Transcript
i SERIES Brochure 5/6/02 3:21 PM Page 1
COMPANY PROFILE
ORDERING INFORMATION
LSC Lighting Systems (Aust) Pty Ltd was
IPRO/A iPRO 12 channel x 13 Amp digital wall mount dimmer, with front panel mounted 12 x 15A 3 pin Australian output connectors.
established in January 2000 to continue the promotion and selling of lighting control products, traditionally designed and manufactured by LSC Electronics.
ATOM - entry level consoles in 12/24 and 24/48 models
maXim – advanced lighting consoles in 5 models from 12 to 120 faders, up to 1024 DMX channels with moving light control
IPRO/6A iPRO 6 channel x 25 Amp digital wall mount dimmer, with front panel mounted 6 x 25A 3 pin Australian output connectors.
LSC’s dedication to developing innovative products that are functional, stylish and cost effective to the end user is enhanced by the
ePAK & ePRO - rackmount 12 channel digital dimmers
IPRO/T iPRO 12 channel x 13 Amp digital wall mount dimmer, 12(MEN) x 4mm2 Screw Terminal output connectors, 5 x 10mm2 Screw Terminal power input connectors and DMX input internally wired.
reliability and serviceability of every product. The people at LSC consider all sales of its products, not as a purchase, but as a longterm investment by the end user.
iPAK & iPRO - professional range of installation dimmers
The product range is diverse and covers control desks, digital dimmers and a comprehensive selection of DMX512 distribution equipment. LSC has forged
monoPAK - single unit portable dimmer
a reputation for many years as a pioneer DMX Splitters Isolator/splitters in varying output models
in DMX512 technology and this will be further enhanced with the release of new products over the next twelve months. Products are distributed through a worldwide sales network of over 56 distributors in 31 countries and users of
Linklight - 48 channel converter
corporate/professional client to churches, schools, amateur theatre groups, convention and exhibition industries, broadcast industry, production and rental companies and basically anywhere good entertainment lighting is required.
IPRO/6T iPRO 6 channel x 25 Amp digital wall mount dimmer, 6(MEN) x 10mm2 Screw Terminal output connectors, 5 x 10mm2 Screw Terminal power input connectors and DMX input internally wired. IPRO/TE iPRO 12 channel x 13 Amp digital wall mount dimmer, 12(MEN) x 4mm2 Screw Terminal output connectors, 5 x 10mm2 Screw Terminal power input connectors and DMX input internally wired. EMC card fitted. IPRO/6TE iPRO 6 channel x 25 Amp digital wall mount dimmer, 6(MEN) x 10mm2 Screw Terminal output connectors, 5 x 10mm2 Screw Terminal power input connectors and DMX input internally wired. EMC card fitted.
DNA - range of isolated inlets, outlets and power supply’s for distributing DMX512
LSC equipment range from the high profile
IPAK/A iPRO 12 channel x 10 Amp digital wall mount dimmer, with front panel mounted 12 x 10A 3 pin Australian output connectors.
e24 - 24 channel dimming system with patch bay, monitoring and mains distribution
LSC’s commitment to leading the market in product innovation, styling and functionality
OPTIONS FOR DIMMERS ELINK Software upgrading option including PC style 3.5" disk and link cable.
IPCH/24 iPATCH 24 circuit Patch Panel with integral test socket and ammeter, 1.5m tails and moulded piggy - back plugs.
IPCH/30 iPATCH 30 circuit Patch Panel with integral test socket and ammeter, 1.5m tails and moulded piggy - back plugs.
IPCH/36 iPATCH 36 circuit Patch Panel with integral test socket and ammeter, 1.5m tails and moulded piggy-back plugs.
IPRO/SE iPRO 12 channel x 13 Amp digital wall mount dimmer, 12 x double Shuko output connectors and EMC card fitted.
IPCH/42
IPRO/UK iPRO 12 channel x 13 Amp digital wall mount dimmer, 24 x 15 Amp British output connectors and EMC card fitted.
IPCH/48
Note: iPRO dimmers can be supplied as SCR fired dimmers in lieu of standard Triac versions. To order, insert /SC after IPRO in the ordering code. Example: IPRO/SC/6T
IPCH/72
iPATCH 42 circuit Patch Panel with integral test socket and ammeter, 1.5m tails and moulded piggy - back plugs.
iPATCH 48 circuit Patch Panel with integral test socket and ammeter, 1.5m tails and moulded piggy-back plugs.
iPATCH 72 circuit Patch Panel in extended width chassis with integral test socket and ammeter, 1.5m tails and moulded piggy - back plugs.
continues with a program of new and upgraded products, that will see the company develop into one of the world’s
For Further Information Contact:
most respected and preferred suppliers of high quality Lighting Control Systems.
TDS - 48 channel dimming system with patch bay, digital monitoring and mains distribution
LSC Lighting Systems ( AUST ) Pty. Ltd. 7 University Place, Clayton, Victoria 3168 Australia
Telephone: +61 3 9561 5255 Facsimile: +61 3 9561 5277 Email:
[email protected] Web: www.lsclighting.com.au
Covering all Possibilities
i SERIES Brochure 5/6/02 3:21 PM Page 1
COMPANY PROFILE
ORDERING INFORMATION
LSC Lighting Systems (Aust) Pty Ltd was
IPRO/A iPRO 12 channel x 13 Amp digital wall mount dimmer, with front panel mounted 12 x 15A 3 pin Australian output connectors.
established in January 2000 to continue the promotion and selling of lighting control products, traditionally designed and manufactured by LSC Electronics.
ATOM - entry level consoles in 12/24 and 24/48 models
maXim – advanced lighting consoles in 5 models from 12 to 120 faders, up to 1024 DMX channels with moving light control
IPRO/6A iPRO 6 channel x 25 Amp digital wall mount dimmer, with front panel mounted 6 x 25A 3 pin Australian output connectors.
LSC’s dedication to developing innovative products that are functional, stylish and cost effective to the end user is enhanced by the
ePAK & ePRO - rackmount 12 channel digital dimmers
IPRO/T iPRO 12 channel x 13 Amp digital wall mount dimmer, 12(MEN) x 4mm2 Screw Terminal output connectors, 5 x 10mm2 Screw Terminal power input connectors and DMX input internally wired.
reliability and serviceability of every product. The people at LSC consider all sales of its products, not as a purchase, but as a longterm investment by the end user.
iPAK & iPRO - professional range of installation dimmers
The product range is diverse and covers control desks, digital dimmers and a comprehensive selection of DMX512 distribution equipment. LSC has forged
monoPAK - single unit portable dimmer
a reputation for many years as a pioneer DMX Splitters Isolator/splitters in varying output models
in DMX512 technology and this will be further enhanced with the release of new products over the next twelve months. Products are distributed through a worldwide sales network of over 56 distributors in 31 countries and users of
Linklight - 48 channel converter
corporate/professional client to churches, schools, amateur theatre groups, convention and exhibition industries, broadcast industry, production and rental companies and basically anywhere good entertainment lighting is required.
IPRO/6T iPRO 6 channel x 25 Amp digital wall mount dimmer, 6(MEN) x 10mm2 Screw Terminal output connectors, 5 x 10mm2 Screw Terminal power input connectors and DMX input internally wired. IPRO/TE iPRO 12 channel x 13 Amp digital wall mount dimmer, 12(MEN) x 4mm2 Screw Terminal output connectors, 5 x 10mm2 Screw Terminal power input connectors and DMX input internally wired. EMC card fitted. IPRO/6TE iPRO 6 channel x 25 Amp digital wall mount dimmer, 6(MEN) x 10mm2 Screw Terminal output connectors, 5 x 10mm2 Screw Terminal power input connectors and DMX input internally wired. EMC card fitted.
DNA - range of isolated inlets, outlets and power supply’s for distributing DMX512
LSC equipment range from the high profile
IPAK/A iPRO 12 channel x 10 Amp digital wall mount dimmer, with front panel mounted 12 x 10A 3 pin Australian output connectors.
e24 - 24 channel dimming system with patch bay, monitoring and mains distribution
LSC’s commitment to leading the market in product innovation, styling and functionality
OPTIONS FOR DIMMERS ELINK Software upgrading option including PC style 3.5" disk and link cable.
IPCH/24 iPATCH 24 circuit Patch Panel with integral test socket and ammeter, 1.5m tails and moulded piggy - back plugs.
IPCH/30 iPATCH 30 circuit Patch Panel with integral test socket and ammeter, 1.5m tails and moulded piggy - back plugs.
IPCH/36 iPATCH 36 circuit Patch Panel with integral test socket and ammeter, 1.5m tails and moulded piggy-back plugs.
IPRO/SE iPRO 12 channel x 13 Amp digital wall mount dimmer, 12 x double Shuko output connectors and EMC card fitted.
IPCH/42
IPRO/UK iPRO 12 channel x 13 Amp digital wall mount dimmer, 24 x 15 Amp British output connectors and EMC card fitted.
IPCH/48
Note: iPRO dimmers can be supplied as SCR fired dimmers in lieu of standard Triac versions. To order, insert /SC after IPRO in the ordering code. Example: IPRO/SC/6T
IPCH/72
iPATCH 42 circuit Patch Panel with integral test socket and ammeter, 1.5m tails and moulded piggy - back plugs.
iPATCH 48 circuit Patch Panel with integral test socket and ammeter, 1.5m tails and moulded piggy-back plugs.
iPATCH 72 circuit Patch Panel in extended width chassis with integral test socket and ammeter, 1.5m tails and moulded piggy - back plugs.
continues with a program of new and upgraded products, that will see the company develop into one of the world’s
For Further Information Contact:
most respected and preferred suppliers of high quality Lighting Control Systems.
TDS - 48 channel dimming system with patch bay, digital monitoring and mains distribution
LSC Lighting Systems ( AUST ) Pty. Ltd. 7 University Place, Clayton, Victoria 3168 Australia
Telephone: +61 3 9561 5255 Facsimile: +61 3 9561 5277 Email:
[email protected] Web: www.lsclighting.com.au
Covering all Possibilities
i SERIES Brochure 5/6/02 3:23 PM Page 2
PATCH PANEL The i PATCH series of lighting patch panels have been designed specifically with the installer in mind. Installation is a very quick, simple process for an electrician, as is adding further circuits at a future date.
DIGITAL DIMMERS
Whether it be a permanent installation, distributed dimming, exhibition or display, or small rental jobs; the i PAK and i PRO series of digital dimmers provide the most flexible solution to modern day dimming applications. Their unique design allows them to be bolted to walls, hung from trusses or hand rails, stored at the side of stage floors, or mounted into a 19 " equipment rack frame or cabinet.
The front cover is easily removable and contains the load test socket, ammeter and protecting Circuit Breaker for rapid testing of lamp loads on the patch circuits. The rear chassis has a neatly organised layout of terminals for the incoming load circuit wiring. There are four large knock - out panels on the rear chassis that can be utilised for the incoming load circuit wiring. For the user, circuits have been laid out in groups of 6, enabling quick location of a particular circuit number. In those dim lit situations, large bright numbers identify the circuit required, plus the moulded " Piggy - Back" plugs have white inserts to enable the correct orientation of the plug into a socket.
225 mm
1550 mm
There are three mounting styles available; direct mounting to a wall using the 5 recessed holes in the rear chassis, mounting to a 19" Equipment Rack frame, or hanging from a lighting bar or handrail using the holes in the top of the front cover to fit hanging clamps and a safety chain.
FLOOR LEVEL
SPECIFICATIONS • Multiple circuit sizes available – commencing from 24 circuits to 48 in increments of 6 circuits.
• Four 80mm x 60mm knock - out panels for cable entry located on rear chassis.
• Extended width housing available to accommodate 54, 60, 66 and 72 circuit versions.
- rear chassis finished in black stipple powdercoat
• GPO socket, ammeter and Circuit Breaker for testing load capacity of individual circuits.
&
• Construction: All zinc steel housings
- front cover finished in grey hammertone powdercoat with blue polycarbonate front decal. • Dimensions:
• Black moulded 463 "Piggy - Back" plugs on 1.5m black flexible cables.
IPCH/24 – IPCH/48 484mm (w) x 250mm (h) x 225mm (d)
• Very visible 10mm high circuit numbers affixed to cable next to "Piggy - Back" plugs.
IPCH/54 – IPCH/72 710mm (w) x 250mm (h) x 225mm (d)
The dimmers are of a two part hinged construction - the Dimmer Chassis and the rear Installation Frame. The Dimmer Chassis houses the control electronics, dimmer modules, output connectors, channel circuit breakers and input signal connectors. The Installation Frame houses the mounting locations for wall fixing and 19" rack mounting, the input power terminals and for the permanent installations models, all the output circuit terminals. This Frame is ideal to supply to contractors during construction to allow them to wire off the input power and output circuits. The Dimmer Chassis can be supplied once construction is finished and the site is free of debris, paint, concrete, and plaster dust. The hinged Dimmer Chassis also allows for ease of service, providing full access to electronics and electrical parts and wiring. A number of key criteria make the i PAK and i PRO stand out from the crowd. • The unique concept of using a central extruded aluminium heatsink as the base to mount inductors, Triacs, SCR’s and Circuit Breakers, all fan cooled allowing for very efficient operation at high load conditions.
• The use of high quality inductors and filtering circuits, minimising the possible interference to other electronic equipment by reducing the harmonic waves produced by phase angled control of the power mains.
TECHNICAL SPECIFICATIONS iPAK
iPRO
iPRO/6
Number of Dimmer Channels
12
12
6
Rating per Dimmer Channel
10 Amps
13 Amps
25 Amps
• Clever use of pushbuttons and displays to set the DMX512 address, to drive individual channels at varying levels, to create a 12 (6) channel scene that can be stored in non-volatile memory and to set a choice of fade curves for each dimmer channel.
Individual Channel Circuit Breakers
Yes
Yes
Yes
Circuit Breaker breaking capacity
6000 Amps
6000 Amps
6000 Amps
Current Control Technology©
Yes
Yes
Yes
Dimmer Curve selection per Channel
No
Yes
Yes
• The electronics will remember any stored scene or dimmer curve set-up that will be reactivated once power has been restored.
Scene Storage
Yes
Yes
Yes
Power Switching Circuitry
Soft - Fired
Hard - Fired
Hard - Fired
• Multiple output connector types, including Australian 10A, 15A and 25A 3 pin GPO’s, Shuko 16A and its variants and 15A UK style connectors.
Power-up in last known state
Yes
Yes
Yes
Channel Output Level mimic LEDs
Yes
Yes
Yes
Data OK and Error LEDs
Yes
Yes
Yes
• The i PRO has added features, such as 6 channel 25A variants, Triac or SCR operation or being able to set individual dimmer curve settings for each channel.
Inductor Rise Time (peak to peak)
200 - 250µs
200 - 250µs
200 - 250µs
Fan Cooling System Control
Two Speed
Variable
Variable
External software upgrading facility
Yes
Yes
Yes
Future software improvements can be loaded into the dimmers by the e LINK option; a Windows based program that allows the uploading of Software upgrades from a PC style computer. Downloads can be obtained from the LSC website or via email, then transferred into the dimmer using the e LINK cable connected between the PC and the DMX512 input connector on the dimmer.
DMX512 input and link-thru connectors
Yes
Yes
Yes
50/60 Hz Frequency Auto-Selection
Yes
Yes
Yes
100/120 Volt Power input (Factory set)
Yes
Yes
Yes
220/240 Volt Power input (Factory set)
Yes
Yes
Yes
Meets CE and C Tick requirements
Yes
Yes
Yes
DIMENSIONS:
484 (w) x 250 (h) x 220 (d) (iPAK/A, iPRO/A, iPRO/T, iPRO/6) 484 (w) x 330 (h) x 220 (d) (iPRO/SE) 484 (w) x 400 (h) x 220 (d) (IPRO/UK)
WEIGHT:
(unpacked) - 17kg (unpacked) - 19kg (unpacked) - 21kg
CONSTRUCTION:
Corrosion resistant steel finished in powder coating with rear-screened polycarbonate front panel. Front chassis is hinged to the rear mounting frame.
(packed) - 19kg (packed) - 25kg (packed) - 25kg
(iPAK/A, iPRO/A, iPRO/T, iPRO/6) (iPRO/SE) (iPRO/UK)
i SERIES Brochure 5/6/02 3:23 PM Page 2
PATCH PANEL The i PATCH series of lighting patch panels have been designed specifically with the installer in mind. Installation is a very quick, simple process for an electrician, as is adding further circuits at a future date.
DIGITAL DIMMERS
Whether it be a permanent installation, distributed dimming, exhibition or display, or small rental jobs; the i PAK and i PRO series of digital dimmers provide the most flexible solution to modern day dimming applications. Their unique design allows them to be bolted to walls, hung from trusses or hand rails, stored at the side of stage floors, or mounted into a 19 " equipment rack frame or cabinet.
The front cover is easily removable and contains the load test socket, ammeter and protecting Circuit Breaker for rapid testing of lamp loads on the patch circuits. The rear chassis has a neatly organised layout of terminals for the incoming load circuit wiring. There are four large knock - out panels on the rear chassis that can be utilised for the incoming load circuit wiring. For the user, circuits have been laid out in groups of 6, enabling quick location of a particular circuit number. In those dim lit situations, large bright numbers identify the circuit required, plus the moulded " Piggy - Back" plugs have white inserts to enable the correct orientation of the plug into a socket.
225 mm
1550 mm
There are three mounting styles available; direct mounting to a wall using the 5 recessed holes in the rear chassis, mounting to a 19" Equipment Rack frame, or hanging from a lighting bar or handrail using the holes in the top of the front cover to fit hanging clamps and a safety chain.
FLOOR LEVEL
SPECIFICATIONS • Multiple circuit sizes available – commencing from 24 circuits to 48 in increments of 6 circuits.
• Four 80mm x 60mm knock - out panels for cable entry located on rear chassis.
• Extended width housing available to accommodate 54, 60, 66 and 72 circuit versions.
- rear chassis finished in black stipple powdercoat
• GPO socket, ammeter and Circuit Breaker for testing load capacity of individual circuits.
&
• Construction: All zinc steel housings
- front cover finished in grey hammertone powdercoat with blue polycarbonate front decal. • Dimensions:
• Black moulded 463 "Piggy - Back" plugs on 1.5m black flexible cables.
IPCH/24 – IPCH/48 484mm (w) x 250mm (h) x 225mm (d)
• Very visible 10mm high circuit numbers affixed to cable next to "Piggy - Back" plugs.
IPCH/54 – IPCH/72 710mm (w) x 250mm (h) x 225mm (d)
The dimmers are of a two part hinged construction - the Dimmer Chassis and the rear Installation Frame. The Dimmer Chassis houses the control electronics, dimmer modules, output connectors, channel circuit breakers and input signal connectors. The Installation Frame houses the mounting locations for wall fixing and 19" rack mounting, the input power terminals and for the permanent installations models, all the output circuit terminals. This Frame is ideal to supply to contractors during construction to allow them to wire off the input power and output circuits. The Dimmer Chassis can be supplied once construction is finished and the site is free of debris, paint, concrete, and plaster dust. The hinged Dimmer Chassis also allows for ease of service, providing full access to electronics and electrical parts and wiring. A number of key criteria make the i PAK and i PRO stand out from the crowd. • The unique concept of using a central extruded aluminium heatsink as the base to mount inductors, Triacs, SCR’s and Circuit Breakers, all fan cooled allowing for very efficient operation at high load conditions.
• The use of high quality inductors and filtering circuits, minimising the possible interference to other electronic equipment by reducing the harmonic waves produced by phase angled control of the power mains.
TECHNICAL SPECIFICATIONS iPAK
iPRO
iPRO/6
Number of Dimmer Channels
12
12
6
Rating per Dimmer Channel
10 Amps
13 Amps
25 Amps
• Clever use of pushbuttons and displays to set the DMX512 address, to drive individual channels at varying levels, to create a 12 (6) channel scene that can be stored in non-volatile memory and to set a choice of fade curves for each dimmer channel.
Individual Channel Circuit Breakers
Yes
Yes
Yes
Circuit Breaker breaking capacity
6000 Amps
6000 Amps
6000 Amps
Current Control Technology©
Yes
Yes
Yes
Dimmer Curve selection per Channel
No
Yes
Yes
• The electronics will remember any stored scene or dimmer curve set-up that will be reactivated once power has been restored.
Scene Storage
Yes
Yes
Yes
Power Switching Circuitry
Soft - Fired
Hard - Fired
Hard - Fired
• Multiple output connector types, including Australian 10A, 15A and 25A 3 pin GPO’s, Shuko 16A and its variants and 15A UK style connectors.
Power-up in last known state
Yes
Yes
Yes
Channel Output Level mimic LEDs
Yes
Yes
Yes
Data OK and Error LEDs
Yes
Yes
Yes
• The i PRO has added features, such as 6 channel 25A variants, Triac or SCR operation or being able to set individual dimmer curve settings for each channel.
Inductor Rise Time (peak to peak)
200 - 250µs
200 - 250µs
200 - 250µs
Fan Cooling System Control
Two Speed
Variable
Variable
External software upgrading facility
Yes
Yes
Yes
Future software improvements can be loaded into the dimmers by the e LINK option; a Windows based program that allows the uploading of Software upgrades from a PC style computer. Downloads can be obtained from the LSC website or via email, then transferred into the dimmer using the e LINK cable connected between the PC and the DMX512 input connector on the dimmer.
DMX512 input and link-thru connectors
Yes
Yes
Yes
50/60 Hz Frequency Auto-Selection
Yes
Yes
Yes
100/120 Volt Power input (Factory set)
Yes
Yes
Yes
220/240 Volt Power input (Factory set)
Yes
Yes
Yes
Meets CE and C Tick requirements
Yes
Yes
Yes
DIMENSIONS:
484 (w) x 250 (h) x 220 (d) (iPAK/A, iPRO/A, iPRO/T, iPRO/6) 484 (w) x 330 (h) x 220 (d) (iPRO/SE) 484 (w) x 400 (h) x 220 (d) (IPRO/UK)
WEIGHT:
(unpacked) - 17kg (unpacked) - 19kg (unpacked) - 21kg
CONSTRUCTION:
Corrosion resistant steel finished in powder coating with rear-screened polycarbonate front panel. Front chassis is hinged to the rear mounting frame.
(packed) - 19kg (packed) - 25kg (packed) - 25kg
(iPAK/A, iPRO/A, iPRO/T, iPRO/6) (iPRO/SE) (iPRO/UK)
i SERIES Brochure 5/6/02 3:23 PM Page 2
PATCH PANEL The i PATCH series of lighting patch panels have been designed specifically with the installer in mind. Installation is a very quick, simple process for an electrician, as is adding further circuits at a future date.
DIGITAL DIMMERS
Whether it be a permanent installation, distributed dimming, exhibition or display, or small rental jobs; the i PAK and i PRO series of digital dimmers provide the most flexible solution to modern day dimming applications. Their unique design allows them to be bolted to walls, hung from trusses or hand rails, stored at the side of stage floors, or mounted into a 19 " equipment rack frame or cabinet.
The front cover is easily removable and contains the load test socket, ammeter and protecting Circuit Breaker for rapid testing of lamp loads on the patch circuits. The rear chassis has a neatly organised layout of terminals for the incoming load circuit wiring. There are four large knock - out panels on the rear chassis that can be utilised for the incoming load circuit wiring. For the user, circuits have been laid out in groups of 6, enabling quick location of a particular circuit number. In those dim lit situations, large bright numbers identify the circuit required, plus the moulded " Piggy - Back" plugs have white inserts to enable the correct orientation of the plug into a socket.
225 mm
1550 mm
There are three mounting styles available; direct mounting to a wall using the 5 recessed holes in the rear chassis, mounting to a 19" Equipment Rack frame, or hanging from a lighting bar or handrail using the holes in the top of the front cover to fit hanging clamps and a safety chain.
FLOOR LEVEL
SPECIFICATIONS • Multiple circuit sizes available – commencing from 24 circuits to 48 in increments of 6 circuits.
• Four 80mm x 60mm knock - out panels for cable entry located on rear chassis.
• Extended width housing available to accommodate 54, 60, 66 and 72 circuit versions.
- rear chassis finished in black stipple powdercoat
• GPO socket, ammeter and Circuit Breaker for testing load capacity of individual circuits.
&
• Construction: All zinc steel housings
- front cover finished in grey hammertone powdercoat with blue polycarbonate front decal. • Dimensions:
• Black moulded 463 "Piggy - Back" plugs on 1.5m black flexible cables.
IPCH/24 – IPCH/48 484mm (w) x 250mm (h) x 225mm (d)
• Very visible 10mm high circuit numbers affixed to cable next to "Piggy - Back" plugs.
IPCH/54 – IPCH/72 710mm (w) x 250mm (h) x 225mm (d)
The dimmers are of a two part hinged construction - the Dimmer Chassis and the rear Installation Frame. The Dimmer Chassis houses the control electronics, dimmer modules, output connectors, channel circuit breakers and input signal connectors. The Installation Frame houses the mounting locations for wall fixing and 19" rack mounting, the input power terminals and for the permanent installations models, all the output circuit terminals. This Frame is ideal to supply to contractors during construction to allow them to wire off the input power and output circuits. The Dimmer Chassis can be supplied once construction is finished and the site is free of debris, paint, concrete, and plaster dust. The hinged Dimmer Chassis also allows for ease of service, providing full access to electronics and electrical parts and wiring. A number of key criteria make the i PAK and i PRO stand out from the crowd. • The unique concept of using a central extruded aluminium heatsink as the base to mount inductors, Triacs, SCR’s and Circuit Breakers, all fan cooled allowing for very efficient operation at high load conditions.
• The use of high quality inductors and filtering circuits, minimising the possible interference to other electronic equipment by reducing the harmonic waves produced by phase angled control of the power mains.
TECHNICAL SPECIFICATIONS iPAK
iPRO
iPRO/6
Number of Dimmer Channels
12
12
6
Rating per Dimmer Channel
10 Amps
13 Amps
25 Amps
• Clever use of pushbuttons and displays to set the DMX512 address, to drive individual channels at varying levels, to create a 12 (6) channel scene that can be stored in non-volatile memory and to set a choice of fade curves for each dimmer channel.
Individual Channel Circuit Breakers
Yes
Yes
Yes
Circuit Breaker breaking capacity
6000 Amps
6000 Amps
6000 Amps
Current Control Technology©
Yes
Yes
Yes
Dimmer Curve selection per Channel
No
Yes
Yes
• The electronics will remember any stored scene or dimmer curve set-up that will be reactivated once power has been restored.
Scene Storage
Yes
Yes
Yes
Power Switching Circuitry
Soft - Fired
Hard - Fired
Hard - Fired
• Multiple output connector types, including Australian 10A, 15A and 25A 3 pin GPO’s, Shuko 16A and its variants and 15A UK style connectors.
Power-up in last known state
Yes
Yes
Yes
Channel Output Level mimic LEDs
Yes
Yes
Yes
Data OK and Error LEDs
Yes
Yes
Yes
• The i PRO has added features, such as 6 channel 25A variants, Triac or SCR operation or being able to set individual dimmer curve settings for each channel.
Inductor Rise Time (peak to peak)
200 - 250µs
200 - 250µs
200 - 250µs
Fan Cooling System Control
Two Speed
Variable
Variable
External software upgrading facility
Yes
Yes
Yes
Future software improvements can be loaded into the dimmers by the e LINK option; a Windows based program that allows the uploading of Software upgrades from a PC style computer. Downloads can be obtained from the LSC website or via email, then transferred into the dimmer using the e LINK cable connected between the PC and the DMX512 input connector on the dimmer.
DMX512 input and link-thru connectors
Yes
Yes
Yes
50/60 Hz Frequency Auto-Selection
Yes
Yes
Yes
100/120 Volt Power input (Factory set)
Yes
Yes
Yes
220/240 Volt Power input (Factory set)
Yes
Yes
Yes
Meets CE and C Tick requirements
Yes
Yes
Yes
DIMENSIONS:
484 (w) x 250 (h) x 220 (d) (iPAK/A, iPRO/A, iPRO/T, iPRO/6) 484 (w) x 330 (h) x 220 (d) (iPRO/SE) 484 (w) x 400 (h) x 220 (d) (IPRO/UK)
WEIGHT:
(unpacked) - 17kg (unpacked) - 19kg (unpacked) - 21kg
CONSTRUCTION:
Corrosion resistant steel finished in powder coating with rear-screened polycarbonate front panel. Front chassis is hinged to the rear mounting frame.
(packed) - 19kg (packed) - 25kg (packed) - 25kg
(iPAK/A, iPRO/A, iPRO/T, iPRO/6) (iPRO/SE) (iPRO/UK)
i SERIES Brochure 5/6/02 3:21 PM Page 1
COMPANY PROFILE
ORDERING INFORMATION
LSC Lighting Systems (Aust) Pty Ltd was
IPRO/A iPRO 12 channel x 13 Amp digital wall mount dimmer, with front panel mounted 12 x 15A 3 pin Australian output connectors.
established in January 2000 to continue the promotion and selling of lighting control products, traditionally designed and manufactured by LSC Electronics.
ATOM - entry level consoles in 12/24 and 24/48 models
maXim – advanced lighting consoles in 5 models from 12 to 120 faders, up to 1024 DMX channels with moving light control
IPRO/6A iPRO 6 channel x 25 Amp digital wall mount dimmer, with front panel mounted 6 x 25A 3 pin Australian output connectors.
LSC’s dedication to developing innovative products that are functional, stylish and cost effective to the end user is enhanced by the
ePAK & ePRO - rackmount 12 channel digital dimmers
IPRO/T iPRO 12 channel x 13 Amp digital wall mount dimmer, 12(MEN) x 4mm2 Screw Terminal output connectors, 5 x 10mm2 Screw Terminal power input connectors and DMX input internally wired.
reliability and serviceability of every product. The people at LSC consider all sales of its products, not as a purchase, but as a longterm investment by the end user.
iPAK & iPRO - professional range of installation dimmers
The product range is diverse and covers control desks, digital dimmers and a comprehensive selection of DMX512 distribution equipment. LSC has forged
monoPAK - single unit portable dimmer
a reputation for many years as a pioneer DMX Splitters Isolator/splitters in varying output models
in DMX512 technology and this will be further enhanced with the release of new products over the next twelve months. Products are distributed through a worldwide sales network of over 56 distributors in 31 countries and users of
Linklight - 48 channel converter
corporate/professional client to churches, schools, amateur theatre groups, convention and exhibition industries, broadcast industry, production and rental companies and basically anywhere good entertainment lighting is required.
IPRO/6T iPRO 6 channel x 25 Amp digital wall mount dimmer, 6(MEN) x 10mm2 Screw Terminal output connectors, 5 x 10mm2 Screw Terminal power input connectors and DMX input internally wired. IPRO/TE iPRO 12 channel x 13 Amp digital wall mount dimmer, 12(MEN) x 4mm2 Screw Terminal output connectors, 5 x 10mm2 Screw Terminal power input connectors and DMX input internally wired. EMC card fitted. IPRO/6TE iPRO 6 channel x 25 Amp digital wall mount dimmer, 6(MEN) x 10mm2 Screw Terminal output connectors, 5 x 10mm2 Screw Terminal power input connectors and DMX input internally wired. EMC card fitted.
DNA - range of isolated inlets, outlets and power supply’s for distributing DMX512
LSC equipment range from the high profile
IPAK/A iPRO 12 channel x 10 Amp digital wall mount dimmer, with front panel mounted 12 x 10A 3 pin Australian output connectors.
e24 - 24 channel dimming system with patch bay, monitoring and mains distribution
LSC’s commitment to leading the market in product innovation, styling and functionality
OPTIONS FOR DIMMERS ELINK Software upgrading option including PC style 3.5" disk and link cable.
IPCH/24 iPATCH 24 circuit Patch Panel with integral test socket and ammeter, 1.5m tails and moulded piggy - back plugs.
IPCH/30 iPATCH 30 circuit Patch Panel with integral test socket and ammeter, 1.5m tails and moulded piggy - back plugs.
IPCH/36 iPATCH 36 circuit Patch Panel with integral test socket and ammeter, 1.5m tails and moulded piggy-back plugs.
IPRO/SE iPRO 12 channel x 13 Amp digital wall mount dimmer, 12 x double Shuko output connectors and EMC card fitted.
IPCH/42
IPRO/UK iPRO 12 channel x 13 Amp digital wall mount dimmer, 24 x 15 Amp British output connectors and EMC card fitted.
IPCH/48
Note: iPRO dimmers can be supplied as SCR fired dimmers in lieu of standard Triac versions. To order, insert /SC after IPRO in the ordering code. Example: IPRO/SC/6T
IPCH/72
iPATCH 42 circuit Patch Panel with integral test socket and ammeter, 1.5m tails and moulded piggy - back plugs.
iPATCH 48 circuit Patch Panel with integral test socket and ammeter, 1.5m tails and moulded piggy-back plugs.
iPATCH 72 circuit Patch Panel in extended width chassis with integral test socket and ammeter, 1.5m tails and moulded piggy - back plugs.
continues with a program of new and upgraded products, that will see the company develop into one of the world’s
For Further Information Contact:
most respected and preferred suppliers of high quality Lighting Control Systems.
TDS - 48 channel dimming system with patch bay, digital monitoring and mains distribution
LSC Lighting Systems ( AUST ) Pty. Ltd. 7 University Place, Clayton, Victoria 3168 Australia
Telephone: +61 3 9561 5255 Facsimile: +61 3 9561 5277 Email:
[email protected] Web: www.lsclighting.com.au
Covering all Possibilities
