Transcript
Rapid Conn
5016 SERIES ATA/66 & 100 Ribbon Cable Assemblies Double Ended (both facing same direction)
Note: For cables to function properly in ATA applications, the first connector should be the "Blue" connector. If using a two connector assembly, the second connector should be the "Black" connector. If a three connector cable is required all three "Blue, Gray & Black" connectors should be used in the proper order with "Blue" and "Black" on the ends with "Gray" in the middle.
Double Ended (one up, one down)
Multiple Connectors (all facing same direction)
Multiple Connectors (some up, others down)
Name
Company
Address City/State/Zip Phone
Fax
Connector Type
Number of Positions
Plating (circle one): 1.3µ Gold
5µ Gold
15µ Gold
30µ Gold (spl order)
Special Instructions
Custom Ribbon Cables Make your own cable by tracing over the example below (indicating up & down direction of each connector) filling in the necessary dimensions. Indicate which series connector and the number of pins, along with the plating type and thickness.
Fax or mail to the following:
RapidConn Inc. 19571 Pauling, Foothill Ranch, CA 92610-2606 949-951-1020 tel 949-951-8265 fax
Created by PDF Generator (http://www.alientools.com), to remove this mark, please register the software.
Rapid Conn
5016 SERIES ATA/66 & 100
The 5016 Series IDC Socket Connectors were designed to meet the requirements of SFF-8059 for use on SFF-8049 cable assemblies. Our products have been extensively tested and are in conformance with the listed specifications. The primary application for these cables is to connect ATA hard disk drives to the motherboard. In addition, these have been used where noise reduction or cross talk is a concern. Many applications may benefit from the G-S-G arrangement of the connectors and cables.
Created by PDF Generator (http://www.alientools.com), to remove this mark, please register the software.
5016 SERIES ATA/66 & 100 IDC SOCKET STRAIN RELIEF (P/N 5016-04-000) ORDERED SEPARATELY
.240 (6.10)
.415 (10.54) AFTER TERMINATION
.215
PIN 1 MARKER
.060 (1.52)
.025 (0.64) CONTACT TO GROUND PLANE .100 (2.54) CONTACT TO CONTACT WITHIN THE SAME ROW
EVN-GND
.050 (1.27) CONTACT TO CONTACT ROW TO ROW
Rapid Conn
WITH STRAIN RELIEF
.140 (3.56)
POLARIZATION KEY
PART NUMBER DESCRIPTION
2.180 (55.37)
5 01 6 - 1 0 X X
2.100 (53.34) .100 (2.54)
PIN 1 PLATING (MATING AREA) 0 - GOLD FLASH 1 - 15µ" GOLD 23 - GOLD FLASH OVER 30µ" PALLADIUM-NICKEL PIN 20 VOIDED
.100 (2.54)
5
PIN 40
1.900 (48.26)
CONNECTOR TYPE 0 - DEVICE "0" (BLACK INSULATOR) 1 - DEVICE "1" (GREY INSULATOR) 2 - SYSTEM BOARD (BLUE INSUALTOR) GROUND CONFIGURATION 0 - EVEN POLARIZATION 1 - MILITARY POLARIZATION
Notes: 1. Material: Insulator: Thermoplastic Polyester (PBT), 30% Glass Fiber Reinforced, U.L. Rated 94V-0 Color: See Part Number Description Cover and Strain Relief: Thermoplastic Polyester (PBT), 30% Glass Fiber Reinforced, U.L. Rated 94V-0 Color : Black Contacts and Ground Plane: Phosphor Bronze 2. Plating: Contacts: Selectively plated gold on mating area (see part number description), and 100µ" minimum tin/lead on IDC termination area, all over 50µ" minimum nickel underplate. Ground Plane: 100µ" minimum tin/lead on IDC termination area, all over 50µ" minimum nickel underplate. 3. Performance Specifications: Current Rating: Contact Resistance: Dielectric Withstanding Voltage: Insulation Resistance: Temperature Rating: Insertion Force: Separation Force:
1 amp per contact 20 milliohms maximum (initial) 10 milliohms maximum increase (during life) 600 VAC RMS 5000 megohms minimum. -55°C to +105°C 10oz. (199g) maximum (per contact) 1oz (28.4g) minimum (per contact)
4. This connector accepts 30 AWG ribbon cable (6645 Series) on .025 pitch. 5. Pin #20 is blocked on all connectors per specification. 6. Pin #34 on "System Board" connector is connected to ground only. Pin #28 on "Device 1" connector (grey) is removed.
Created by PDF Generator (http://www.alientools.com), to remove this mark, please register the software.
Rapid Conn
6145 Series .025 Pitch Ribbon Cable
DIM. "C" SIZE
80
INSULATION
DIM. "A"
DIM. "B"
TPO
2.000 REF.
PVC
2.000 REF.
DIM. "D"
STRANDED
SOLID
1.975 ± .007
.027 ± .002
.027 ± .002
.0125 ± .0050
1.975 ± .007
.027 ± .002
.027 ± .002
.0125 ± .0050
6145 - X X X X SERIES RIBBON CABLE .025 PITCH
NO. OF CONDUCTORS 50 68 80 REEL SIZE 1 - 100' 2 - 200' 3 - 300' 4 - 400' 5 - 500'
SOLID OR STRANDED (7/38) 30 AWG COPPER WIRE COLORED POLARITY STRIPE ON #1 CONDUCTOR
INSULATION/CONDUCTOR TYPE 2 - TPO, 30 AWG SOLID 3 - TPO, 30 AWG STRANDED (7/38) 4 - PVC, 30 AWG SOLID 5 - PVC, 30 AWG STRANDED (7/38)
"C" DIM.
"D" DIM.
.025 ±.002 TYP. "B" DIM. "A" DIM.
TP0 SPECIFICATIONS (INSULATION TYPES 2 AND 3)
PVC SPECIFICATIONS (INSULATION TYPES 4 AND 5)
1. Physical: Conductors:
1. Physical: Conductors:
Insulation: Pitch: Temperature Rating: Flammability Rating:
2. Electrical: Voltage Rating: Current Rating: Conductor Resistance: Impedance: Capacitance @ 1 mhz: Inductance @ 1 mhz: Propagation Delay:
3. UL and CSA Recognized
30 AWG (7/38) Stranded Tinned Copper 30 AWG Solid Bare Copper TPO, Cream with colored polarity stripe .025 ±.002 -40°C to +105C UL VW-1 CSA FT-1
150V 0.8 amps 106 ohms/1000ft (Stranded) 104 ohms/1000ft (Solid) 82 ohms (Stranded) 90 ohms (Solid) 15.7 pF/ft (Stranded) 15.5 pF/ft (Solid) .14µH/ft (Stranded) .15µH/ft (Solid) 1.44 ns/ft (Stranded) 1.45 ns/ft (Solid)
Insulation: Pitch: Temperature Rating: Flammability Rating:
2. Electrical: Voltage Rating: Current Rating: Conductor Resistance: Impedance: Capacitance @ 1 mhz: Inductance @ 1 mhz: Propagation Delay:
30 AWG (7/38) Stranded Tinned Copper 30 AWG Solid Bare Copper PVC, Gray with colored polarity stripe .025 ±.002 -40°C to +105C UL VW-1 CSA FT-1
150V 0.8 amps 106 ohms/1000ft (Stranded) 104 ohms/1000ft (Stranded) 75 ohms (Stranded) 80 ohms (Solid) 23.3 pF/ft (Stranded) 24.9 pF/ft (Solid) .14µH/ft (Stranded) .15µH/ft (Solid) 1.62 ns/ft (Stranded) 1.52 ns/ft (Stranded)
3. UL and CSA Recognized
Created by PDF Generator (http://www.alientools.com), to remove this mark, please register the software.
Created by PDF Generator (http://www.alientools.com), to remove this mark, please register the software.
