect to the RED WIRE in connector I25, location 17.
WHITE WIRE [Tail Lights]: Use black T-Tap and connect to the BLACK WIRE in connector I25, location 18.
GREEN/RED WIRE [Horn]: Use red T-Tap and connect to the Lt. GREEN WIRE in connector I28, location 9.
CHASSIS GROUND - Connect the ring terminal to the left hand 10mm bolt securing the driver's crash knee airbag.
WIRING DIAGRAM
WIRING DIAGRAM CAMRY
CONNECTOR DETAILS: 1. CONNECTOR I36 : Ignition Switch
4. CONNECTOR I25 : Tailights
Location : Steering Column
Pin 5 Green +12V Battery
1
2
3
4
5
6
7
8
CAMRY Location : Combination Switch Connector
Black Connector
Pin 17 Red Head Lights Pin 6 Black +12V Accessory
1
2
3
4
5
6
7
8
Pin 18 Black Tail Lights
9 10
11 12 13 14 15 16 17 18 19 20
CAR Green Black
KEYLESS Red Yellow
CAR Red Black
2. CONNECTOR I28 : Horn
3. CONNECTOR KI1 : Door Locks
Location : Spiral Spring Connector Top Of Steering Column
Black Connector
Location : Driver's kick panel area Pin 11 Green Wire Door Unlock Switch
Pin 9 Lt. Green Horn
CAR Lt. Green
KEYLESS Blue White
Pin 12 Gray Wire Driver's Door Unlock Motor
KEYLESS Green/Red
Pin 10 Red Wire Door Lock Switch
CAR Red Green Gray Violet
Southeast Toyota Distributors, LLC
Page 7 of 10
Pin 16 Violet Wire Door Unlock Detect Switch
KEYLESS Pink Pink/White White & Blue/White Pink/White
COMPLETING THE INSTALLATION:
CAMRY
Torque the negative battery cable to 48” lbs.
ASSEMBLE ALL REMOVED PANELS TO THE VEHICLE: 1. Refer again to the vehicle repair manual and reassemble all panels that were removed for installation back onto the vehicle.Test thoroughly, all mechanical components disconnected and or removed from the vehicle during the installation of this accessory.
TESTING THE SYSTEM: 1. Prior to delivering the vehicle, test all features of the system accordinng to the owner's manual included. LOCK - Press and release the LOCK button on the transmitter. All doors should lock, headlights should come on. UNLOCK - Press and release the UNLOCK button on the transmitter. The driver's door should unlock, headlights should come on.
PREPARING THE VEHICLE FOR DELIVERY:
Press and release the UNLOCK button again. All doors should unlock.
1. To set the arm/disarm chirps to "soft" chirps. 2. Start with the doors in the unlocked position, Toggle Control Switch in the "OFF" position.
Press and hold the PANIC button. The horn should sound and the parkings lights should flash.
3. Turn the ignition key to the on position.
Press and release the PANIC button to silence the horn.
4. Turn the ignition key off, then immediately switch the Toggle Control Switch "ON" then "OFF" 4 times.
NOTE: Be sure to test both transmitter that were included in the kit.
5. The vehicle horn should respond with soft horn chirps. 6. Place the Owner’s Card in glove box.
Southeast Toyota Distributors, LLC
Page 8 of 10
COMPLETING THE INSTALLATION:
CAMRY
PROGRAMMING NEW or REPLACEMENT TRANSMITTERS TO THE SECURITY MODULE: IMPORTANT NOTE : Once you enter the programming mode, if 15 seconds elapse with no activity on the system, the programming mode will be terminated. If this happens, simply start over.
STEP 1
STEP 3
To get started, enter the vehicle and close all doors, then lock the doors by using the door lock switch mounted on the driver’s door panel.
Press and Hold the Lock button on the transmitter until the Driver’s Door Unlocks.
STEP 2
STEP 4 Lock all doors by using the door lock switch mounted on the driver’s door panel.
Turn the vehicle’s ignition key ON then OFF 7 times.....
STEP 5 Repeat Steps 3 and 4 for all transmitters that you need to program to operate the vehicle. (Maximum of 4 transmitters per vehicle)
STEP 6 When all transmitters have been programmed, turn the ignition key ON then OFF to exit the program mode. ....Ending in the OFF position.
Southeast Toyota Distributors, LLC
Page 9 of 10
TOYOTA CAMRY
KEYLESS ENTRY SYSTEM
VEHICLE FUNCTION CHECKLIST THESE POINTS MUST BE CHECKED TO ENSURE A QUALITY INSTALLATION Head Light If the warning lights remains on, it may indicate a system malfunction. High Beams
Massage Seats (if equipped) Power Side Mirrors (if equipped) Side Mirror Defogger (if equipped)
Turn Signal Lights Front Windshield Defogger (if equipped) Tail Lights Navigation System (if equipped) Stop Lights Rear Sunshade (if equipped) Backup Lights
Cruise Control Light (if equipped)
Hazard Lights
Steering Wheel Audio Control (if equipped)
Marker Lights
HVAC
Dome/Courtesy Lights
Power Locks (if equipped)
Panel/Switch Illumination Accessory Controls/Illumination (if equipped)
Power Windows (if equipped)
Rear Window Defogger (if equipped)
Gauges Front Wiper/Washer
Key Sensor Buzzer
Hood Latch Release
Fog Lights (if equipped) Day Time Running Lights (if equipped)
Passenger Air Bag Switch (if equipped)
Trunk/Tailgate/Bed Lights (if equipped)
Rollover Side Curtain Air Bag Switch (RSCA)
Glove Box Light (if equipped)
Horn
ABS Light (if equipped)
Seat Belt Warning Light If the warning lights remains on, it may indicate a system malfunction.
Rear Wiper/Washer (if equipped) Clock (if equipped)
Air Bag Warning Light If the warning lights remains on, it may indicate a system malfunction.
Accessory Power Socket (if equipped) Starter
Lamp Failure Sensor If the warning lights remains on, it may indicate a system malfunction. Track/Skid Control Light (if equipped)
Audio/Video (if equipped)
If the warning lights remains on, it may indicate a system malfunction. Tire Pressure Monitoring System (TPMS) Prior to TPMS activation and Pre-Delivery Service (PDS) of the vehicle the TPMS light will blink when IG is turned on. After TPMS activation and PDS of the vehicle the TPMS light will illuminate for a few seconds and go off when IG is turned on.
Power Sliding Door (if equipped) Convenience Memory Settings (if equipped) Heated (if equipped) Southeast Toyota Seats Distributors, LLC
Page 10 of 10
