Transcript
Quick Guide
XX282-20-00
Surveyor® MKII Series Network Camera Domes Vicon Industries Inc.
Tel: 631-952-2288 Fax: 631-951-2288 Toll Free: 800-645-9116 24-Hour Technical Support: 800-34-VICON (800-348-4266) UK: 44/(0) 1489-566300 Vicon Industries Inc. does not warrant that the functions contained in this equipment will meet your requirements or that the operation will be entirely error free or perform precisely as described in the documentation. This system has not been designed to be used in life-critical situations and must not be used for this purpose.
www.vicon-security.com Document Number: 8009-8282-20-00 Product specifications subject to change without notice.
Issued: 1116 Copyright © 2016 Vicon Industries Inc. All rights reserved.
Quick Operation Guide
|
1
Surveyor MKII Camera Dome Quick Operation Guide
This manual provides a quick overview for the operation of the Surveyor® MKII Series of Camera Domes. Refer to the complete manual, XX282-0X (installation) and XX282-4X (web browser), for complete details on installation, setup and operating details. The Surveyor MKII is a compact network dome comprised of a camera/lens and pan/tilt drive in an attractive covert enclosure. Surveyor MKII is sold in a variety of prepackaged configurations. The Surveyor MKII supports high-profile H.264 or M-JPEG compression. The dome supports ONVIF open architecture connectivity to enable integration into third party software recording solutions, as well as Vicon’s Valerus and ViconNet VMS. The Surveyor MKII is designed for easy installation and serviceability. The entire drive assembly simply snaps into the housing. When removed, the mechanism retains all programmed functions in its on-board memory. The customer interface board snaps down for easy access and the PCB provides removable terminal blocks for simple wiring connections. Power to the units can be provided by PoE+ (Power over Ethernet Plus. The Surveyor MKII includes a high-definition 2.0 megapixel day/night camera with wide dynamic range (WDR) and digital noise reduction (FNR).
2
|
Quick Operation Guide
Installation Outdoor and Impact-Resistant Pendant The Customer Interface (CI) board is packed separately with the mechanism. This has to be snapped into the housing.
Quick Operation Guide
Pressurized The Customer Interface (CI) board is packed separately with the mechanism. This has to be snapped into the housing.
|
3
4
|
Quick Operation Guide
Wiring and Setup CONNECTOR/PIN NUMBER
CONNECTOR TYPE
CONNECTOR/PIN LABEL
TERMINAL BLOCK
POWER (J2) AC+ ACALARM (J11) ALARM 1
J2-1 J2-2 TERMINAL BLOCK J11-1 J11-2 J11-3 J11-4 J11-5 J11-6 J11-7 J11-8
SIGNAL NAME
Hot Neutral Alarm I/O 1 Ground Alarm I/O 2 Ground Alarm I/O 3 Ground Alarm I/O 4 Ground
ALARM 2 ALARM 3 ALARM 4 TERMINAL BLOCK
J12-1 J12-2 J12-3 J12-4 RJ-45
COMM/RELAY (J12) VSS C NO NC LAN (J4)
Ground Relay, common Relay, normally open Relay, normally closed
J4-1 J4-2 J4-3 J4-4 J4-5 J4-6 J4-7 J4-8
Transmit + Transmit Receive + PoE spare PoE spare Receive PoE spare PoE spare 1/8-IN. PHONO
J8
AUDIO (J8) J8
Audio In
Communication Ports If using NTCIP protocol, communicate to the Surveyor MKII using ports 3000/UDP or 3001/TCP. If using ONVIF, use port 8000. This is set in the web browser.
Quick Operation Guide
Pressurized Cable Preparation Be sure to connect the plastic tube to the pressure sensor on the Customer Interface board. Using the prefabricated cable.
Using a customer prepared cable
|
5
6
|
Quick Operation Guide
Using the Web Browser Interface Web Browser Interface The Web Browser Interface provides a user friendly interface to configure and control various features and functions of the Surveyor MKII camera dome. The interface allows the configuration of camera dome parameters, viewing live video, using PTZ, setting administrative controls and collecting camera dome reports and status information.
Access the Camera Make sure the system has installed the player component. Active X controls are required; be sure the security settings for the IE browser are set to allow this. Open an Internet Explorer browser; although the dome can be used with 6.0 or later, Internet Explorer 11 is recommended for full functionality and required for the single file upgrade function. Enter the IP address or host name of the camera in the Location/Address field of your browser. The camera dome defaults to using DHCP. The Surveyor MKII login screen displays. Note that the Discovery tool utility for the Surveyor MKII is available on Vicon’s website, vicon-security.com, under Learn and Support, Software Downloads. The utility will not be included in the dome’s accessory kit.
Quick Operation Guide
|
7
Login The initial screen prompts the user to login with a user name and password. Upon first use, the default user name is ADMIN (upper case) and the password is 1234. It is recommended to modify the password of the admin user to ensure security of the system.
Click OK to enter the Surveyor MKII browser
After the login process, the Live view page displays. Along the left side of the screen there is a Navigation panel with tabs for selection of the other function areas in the Live view, Information, View, Function switch, PTZ control and PTZ function. •
Information provides date and time details.
•
View allows the stream settings, recording and snapshot options
•
Function provides, audio, motion detection and privacy mask features.
•
There are PTZ controls. The functions are Zoom In/Out, Focus Near/Far, Iris Open/Close and Pan and Tilt speed.
8
|
Quick Operation Guide
The Setting area allows for configuration of a variety of controls.
•
The System tab screen provides network, time zone settings and advanced settings for importing files, setting defaults and reboots.
•
The Network screen provides settings for FTP, SMTP, HTTPS, 802.1X, QoS, IGMP, SIP, MDA, DDNS, UPnP and IP filter.
•
The Camera screen allows programming Zoom/Iris/Focus, White balance, Exposure, Day/Night and some Special functions.
•
The Video and Audio screen provides settings for the three streams, Primary, Secondary and MJPEG, for resolution, frame rate, bit rate, etc.
•
From the PTZ screen presets, scans, auto tours, tours, privacy masks, home, RS-485 and motor controls are set up.
•
From the Schedules screen, a schedule of events for time of day and day of week can be set up.
•
The Alarm screen allows review and programming of alarms. There are 4 alarm inputs and 1 alarm output. An alarm schedule can be set up.
•
The Record screen provides the recording parameters for the primary and secondary streams and playback.
•
The Users screen allows the setup of additional users and changing of passwords. The system supports up to 8 users.
•
The Log screen provides up to 30 logs.
VICON INDUSTRIES INC. For office locations, visit the website: www.vicon-security.com
