Transcript
the conversion technology experts FAST ETHERNET POINT SYSTEM SLIDE-IN-MODULE MEDIA CONVERTERS
POINT SYSTEM SLIDE-IN-MODULE MEDIA CONVERTERS FAST ETHERNET 100BASE-TX TO 100BASE-FX Features: CLASS B Round trip delay of only 40 bit times—far below the Class II rating of 92 bit times. AutoCross™ Technology AutoCross technology eliminates an entire category of network troubleshooting by automatically matching crossed and uncrossed cables to the appropriate connection. The twisted pair port is instantaneously configured to the correct MDI or MDI-X configuration. N-Way Auto-Negotiation Only Transition Networks guarantees compatibility with any 10/100-compliant port. This feature allows you to force the proper port configuration through an external switch on the converter; unlike competitive products that ship in auto-negotiation mode and may require both hardware and software configuration. Link Pass Through Automatically detects and reports loss of link on a connection using Link Pass Through. This feature allows the equipment at the remote end of a link failure to "see" this failure and respond with corrective actions, such as Spanning Tree fail-over links, proprietary trunking links, or failure reports through SNMP or RMON procedures built into the switch, router or hub.
Transition Networks, Inc. 6475 City West Parkway Minneapolis, MN 55344 USA
ORDERING INFO: CLASS B
Far End Fault (FEF) Detection Ensures that link failures are reported properly to all devices on the network so that network problems can be diagnosed and corrected quickly. (FEF) can be disabled when required. The converters will also automatically re-establish link when connected to two 10/100 auto-negotiating switches if link is lost. With other manufacturers’ converters the user must intervene to re-establish link. Pause Transition Networks conversion products will pass PAUSE signaling unhindered; allowing devices which are pause enabled to operate properly. Applications Deploy fiber in a strategic and economical manner by using Fast Ethernet converters. Fast Ethernet converters can extend distances that copper cannot reach.
Product Number
Port One
Port Two
CFETF1011-205
100BASE-TX (RJ-45)
100BASE-FX 1300nm MM (ST) 2 KM
CFETF1013-205
100BASE-TX (RJ-45)
100BASE-FX 1300nm MM (SC) 2 KM
CFETF1014-205
100BASE-TX (RJ-45)
100BASE-FX 1300nm SM (SC) 20 KM
CFETF1015-205
100BASE-TX (RJ-45)
100BASE-FX 1300nm SM (SC) 40 KM
CFETF1016-205
100BASE-TX (RJ-45)
100BASE-FX 1310nm SM (SC) 60 KM
CFETF1017-205
100BASE-TX (RJ-45)
100BASE-FX 1550nm SM (SC) 80 KM
CFETF1018-205
100BASE-TX (RJ-45)
100BASE-FX 1300nm MM (MT-RJ) 2 KM
see reverse for specifications
EXTEND NETWORK DISTANCE
tel 952.941.7600 or 800.526.9267 fax 952.941.2322
[email protected] http://www.transition.com
FAST ETHERNET POINT SYSTEM SLIDE-IN-MODULE MEDIA CONVERTERS
SPECIFICATIONS
SPECIFICATIONS
Standards
IEEE 802.3 1998
Unit LED
Power: Steady green LED indicates connection to external AC power
Connectors
1 RJ-45 (100 meters); 1 duplex fiber optic
Port LEDs
LKF (Fiber Link): Steady LED indicates fiber link connection; RXF (Fiber Receive): Flashing LED indicates data reception on fiber link; RXC (Copper Receive): Flashing LED indicates data reception on copper link; LKC (Copper Link): Steady LED indicates copper link connection
Dimensions
Width: 0.86" (22 mm) Depth: 5.0” (127 mm) Height: 3.4” (86 mm)
Power Consumption
3.4 watts
Fiber Optic Connector Specs CFETF1011-205 Min TX PWR: -19.0 dBm & CFETF1013-205 Max TX PWR: -14.0 dBm & CFETF1018-205 RX Sensitivity: -30.0 dBm Max In PWR: -14.0 dBm Link Budget: 11.0 dB CFETF1014-205
Min TX PWR: -15.0 dBm Max TX PWR: -8.0 dBm RX Sensitivity: -31.0 dBm Max In PWR: -8.0 dBm Link Budget: 16.0 dB
CFETF1015-205
Min TX PWR: -8.0 dBm Max TX PWR: -2.0 dBm RX Sensitivity: -34.0 dBm Max In PWR: -7.0 dBm Link Budget: 26.0 dB
Environment
See chassis specifications
Shipping Weight
1 lb. (.45 kg)
Compliance
UL Listed; C-UL Listed (Canada); CISPR/EN55022 Class A & B; FCC Class A & B; CE Mark
CFETF1016-205 Min TX PWR: -5.0 dBm & CFETF1017-205 Max TX PWR: 0.0 dBm RX Sensitivity: -34.0 dBm Max In PWR: -7.0 dBm Link Budget: 29.0 dB 3-position Jumper
4-position Switch
FCC & CISPR Class A devices comply with radiated emissions standards for commercial applications in the United States (FCC Class A) and Europe (CISPR Class A)
Hardware: Converter mode is determined by 4-position switch settings Software: Converter mode is determined by most recently saved onboard microprocessor settings. Pos 1 (UP) Advertises 100 Mb/s full-duplex/ half-duplex during auto-negotiation. (DOWN) (Used primarily when connecting to hub.) Operates at 100 Mb/s in duplex mode of attached device. Pos 2 Applies only if Switch 1 is UP AND media converter is connected to auto-negotiating device(s) capable of Pause Control Frame propagation. (UP) ALLOWS negotiation of Pause Control Frame. (DOWN) Does NOT allow negotiation of Pause Control Frame. Pos 3 (UP) Enables Link Pass-Through (DOWN) Disables Link Pass-Through. Pos 4 (UP) Enables Far-End Fault. (DOWN) Disables Far-End Fault.
FCC & CISPR Class B devices comply with radiated emissions standards for residential applications in the United States (FCC Class B) and Europe (CISPR Class B) Warranty
Lifetime
10/02 Technical information subject to change without notice.
make the necessary adaption while not affecting the performance, nature or appearance of the network to the users or devices.
Company Overview Transition Networks designs and manufacturers Conversion Technology products, specializing in media converters. These products help customers, such as AT&T, Internap, Lowes, and Chrysler, cost-effectively deploy fiber by reducing the costs of electronics as much as 40%. Due to the built-in reliability and management features of Transition's Point System Platform, customers can experience these cost savings without jeopardizing the availability of their fiber networks. Our principle of conversion technology is to
Transition Networks, Inc. 6475 City West Parkway Minneapolis, MN 55344 USA
Products Transition Networks develops and distributes media conversion tools that enable today's—and tomorrow's— bandwidth growth requirements. The company's products are designed to protect the investment made in network infrastructure while optimizing its performance capacity. Distribution Transition Networks distributes product exclusively through a network of resellers in North America and 50 countries worldwide. The company also supports key OEM partners that private label its products.
tel 952.941.7600 or 800.526.9267 fax 952.941.2322
[email protected] http://www.transition.com
