Transcript
CRT Monitor s7500mm Ensure that the following items are included with the monitor. If any items are missing, contact your HP authorized service provider.
1
s7500mm 17” monitor
4
Monitor power cable
2
Multimedia speaker stand
5
Documentation kit (Refer to the Reference Guide on the Software and Reference Library CD for detailed instructions on operating the monitor.)
3
Microphone/audio connectors cable
www.hp.com
1
CRT Monitor s7500mm
Attaching the Multimedia Speaker Stand a monitor base is attached to the monitor, remove it before attaching the multimedia speaker ✎ Ifstand. Refer to “Removing and Reattaching the Stand to a Replacement Monitor” in this document for instructions on removing the monitor base.
1. Align the hooks on the stand with the sockets on the bottom of the monitor and attach the stand.
2. Push the stand toward the front of the monitor until it stops.
repair service is required on the s7500mm monitor, do not return the multimedia speaker stand with the ✎ Ifmonitor. A replacement monitor will be sent to you and will not include the multimedia speaker stand. Before packing the defective monitor remove the multimedia speaker stand from the monitor. Return only the defective monitor to HP.
2
www.hp.com
CRT Monitor s7500mm
Removing and Reattaching the Stand to a Replacement Monitor Use the following procedure to: ■
Remove the monitor base from the replacement monitor.
■
Reattach the multimedia speaker stand to the replacement monitor.
1. To remove the monitor base, push the base toward the rear of the monitor until it stops.
2. Lift the base from the monitor and either return to it to HP along with the defective monitor or save the base for future use.
3. To reattach the multimedia speaker stand to the replacement monitor, refer to “Attaching the Multimedia Speaker Stand” on the previous page for instructions.
www.hp.com
3
CRT Monitor s7500mm
Connecting the Monitor and Stand identify the components on the multimedia speaker stand, refer to “Identifying the ✎ ToMultimedia Speaker Stand Components” in this document.
1. Turn off the computer and unplug the power cord. 2. Connect the monitor signal cable 1 to the computer’s video port (video board, video card, or graphics card). 3. Connect the microphone connector on one end of the microphone/audio connectors cable 2 to the microphone input jack on the computer’s sound card or microphone jack. Connect the other end of the microphone connector to the micicrophone input jack on the rear of the multimedia speaker stand. 4. Connect the audio connector on one end of the microphone/audio connectors cable 3 to the stereo output jack on the computer’s sound card or audio jack. Connect the other end of the audio connector to the audio input jack on the rear of the multimedia speaker stand. 5. Connect the attached power cable of the multimedia speaker stand 4 to the rear of the monitor. 6. Connect the monitor power cord 5 to the power connector on the rear of the multimedia speaker stand and the other end into a nearby wall outlet. 7. Reconnect the computer power cord 6 into the wall outlet. 8. Turn on the computer and monitor. The hardware installation is now complete. 9. On the multimedia speaker stand, turn the on/off volume control clockwise until it clicks to turn on the sound. 10. Using the computer, start a sound program to play music or sound effects while you slowly turn the on/off volume control clockwise to adjust to your desired volume level.
4
www.hp.com
CRT Monitor s7500mm
distortion may occur when the monitor is placed on top of a mostly hollow cabinet such as ✎ Sound the computer. If this occurs, place a pad underneath the multimedia speaker stand. High sound volume may also cause sound distortion; lower the volume.
Disconnecting Speaker Cables 1. Turn off the speakers, monitor and computer before removing or connecting cables. 2. Disconnect both the audio and microphone connectors on the microphone/audio connectors cable from the Multimedia Speaker Stand and from the computer’s sound card or jacks.
Identifying the Multimedia Speaker Stand Components Front Components
1
Power LED indicator light (green) glows when the speakers are turned on.
2
www.hp.com
On/Off volume control turns the sound on and off and adjusts sound level.
5
CRT Monitor s7500mm
Rear Components
6
1
Microphone input jack connects the microphone connector (pink) of the microphone/audio connectors cable.
4
Attached power cable plugs into the monitor’s power connector.
2
Audio input jack connects the audio connector (green) of the microphone/audio connectors cable.
5
Microphone connector
3
AC power connector connects the monitor power cable.
6
Headphones connector
www.hp.com
CRT Monitor s7500mm
www.hp.com
7
CRT Monitor s7500mm
© Copyright 2003 Hewlett-Packard Development Company, L.P. The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein.
8
www.hp.com
