Transcript
DEC Installation and programming reference
Contact Ethernet Converter module Installation and programming reference
Features: • • • • • • • •
Encrypted Ethernet communication 24 hour , two way connection to the Monitoring Station 4 programmable and remotely controlled Open collector output Local programming by serial port or through Ethernet port Remote programing throug IP networks (Internet) Industrial signal transmission through serial port or throug contact inputs External security panel DTMF Contact ID conversion to Ethernet Web programming.
Page 1
www.skylaboratories.com
DEC Installation and programming reference
Page 2
www.skylaboratories.com
DEC Installation and programming reference
1.0. DEC module hardware description 1.1. Main parts:
1.2.2. Outputs: Max output load is 200mA per output Wiring of the outputs:
1.0.1. RS 232 connector: 1. 2. 3. 4. 5. 6.
Fixing holes Ethernet connector RS232 port Input terminals Output terminals Output status LEDs
Dec modules are available for serial communication for more information please contact your dealer or the manufacturer.
2.0. Specification:
1.1.1 Input terminals: + Positive 12 V DC GND Negativ Z1-Z4 Double EOL inputs 1.1.2 Terminal for the phone input and outputs. + O1-O4 Line Phone
Positive voltage for the outputs Open collector terminals Incoming PSTN line External device with communicator or telephone handset.
1.2.1. Inputs: Wiring of the inputs:
Input: Marking on the panel
Z1 Z2 Z3 Z4
Zone Number
EOL
Input 1 Input 2 Input 3 Input 4 Input 5 Input 6 Input 7 Input 8
2,2K 3,3K 2,2K 3,3K 2,2K 3,3K 2,2K 3,3K
Woltage: Max current consumption: Size of pcb (L x W x H) Size of terminals: RS 232 connector: Ethernet connector:
10-16 VDC 35mA (+OC) 133 x 68 x 19mm Ø2,5 mm Stand. 9 pins Stand. 8 pins
Kommunication: Outputs: Inputs: User name: Password: Factory network settings: Network mode: IP adress: Factory Port settings:
128 bit encrypted max. 200 mA 2,2 K vagy 3,3 K +/-10% Admin admin
Page 3
DHCP 192.168.254.253 8080
www.skylaboratories.com
DEC Installation and programming reference
3.0.
Installation of the board
4.1.2. LAN without DHCP server:
3.1.
Fixing and connection.
Us the fix, factory default IP address to connect to the panel. For this the computer with the browser must be ont he same internal network as the module. (192.168.254.1)
1. 2. 3. 4. 5. 6.
Fix the panel by the four fixing holes Connect the in and output wires. Connect Ethernet and Serial cable Check wires. Connect Power. Program the panel.
1.
Connect the computer directly or through Local Area Network (LAN) (direcctly connection with crosslink cable)
2.
Open an internet browser like Mozzilla Firefox or Internet Exprorer. Type into the browser field the IP address and port (192.168.254.254:8080)
3.
4. Configuring and checking the panel The panel has a built in web server, so it could be programmed by a standard web browser like Firefox or IE, there is no separate programming software. Remote access could be done through built in web server.
4.
If connection is successfull than you will see the following entry page. To enter, clock „Login”
5.
Type the factory default User name and Password
4.1. First connection to the panel: 4.1.1. LAN with DHCP server: The panel will search for DHCP server, if its not found, the panel will use the factory pre-set IP address. If the network is DHCP enabled CEC will obtain IP address and network settings. The IP address of CEC could be seen in a status window of the designated router of the network.
User Name: Password:
Admin admin
Exapmle:
6.
Page 4
After successull entry you will see the Status window :
www.skylaboratories.com
DEC Installation and programming reference
4.2. Programming: Change the factory setting by enter into Configure section.
• IP address: This is the several IP. This aress is used for remote programming or remote controlling. Factory default: 192.168.254.253 • Netmask: It is for to be able to distinguish between IP address and identification parts for IP packet receivers. Factory default: 255.255.255.0 • Gateway: This is a device which is in connection with more TCP/IP network. It is for routing and forwarding different IP packets between these networks. For example a router address within the network is designated to .gateway. Factory default: 0.0.0.0 • Nameserver: This is a name servert he server of the service provider. Write the provider server address into this field. ( A router could be also a name server) Factory default: 0.0.0.0
4.2.1. Network: This is the position where you may set network parameters. Next time you may connect the panel according to the parameters you type in.
• DTMF ID: DEC module is capaple to receive Contact ID codes from external security control panel. Here you can determine what to dial to send security panel reports through DEC module. In case of dial attempt from the external device the numbers matching the numbers the security panel dials than DEC sends Handshake signal and ready to receive CID codes. If the dialled and the pre-programmed number is not matching DEC will re-route the dialling attempt to the connected available PSTN line. PSTN lines should be connected to LINE inputs and standard phonesets and external control panel must be connected to the Phone output of DEC module. Factory default: 456
• Administrator password: The entry password could be changed here, max 16 character long password could be used Factory default: admin Warning: - If you loose your new password only manufacturer can reset the factory default password. If you mistype the password , you have 3 consecutive tries only, than the panel will not respond to it anymore. - This could be re-setted by power on-off procedure.
Warning: Choose telefon numbers does not interfere with other numbers dialled on the standard telco lines. .
• Network Mode: Choosing the network connection: Fix IP address Dynamic IP address Factory default: DHCP Note: If you use dynamic IP, its still advised to use one fix IP in case if DHCP service would be not available. In this case the module will change to Fix IP address.
Page 5
www.skylaboratories.com
DEC Installation and programming reference
4.2.2. Connection:
4.2.4. Outputs:
• #1 Server address: The IP address of the Monitoring Station. Please contact your Installer or Monitoring Station. Factory default: 0.0.0.0
• Output: Number of the output.
• #1 Server Port number: This is the port number of the IP address. Please contact your Installer or Monitoring Station. Factory default: 8080 • #1 Modul ID: It is an unique ID number to be used for routing module datas. Factory default: 1 • Az „#2” –vel jelölt szer: Secondary server parameters. Setting similar as above. • Test sign interval: The module is in continous connection with the monitoring station, but sends test signals in periodical time. Factory default: 120 sec 4.2.3. Inputs • Input: Number of the input. Figyelmeztetés: To program an input please refer to point 1.2.! • Enabled: The thickbox is to be used to disable inputs are not used. Enable input: The disable input: Factory default: all „Disable”
• Type: - Not used: If you do not need an output please select this one. This output can not be even activated remotely. - Communication Fail: If modul has disrupted communication this output will be activated. - Zone follower: It will be activated if the selected input is violated. You must consider the additional output settings for operation. - Server control: The server will control this output remotely. Factory default: all „Not used” • Mode: The timing of output operation is set here. - Monostabi: One state output. It will be activated and the time will follow the timing of the port than return to normal. - Inverse: This is an inverse operation. The output is always active than return to inactive for the duration of the pre-set output timing. - Bistable: This is a two state output. It will be switched to its on or off position according the trigger condition. The state of the output will remain in that particular state where its switched to. No timing on this kind of output. Factory default: all „Monostabile” • Timer: Steps of seconds as required to operate the output. Factory default: all „0”
Note: Disabled input does not have to be closed by an EOL resistor.
• Zone num.: If the output is a zone – input follower output select the particular output here. Factory default: all „Zone 1”
• Point Num.: Alarms of the port will be transmitted and identified with this 3 digit number. Factory default: all „0”
Note: The operation timing depends on output timing not the input alarm time. In case of Bi-Stable mode the output will follow timing of the selected input timing.
• Alarm CID: This code is to be sent in case of Alarm of the particular zone. Factory default: all „0”
4.2.5. „Save changes” button All changes must be saved to change operating parameters of the module.
• Restore CID: This code is to be sent in case of Restore of the particular zone. Factory default: all „0”
Note: By pressing this button the module will be re-started.
Note: In case of short circuiting input terminals both zone number belongs to this input will be sent as tamper alarm.
Page 6
www.skylaboratories.com
DEC Installation and programming reference
5.0. Status request and output remote controlling. The module could be found ont he IP address as pre-set in configuration page. 5.1. Status description
5.1.3.
Conecction
• Network status: The momentary status of the central station server. 5.1.4. Input/Otput Status of in and outputs • Input: Number of inputs • Status: Status if the momentary output condition. To see changes while browsing you should refresh the browser page. • Output: Number of outputs • State: Status if the momentary output condition. To see changes while browsing you should refresh the browser page. 5.2. Remote control of the outputs Output status could be changed by pressing the button near the output number. Change will be carried out immediately.
5.1.1.
Hardware Hardware datas
• Version: The software version of the module • Hardware ID: This is a factory pre-set, not changeable serial number of the module.
6. Contact If you click Contact you may send a pre-addressed message to the manufacturer Sky Laboratories. If you need further assistance please send us an e-mail or call us at numbers found on the installation manual.
• Uptime: The time since last re-start. 5.1.2.
Network Networki parameters
• Ethernet address: The MAC address of the panel. • Mode: The type of connection. • IP address: The IP address of the panel • Netmask: Network Identifier • Gateway: The Gateway IP address which is used to communicate to the server. • Nameserver: The server connection point or the the router itself. The module time is set by these devices.
Page 7
www.skylaboratories.com
DEC Installation and programming reference
6.0.
Serial programming:
4. Com Port Settings
If you lost IP address, password or other network parameter you may re-program the board by its serial port.
6.1.
Connect to the computer:
6.2.
Hyper Terminal settings:
1. Open the „Hyper terminal” program
- Select the following data: • Bit/sec : • Adat bites: • Paritas: • Stop bites: • Flow control:
2. Set connection.
115200 8 None 1 Hardware
- After select, please press Apply
6.3.
Programming:
6.3.1. Starting Hyper Terminal:
- Name the connection - Select Icon 3. Connection Direction
6.3.2. Connection: - Restart panel (disconnect and reconnect power) - Hit „Space”bar in 2 sec. - Password is admin
- Select com port
Page 8
www.skylaboratories.com
DEC Installation and programming reference
6.3.3. Config Settings:
6. Admin password:
0. Print config:
7. Save config:
1. MAC address.
8. Cancel: Cancel without saveing config. 9. HTTP port:
2. Network config: Warning : If you mistyped any new settings , repeate it from the begining before you hit „7” for reboot 3. IP address:
4. Netmask:
5. Gateway:
Page 9
www.skylaboratories.com
DEC Installation and programming reference
Availability:
Sky Laboratories Kft. Address: 2146 Mogyoród, Pf.: 16, Kerektó u. 2 Tel.: +36-28-542-250 Fax: +36-28-542-251 Email:
[email protected]
Page 10
www.skylaboratories.com
