Transcript
×NTINUUMª Enclosure and Display Module System The Continuum NEMA 1-style enclosure provides a convenient way to wall-mount an entire Continuum intelligent building system in a single location and is uniquely styled • NEMA 1-Style Enclosure for Wall-Mount Installation of
to match your Andover Controls Continuum product line. The enclosure makes initial
Entire Continuum Intelligent
installation and future change-outs of the Continuum modules quick and easy; provides
Building System
• Built-in DIN Rails for Easy
safety for technicians and protection from environmental elements; and offers convenient front door mounting of the Continuum LED and LCD local display modules.
Lock-in-Place Mounting of
Continuum CPU, Power
EASY MODULE INST ALLA TION INSTALLA ALLATION
Supply, and up to 10 I/O
The six-inch deep enclosure provides room to mount the Continuum NetController CPU, power supply, and up to ten
Modules
I/O modules on three built-in DIN rails. The DIN rails are attached to a removable steel back plate, which allows you to mount the actual enclosure separately from the Continuum modules. Simply hook each module onto the DIN
• Convienent Front Door
rail, plug the built-in power/communications connector on the left side of each module into the complimentary
Mounting of up to 9
connector on the right side of the previous module, and then snap-close the quick-release fasteners to lock the
Continuum Local Display
module in place on the rail. It’s that easy!
Modules
More I/O modules, if needed, can be located in additional Continuum enclosures. In addition, a single I/O module or • Durable Steel Welded Construction
groups of I/O modules can be located outside an enclosure, for example, to control a remote door or lighting system. All additional I/O modules are connected to the Continuum system using approved cable and an external 24VDC power supply.
• Built-in Cable Management Troughs Streamline and
ENCLOSURE DESIGN
Protect Wiring Runs
The enclosure’s welded design and rugged cold-rolled steel construction ensure durability. Vertical support bars on the inside of the cabinet door provide added rigidity and a built-in door lock guards against tampering. Cable management troughs underneath each DIN rail streamline and protect wiring runs. A bracket for two 12V 7.0 AHr sealed rechargeable batteries is provided at the bottom of the enclosure for UPS support.
FRONT DOOR DISPLAY AND CONTROL MODULES
The front door of the enclosure contains removable sections into which the Continuum display and control modules can be mounted. These modules—the LB-8 LED Bar Module, LS-8 LED 3-Digit Module, LC-1 2-Line Display with optional VM-1 Voice Module, and the GA-40/80 Graphic Annunciator Panels—are secured directly into the back of the door with screws and connected to the I/O bus by a five-conductor cable assembly. The Continuum system simply treats these display modules as additional I/O modules. Up to nine display modules can be mounted on the door. Mix various combinations of display modules to meet your specific operator interface needs. Alternately, the enclosure can be ordered with only three tinted Plexiglas panels in the door. This option allows you to view the status lights of all internal modules when the enclosure door is closed.
Technical Manuals Online! - http://www.tech-man.com
LB-8 LED BAR MODULE
• 8 user-programmable LED ON/OFF indicators • 8 user-programmable push-button digital inputs The LB-8 LED Bar Module provides a cost-effective way to view and modify your facility operation with 8 programmable LED indicators, each with its own programmable companion push-button with audible feedback. The LB-8 is an excellent choice for basic equipment status indication, ON/OFF control, and override capability. Programming the LED indicators and push-buttons is done with Andover Controls Plain English® programming language. Labels above each LED and companion push-button allow you to customize each I/O point.
LS-8 LED 3-DIGIT DISPLAY MODULE
• 8 user-programmable, 3-digit, 7-segment LED displays with floating decimal point • 8 user-programmable up/down arrow push-button digital inputs The LS-8 LED 3-Digit Display Module combines eight 3-digit 7-segment LED displays with 8 companion up/down arrow pushbuttons. Use the LEDs to display building parameters such as temperature, airflow, humidity, or occupancy status. The up/down arrow push-buttons with audible feedback allow an operator to turn equipment on and off, change set points, air balance VAV boxes, adjust override time, arm and disarm a security system, etc. Programming the LED displays and up/down push buttons is done with Andover Controls Plain English® programming language. Labels above each LED and companion push-button allow you to customize each I/O point.
LC-1 2-LINE DISPLAY
• 16 character by 2 line LCD display with backlighting • 12-button programmable keypad • Optional VM-1 Voice Module • Similar functionality to Infinity Infistat Display Interface The LC-1 Display Module features a 16 character by 2 line LCD display with backlighting and a 12-button ergonomically designed programmable keypad—up/down left/right arrows for LCD cursor control, Enter and Cancel push-buttons, and 6 userprogrammable functions keys. With one touch of a finger, you can scroll through building parameters such as temperatures or pressures, view equipment status, change setpoints and schedules, turn equipment on and off, or air balance VAV boxes. The keys can also be programmed to perform a wide variety of functions, including switching a specific zone to occupied mode, signaling an alarm condition, adjusting the amount of override time, arming and disarming a security system, and enforcing password security. Programming the display and function keys is done with Andover Controls Plain English® programming language. A label window above the six functions keys is provided. The LC-1 interfaces to the optional VM-1 Voice Module.
Technical Manuals Online! - http://www.tech-man.com
VM-1 VOICE MODULE
• Voice record and playback • On-board speaker • Microphone input • Audio output jack The VM-1 Voice Module provides local voice annunciation for your Continuum system. Operators can record and store approximately 100 custom messages (2 minutes maximum total record time) for playback. Use the VM-1 to annunciate alarm messages, provide audible instructions for critical applications, or broadcast messages over the building’s public address system via a built-in audio pre-amp level output signal. Pre-recorded messages can also be played back as a result of an event occurrence using a Plain English language program resident in the Continuum NetController. The VM-1 interfaces to the LC-1Display Module and mounts adjacent to it in the Continuum enclosure front door. Record/ playback control is provided via the LC-1 keypad/LCD display. The VM-1 features an on-board speaker with volume control, 1/8” jack microphone input, and a pre-amp level output and a built-in transitor for ON/OFF control of the PA channel during message playback.
GA-40/80 GRAPHIC ANNUNCIA TOR P ANEL ANNUNCIATOR PANEL
• Door-mounted “mimic panel” • Graphically represents 40 or 80 I/O points • Built-in interface to Continuum DM-20 modules • Pre-terminated LEDS and control switches provided • Optional firefighter controls for smoke management applications The Continuum GA-40/80 Graphic Annunciator Panel provides a convenient graphic representation of your building’s mechanical systems, ventilation systems, smoke control sequences, or other “mimic” panel applications. The GA-40/80 includes a backplate with holes for 40/80 status LEDs and control switches and mounts directly inside the door of the Continuum enclosure—you attach a graphic with predefined holes to the front of the door. LEDS are available in three color choices (red, yellow, green) and control switches are available in two lengths (0.5” and 1.0”) and two styles (flat blade and round). Connectors for both the LEDS and switches are provided and attach directly to the built-in terminal blocks for interface to one or more Continuum DM-20 I/O modules mounted on the enclosures’s DIN rail. The GA-40/80 accepts 24VDC from the DM-20 via a three-position cable assembly and converts it to 5VDC. Each DM-20 can provide power for up to 20 inputs or outputs. The Graphic Annunciator Panel can be configured to meet applicable fire department regulations and includes the required firefighter key switches, push-buttons, and annunciator. A GA-80 model, which supports up to 80 I/O points, is also available.
DIMENSION
DRAWING
36.0
24.0
Technical Manuals Online! - http://www.tech-man.com
ENCLOSURE
OPTIONS
ENCL-0DISP
ENCL-3DISP 3 Modules
ENCL-6DISP 6 Modules or 1 GA-40 with 1 Module
ENCL-9DISP 9 Modules or 1 GA-80
SPECIFICATIONS MECHANICAL
Size:
24.0” W x 36.0” H x 7.0” D (609.6 x 914.4 x 177.8 mm)
Weight:
75lbs (34.0kg))
Mounting:
Wall-mount with removable steel back plate
Material:
Base: 0.075” (1.90mm) thick cold-rolled steel Door Cover: GE Noryl Door Insert: GE Noryl
Andover Controls Corporation World Headquarters 300 Brickstone Square • Andover, Massachusetts 01810 USA Tel: 978 470 0555 • Fax: 978 470 0946 http://www.andovercontrols.com Andover Controls Ltd. Smisby Road • Ashby-de-la-Zouch • Leicestershire LE65 2UG, England Tel: 01530 417733 • Fax: 01530 415436 Andover Control GmbH Am Seerhein 8 • D-78467 Konstanz, Germany Tel: 07531 99370 • Fax: 07531 993710 Andover Control S.A. 93 Avenue de Fontainebleau • 94270 Le Kremlin-Bicetre, France Tel: 49 60 63 63 • Fax: 49 60 62 71 Andover Controls Corporation 707 Chinachem Golden Plaza • 77 Mody Road, Tsimshatsui East • Kowloon, Hong Kong Tel: 2739 5497 • Fax: 2739 7350 Copyright 1998, Andover Controls Corporation. Data subject to change without notice. All brand names, trademarks and registered trademarks are the property of their respective holders. Consult Andover Product Installation Guides for exact installation instructions and specifications. U.S. Patent #4591967 #DS-ENCLOSURE-A
Technical Manuals Online! - http://www.tech-man.com
