Csor206

Transcript

CSOR206 (Option AA) CSOR206 CSOR206 (Option AB) 1Y-16 1Y-16 Distribution Matrix Applications Sports Bars Board Rooms • Matrix sizes from 4x4 up to 16x16 per signal type Home Theater Systems Distance Learning Broadcast Environments • Multiple I/O board combinations Security Systems Video Arraignment Systems • 400 MHz Ultra-Wideband performance CSOR206 GENERAL AC Power: 100 - 240 VAC Maximum Power Consumption: 30 Watts per enclosure Operational Temperature: 32º to 110º F (0º to 43º C) Humidity: 0 to 90% non-condensing Dimensions: 17.00 in (43.18 cm) depth 17.00 in (43.18 cm) width without mounting ears 19.00 in (48.26 cm) width with mounting ears 3.50 in (8.89 cm) height (2 r.u.) Weight: 17 lbs (7.73 kg) per enclosure Approvals: CE, ETL (conforms to UL 1419) AUDIO Throughput: Frequency Response: Total Harmonic Distortion + Noise: Crosstalk: Signal to Noise Ratio (SNR): Input: Maximum Level: < ± 0.1 dB (20 Hz to 20 kHz) < 0.01% (20 Hz to 20 kHz, Vin = -3.3 dBu to 13.2 dBu) < -95 dB (1 kHz, Vin = ± 24 V Balanced) -103 dB (20 Hz to 20 kHz, Vin = 13.2 dBu) Common Mode: 22.7 dBu Differential: 28.2 dBu 18 kΩ Balanced or Unbalanced Impedance: Type: Common Mode Rejection Ratio (CMRR): Power Supply Rejection Ratio (PSRR): Gain Adjustment Range (optional): Connector type(s): -3 dB to +10 dB (Vin = 3 Vp-p) Disconnectable, 3 Position Screw Terminal Output: Maximum Level: Impedance : Type: Gain Adjustment Range: Connector type(s): 25.96 dBu, Balanced 50 Ω Balanced or Unbalanced -3 dB to +10 dB Disconnectable, 3 Position Screw Terminal -90 dB typical, -70 dB min. (20 Hz to 20 kHz, Vcm = ± 10 V) -80 dB typical, -60 dB min. (20 Hz to 20 kHz, Vs = ± 15 V) Differential Gain: Differential Phase: Crosstalk (adjacent channel): Propagation Delay: Signal to Noise Ratio (SNR): Input: Maximum Level: Impedance: Gain Adjustment Range (optional): Connector type(s): Output: Maximum Level: Impedance: Gain Adjustment: Connector type(s): ± 3 dB to 60 MHz or Better ± 1 dB to 30 MHz or Better 0.1% or Better (f = 3.58 MHz) 0.1º or Better (f = 3.58 MHz) Crosstalk (adjacent channel): Propagation Delay: Output: Maximum Level: Impedance: Gain Adjustment: Connector type(s): Enclosures link for maximum flexibility Modular system with many I/O board types to precisely fit your application 4 slot (2 r.u.) ±5V 75 Ω or Hi-Z (22 kΩ) 6 slot (3 r.u.) -3 dB to +10 dB BNC 8 slot (4 r.u.) ±5V 75 Ω -7.5 dB to +7.5 dB BNC ULTRA-WIDEBAND VIDEO ± 3 dB to 200 MHz or better ± 3 dB to 400 MHz or better < -60 dB (f = 5 MHz) < -60 dB (f = 5 MHz) < 20 ns (Vin = ± 0.5 V) < 20 ns (Vin = ± 0.5 V) Signal to Noise Ratio (SNR): < -70 dB < -70 dB (Vin = 0.7 V, 100% IRE) (Vin = 0.7 V, 100% IRE) Input: Maximum Level: Impedance: Gain Adjustment Range (optional): Connector type(s): RS-232 serial control port CPU features 64 memory ”presets“ < -40 dB (f = 5 MHz) < 20 ns (Vin = ± 0.5 V) < -70 dB (Vin = 0.7 V, 100% IRE) WIDEBAND VIDEO Throughput: Frequency Response: • Matrix sizes from 4x4 up to 16x16 per signal type • Ideal for routing: Composite Video (NTSC, PAL, SECAM), Y/C and S-Video, Component Video, RGB, RGBS, RGBHV, Mono Audio, Stereo Audio, Serial Digital, RS-232, RS-422 • Multiple I/O board combinations • 400 MHz Ultra-Wideband performance • Switch any input to any or all outputs, or any combination • Multiple vertical enclosure size options for precise customization • Includes APControl, free Windows matrix control and scheduling software • X/Y Control Panels support quick disconnect and single touch status System Options: Local and Remote (to 1000 ft.) X/Y Control Panels Single Bus Controller Keypads Vertical Interval Switching Input Gain Control (Audio and Video) Redundant Power Supply 4-slot, 6-slot, and 8-slot enclosures CPU expansion slots for future options STANDARD VIDEO Throughput: Frequency Response: 1Y-16 Distribution Matrix Specifications 2 4 1 6 C he ne y - S p o ka ne R d. C he ne y, WA 9 9 0 0 4 - 0 3 5 0 509-235-2636 ±2V 75 Ω or Hi-Z (22 kΩ) ±2V 75 Ω or Hi-Z (22 kΩ) -3 dB to +10 dB BNC -3 dB to +10 dB BNC ±2V 75 Ω -5.5 dB to +6.7 dB BNC ±2V 75 Ω -5.5 dB to +6.7 dB BNC 800-622-0246 (US) w w w. a u t o p a t c h . c o m Fax 509-235-2646 e - ma i l : s a l e s @ a u t o p a t c h . c o m AutoPatch is a division of XN Technologies, Inc. CSOR206 (Option BA) VP201s/VP201b LCD Display CSOR206 (Option CA) 20.1" ThinEdge™ Ultra–Slim Bezel Display Immerse yourself in the panorama of this big-picture LCD. Turn your ideas into breathtaking reality with the 20" VP201s and VP201b LARGESCREEN THINEDGE ULTRA-SLIM BEZEL LCD displays. With astounding 176º ultrawide viewing angles, UXGA 1.92 megapixel resolution, ClearMotiv™ broadcast-quality video technology and native HDTV high-scan 720p compatibility, these displays boost professional productivity and heighten user enjoyment for video editors, financial traders, CAD/CAM engineers and power gamers. Ideal for multiple-panel configurations with height/pivot adjustments, digital/analog inputs and USB 2.0 high-speed connectivity, the VP201s and VP201b are the infinitely versatile professional desktop displays VP201b shown. Also available in silver (VP201s) of choice. Uncompromised features and versatility to have you seeing 20/20. > ThinEdge maximizes your productivity The ultra-slim 0.67" bezel design enhances your visual experience with clean, minimalist borders around the active image area. Suitable for tiling and stacking. > Ideal for multiple-monitor setups ThinEdge minimizes bezel gaps between panels for a virtually continuous viewing area in multiple-panel setups. > Pivot, height and wall-mount versatility VESA® wall-mount interface and detachable base for ergonomic flexibility with pivot, height, tilt and swivel adjustments. > analog/digital inputs and integrated USB hub expand your connectivity > Full ThinEdge design is ideal for multi-panel setups. Four unit panel-module-only (without base) multi-packs available. 20.1" viewable screen > 1600x1200 > High native resolution brightness and contrast 250-nit brightness (typ) and 400:1 contrast ratio (typ) for rich images. > HDTV–720p > Image ready clarity from all directions XtremeView® performance features ultra-wide 176º viewing angles horizontally and vertically. > Integrated power supply with hard power switch Includes one DVI-I (analog or digital capable) and one analog input. Integrated USB 2.0 high-speed hub enables unlimited connectivity and ENERGY STAR® TCO’03 for silver and TCO’99 for black models. options. > ClearMotiv > TCO’03 technology Ultra-fast 16ms video response enables digital HD broadcast-quality full-motion video at 62.5 fps. ThinEdge VP201s/VP201b LCD Display CSOR206 Pivot feature saves time Spend less time scrolling long documents. Simply rotate your screen from landscape to portrait. Wide-travel height adjustment With over 41/4 inches of travel, this LCD fits just right. LCD PANEL Type 20.1" color TFT active matrix UXGA LCD Display Area 16.1" (horizontal) x 12.1" (vertical); 20.1" diagonal Optimum Resolution 1600x1200 Contrast Ratio 400:1 (typ) Viewing Angles 176° horizontal, 176° vertical @ CR>10 Response Time 16ms (typ) Brightness 250 cd/m2 (typ) Glass Surface Anti-glare VIDEO INPUT Analog Digital Frequency Sync COMPATIBILITY PC Mac®* HDTV VGA up to 1600x1200 non-interlaced Power Mac™ G3/G4 up to 1600x1200 480p, 720p CONNECTOR Analog Digital USB Power 15-pin mini D-sub Digital DVI-I V 2.0 Up stream (B type) x1; Down stream (A type) x4 3-pin plug (CEE22) POWER Voltage Consumption AC 100–240V (universal), 50–60Hz 70W (typ) CONTROLS Basic OnView® Power, 1, down, up, 2 Auto image adjust, contrast, brightness, input select (D-sub, DVI-A, DVI-D), color adjust (9300K, 6500K, 5400K, 5000K, user color), information (H/V frequency, resolution, model number, serial number, web site), manual image adjust (H. size, H/V position, fine tune, sharpness, scaling), setup menu (language, resolution notice, input priority, OSD position, OSD timeout, OSD background, OSD pivot), memory recall OPERATING CONDITION Temperature Humidity 32–104° F (0–40° C) 10–90% (non-condensing) DIMENSIONS (W x H X D) Physical: 448mm x 480mm x 267mm (with stand) 17.6" x 18.9" x 10.5" (with stand) 448mm x 346mm x 71mm (without stand) 17.6" x 13.6" x 2.8" (without stand) WEIGHT Net Gross 18.7 lb. (8.5 kg) with stand; 11.5 lb. (5.2 kg) without stand 24.7 lb. (11.2 kg) with stand; 15.9 lb. (7.2 kg) without stand REGULATIONS UL, cUL, FCC-B, CB, CE, ENERGY STAR®, NOM, TUV/GS, TUV Ergo, (covers ISO13406-2 and MPR II) TCO’03 (VP201s), TCO’99 (VP201b), NEMKO, SEMKO, DEMKO, FIMKO, GOST-R, hygienic, SASO, PCBC, VCCI, BSMI, CCC, PSB, C-TICK, TUV-S POWER MANAGEMENT Meets TCO and ENERGY STAR® standards Hard power switch Integrated power supply RGB Analog (75 ohms, 0.7/1.0 Vp-p) DVI-D (TMDS, 100 ohms, or analog capable) Fh: 30~92kHz, Fv: 50~85Hz H/V separated, composite, sync-on-green (TTL) WARRANTY 1 up / 4 down USB 2.0 hub specifications 20.1" ThinEdge™ Ultra–Slim Bezel Display Three-year limited warranty on parts, labor and backlight. Analog VGA connector Digital/analog DVI-I connector ViewSonic Corporation’s QMS & EMS have been registered to ISO 9001 & ISO 14001, respectively, by the British Standards Institution. ViewSonic Corporation • 381 Brea Canyon Road, Walnut, CA 91789 Phone (800) 888-8583 or (909) 444-8888 • In Canada (866) 262-1967 • Fax (909) 839-7922 • [email protected] • ViewSonic.com *Adapter may be required. Analog adapter available from ViewSonic. Specifications subject to change without notice. Selection, offers and programs may vary by country; see your ViewSonic representative for complete details. Corporate names, trademarks stated herein are the property of their respective companies. Copyright © 2004 ViewSonic Corporation. All rights reserved. [12116-00B-08/04] VP201s-1/VP201b–1 For more product information, visit us on the web at ViewSonic.com CSOR206 (Option CA) CSOR206 (Option DA) CSOR206 (Option DA) Polycom® Vortex® EF2280 Acoustic echo/noise canceller with automatic microphone/matrix mixer Benefits Industry-leading acoustic echo and noise cancellation – Ensures the highest possible audio quality between sites High-quality audio – 20 kHz bandwidth, 270 ms tail length, more than 10 dB of room gain, and a convergence rate of over 40 dB per second on each mic/line channel Easy to operate – User-programmable delays on all outputs, up to 32 user-configurable presets, 16 factory presets, and 256 macros for flexible control Interoperable – Cascade up to eight Vortex EF2280 units for up to 64 mic channels, or link with Vortex EF2201, EF2210, EF2211 and other Polycom products Enjoy clear, understandable conversation in all conferencing applications. The Vortex EF2280 improves audio quality for conferencing, distance learning, and other installed applications through industry-leading acoustic echo and noise cancellation. The Vortex EF2280 automatically mixes your EF2280 features industry-leading acoustic echo microphones and other audio, while cancelling cancellation; a neural network Automatic Gain acoustic echoes and annoying background noise. Control (AGC) reacts only to valid speech pat- It is typically installed at each site in a multisite terns, bringing voices within desired levels. AGC network and includes inputs for microphones controls are user adjustable, as are settings for and line level, AEC reference, and auxiliaries, as the five-band parametric EQ offered on all input well as output destinations. The unit can be pro- and output channels and output delay controls. grammed from the front panel, or through Conference Composer software (included), The high-quality audio choice for The which programs the unit via RS-232. The 32 Polycom Office™ user-configurable presets are augmented by 16 With integrated video, voice, data, and Web capa- factory presets, which are geared for common bilities, The Polycom Office is the only solution applications such as boardrooms, courtrooms, that offers you an easy way to connect, confer- distance learning, and room combining. ence, and collaborate any way you want. The Polycom Office is our commitment to making A single Vortex EF2280 unit provides automatic distance communications as natural and interac- mixing of up to eight microphones plus four aux- tive as being there. Work faster, smarter, and bet- iliary audio sources. If more microphones are ter with the Polycom Vortex EF2280 and The needed, additional EF2280 or EF2241 units can Polycom Office. be linked, up to a total of eight. Number of Open Microphones (NOM) information can be specified across all channels in the linked units. The Connect. Any Way You Want. CSOR206 System Block Diagram and Rear Panel Output 1 Output 2 Line Line Output 3 Line Output 4 Line Output 5 Line Output 6 Line Output 7 Line Output 8 Line Output A Line Output B Line Output C Line Output D Line D/A D/A D/A D/A D/A D/A D/A D/A D/A D/A D/A D/A PEQ / DELAY PEQ / DELAY PEQ / DELAY PEQ / DELAY PEQ / DELAY PEQ / DELAY PEQ / DELAY PEQ / DELAY PEQ / DELAY PEQ / DELAY PEQ / DELAY PEQ / DELAY RS-232 Matrixing ASPI Bus Control/Status EN EN EN EN EN EN EN EN PEQ PEQ PEQ PEQ A/D A/D A/D A/D A/D A/D A/D A/D A/D A/D A/D A/D Level adjust Level adjust Level adjust Level adjust Level adjust Level adjust Level adjust Level adjust Phantom Phantom Phantom Phantom Phantom Phantom Phantom Phantom Mic/Line Mic/Line Mic/Line Mic/Line Mic/Line Mic/Line Mic/Line Mic/Line Level adjust Line Mic/Line 1 Mic/Line 2 Mic/Line 3 Mic/Line 4 Mic/Line 5 Mic/Line 6 Mic/Line 7 Mic/Line 8 Input A Level adjust Line Input B Level adjust EF Bus Level adjust Line Line Input C Input D EN (Echo Canceller, Noise Canceller) Ungated Echo Canceller Noise Canceller On Off AGC On Off EC1, EC2, Bus PEQ Parameters Mute On Off Gate Gated Parameters Polycom Vortex EF2280 Technical Specifications Dimensions Line Outputs • 19” (483 mm) W x 9.6” (244 mm) L x 1.75” (45 mm) H (one rack unit) Weight Connectors Output Impedance • 50 Ohms (drives 600 Ohms) RS-232: DB9F EF Bus In/Out: RJ45 Control /Status: DB25F Audio: Mini (3.5mm) quick connect terminal blocks Headroom • 20 dB, nominal Noise Cancellation • 0-15 dB, software selectable Operating Temperature • 0 °- 40 °C Control Inputs • Contact closure Status Outputs • 5 V, 20 mA each Signal to Noise Ratio Power • External supply (provided) • Input voltage of 110-240 VAC; 47-63 Hz; power consumption 30 W Microphone Input • Line level, 0 dB gain: >85dB Frequency Response • 20 Hz - 22 kHz Acoustic Echo Cancellation Span • -30 dBu to +0 dBu/ -66 dBu to -33 dBu, nominal; software selectable • 270 ms Total Cancellation Phantom Power • >65 dB • 24 V, software selectable Convergence Rate Line Inputs • -20 dBu to +0 dBu, nominal; software adjustable www.polycom.com Input Impedance • >10 k Ohms • 4 lbs. (1.8 kg) dry, 5.5 lbs. (2.5 kg) shipping • • • • • -20 dBu to +0 dBu, nominal; software adjustable • 40 dB/second ©2003 Polycom, Inc. All rights reserved. Polycom, the Polycom logo, and Vortex are registered trademarks and The Polycom Office is a trademark of Polycom, Inc. in the U.S. and various countries. All other trademarks are the property of their respective companies. Specifications subject to change without notice. For Architect's and Engineer's Specifications, please visit Polycom.com, or contact the Installed Voice Business Group at 1.770.641.4400. Polycom, Inc.: 4750 Willow Road, Pleasanton, CA 94588 (T) 1.800.POLYCOM (765.9266) for North America only. For North America, Latin America and Caribbean (T) +1.925.924.6000, (F) +1.925.924.6100 Polycom EMEA: 270 Bath Road, Slough, Berkshire SL1 4DX, (T) +44 (0)1753 723000, (F) +44 (0)1753 723010 Polycom Hong Kong Ltd.: Polycom Hong Kong Ltd., Rm 1101 MassMutual Tower, 38 Gloucester Road, Wanchai, Hong Kong, (T) +852.2861.3113, (F)+852.2866.8028 Part No. 3726-82280-001 Rev. 03/03 (Option DA) This symbol is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. IMPORTANT! FOR YOUR PROTECTION, PLEASE READ THE FOLLOWING: WATER AND MOISTURE: Appliance should not be used near water (near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, or near a swimming pool, etc). Care should be taken so that objects do not fall and liquids are not spilled into the enclosure through openings. POWER SOURCES: The product should be connected to a power supply only of the type described in the operating instructions or as marked on the appliance. GROUNDING OR POLARIZATION: Precautions should be taken so that the grounding or polarization is not defeated. POWER CORD PROTECTION: Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the appliance. SERVICING: The user should not attempt to service the appliance beyond that described in the operating instructions. All other servicing should be referred to qualified service personnel. FUSING: If your unit is equipped with a fuse receptacle, replace only with the same type fuse. Refer to replacement text on the unit for correct fuse type. SAFETY INSTRUCTIONS (EUROPEAN) The conductors in the AC power cord are colored in accordance with the following code. GREEN & YELLOW—Earth BLUE—Neutral BROWN—Live U.K. MAIN PLUG WARNING: A molded main plug that has been cut off from the cord is unsafe. NEVER UNDER ANY CIRCUMSTANCES SHOULD YOU INSERT A DAMAGED OR CUT MAIN PLUG INTO A POWER SOCKET. Your Carvin product is guaranteed against failure for ONE YEAR. Carvin will service and supply all parts at no charge to the customer providing the unit is under warranty. Shipping costs are the responsibility of the customer. CARVIN DOES NOT PAY FOR PARTS OR SERVICING OTHER THAN OUR OWN. A COPY OF THE ORIGINAL INVOICE IS REQUIRED TO VERIFY YOUR WARRANTY. Carvin assumes no responsibility for horn drivers or speakers damaged by this unit. This warranty does not cover, and no liability is assumed, for damage due to: natural disasters, accidents, abuse, loss of parts, lack of reasonable care, incorrect use, or failure to follow instructions. This warranty is in lieu of all other warranties, expressed or implied. No representative or person is authorized to represent or assume for Carvin any liability in connection with the sale or servicing of Carvin products. CARVIN SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. When RETURNING merchandise to the factory, you may call for a return authorization number. Describe in writing each problem. If your unit is out of warranty, you will be charged the current FLAT RATE for parts and labor to bring your unit up to factory specifications. HELP SECTION 1) WILL NOT TURN ON Check the power to the unit. Check for tripped circuit breakers, unplugged extension cords or power-strip switches that may be turned off. Check the fuse. If a dark brownish color or no wire can be seen within the glass fuse, then replace. The unit may be perfectly fine but occasionally the fuse may blow because of high AC voltage surges. After the fuse has been replaced with the proper value and if the fuse fails again, the product will require servicing (be sure to use a slow blow fuse if required). Check your input and speaker output cables. 2) MAINTAINING YOUR EQUIPMENT Avoid spilling liquids or allowing any other foreign matter inside the unit. The panel of your unit can be wiped from time to time with a dry or slightly damp cloth in order to remove dust and bring back the new look. As with all pro gear, avoid prolonged use in caustic environments (salt air). When used in such an environment, be sure the amplifier is adequately protected by rack, covers, etc.. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL! THIS UNIT CONRISK OF ELECTRIC SHOCK TAINS HIGH VOLTAGE INSIDE! CAUTION REPLACEMENT PARTS LIST FOR DCM AMPS DCM150 21-50311 REV A 2 EACH JACK PHONO MONO PCB MOUNT 58-10035 1 EACH #QTY DESCRIPTION 03-00450 1 EACH INSLTR 9.125x1.5x.01" SGL ADHV 21-51545 2 EACH 2 EACH 58-10045 R122, R13, R222, R20, R21 R100, R101, R102, R103, 2 EACH BINDING POST RED/BLK EXT LEGS 03-10625 4 EACH STANDOFF NYLON #10X .625X .375 03-15010 2 EACH TOROID PAD 4.75" OD X 2" ID X0 03-18190 3 EACH CABLE TIE 4"LX .10"W 7/8 BNDLE 03-19810 4 EACH FOOT PVC BLK SQ"=.810 HGT=.300 03-49550 1 INCH TAPE W/ADHSVE 3M 80mil x 1.0" 05-48025 1 EACH SPADE CONNECT 18AWG BLK 254MM 05-48522 2 EACH SPADE CONNECT 18AWG GRN 228MM 05-68415 1 EACH CABLE RIBBON 24A 8P/ 6" W/HDR 05-60420 1 EACH CABLE RIBBON 24A 10P/ 8" W/HDR 05-64435 1 EACH CABLE RIBBON 24A 4P/14" W/HDR 06-09252 2 EACH NUT FOR POT 71-09252C 06-10045 6 EACH SMS PFH #6X .375 TYPE AB BLACK 06-10061 2 EACH SMS PPH #6 X .375 TYPE A BLACK 06-10070 4 EACH MS PPH 6-32X .500 BLACK 06-10080 4 EACH MS PPH 6-32X .750 BLACK 06-10100 4 EACH MS PPH 8-32X .375 BLACK 06-10193 1 EACH MS CTH #1/4-20X 1.250 BOLT BLK 06-40070 2 EACH TERMINAL .25"TAB/.156"LUG/.032 06-50035 8 EACH NUT KEP #6-32 06-50040 4 EACH NUT KEP #8-32 BLACK ZINC 06-50051 4 EACH NUT KEP #10-32 06-50061 1 EACH NUT HEX #1/4-20 ZINC W/NYLN IN 07-09012 2 EACH KNOB RECESSED MED 25.0mm BLACK C103, C104, C107, C11, C112, 10-01501E 1 EACH FRONT PANEL DCM150 C116, C12, C120, C203, C204, 10-82005 1 EACH LID DCM/HT POWER AMPS C207, C212, C216, C220, C7, C8 10-01509G 1 EACH CHASSIS DCM150 10-15045 1 EACH PLATE TOROID 4.5" DIA 14A GALV 12-01520A 1 EACH HEATSINK DCM150/PB200 15-01513 1 EACH XFORMR 120V HT150 25-31350 1 EACH SWITCH DPST ROCKER BLACK POWER 76-00001 1 EACH WARRANTY CARD "CARVIN" 76-00150 1 EACH MANUAL DCM150 77-01509B 1 EACH LABEL REAR DCM150 23-11008 2 EACH 2 EACH R200, R201, R202, R203 FUSEHOLDER CLIPS 3AG VERT MTG 58-10055 F1 23-11004 7 EACH 2 EACH R108, R208, R114, R214, R125, H1A, H1B R225, R138 CONNECT HEADER 8 PIN STRAIGHT 58-10065 2 EACH CONNECT HEADER 10 PIN STRAIGHT 3 EACH SWITCH DPDT PUSH PC MTG LOCKNG 58-15035 2 EACH 1 EACH SWITCH 4PDT PUSH PC MTG LOCKNG 58-15045 2 EACH 1 EACH 58-15055 4 EACH 49-10312 6 EACH 9 EACH PCB CARD MAIN HT150 PWR AMP 49-10451 2 EACH 49-22035 16 EACH CAP ELEC 2,200 MFD 35V 20% 49-25152 2 EACH 49-33212 2 EACH 49-33312 2 EACH 49-39052 6 EACH 58-22025 2 EACH 80-01528 58-22035 11 EACH R15, R218, R219, R226, R233, R239 58-22045 3 EACH 58-22055 2 EACH SMT CAP 22uF 35v ELECTROLITIC 58-27025 2 EACH 58-33025 1 EACH 6 EACH STANDOFF LED .925 x .215 T1 05-22102 4 INCH POLYOLEFIN SHRINK TUBING 1/16" 06-40050 1 EACH 6 EACH 7 EACH 58-33035 1 EACH 58-33045 2 EACH 0.033UF SMT 10% FILM 0805 50V 58-36055 1 EACH 4 EACH 58-00035 4 EACH TERMINAL 90dg MALE PC MTG .250 QC1, QC2, QC3, QC4, QC5, QC6 07-01603 4 EACH KNOB "6L" 6x6x17.4mm GREY CAP 21-31100 1 EACH RECEPTACLE AC W/FAST-ON CHASS 58-39035 1 EACH 58-47025 1 EACH PL1 5 EACH 2 EACH 82PF SMT 5% CERAMIC 0805 58-47035 2 EACH 60-55500 4 EACH TRANS 2N5550 HV NPN 250V T0-92 Q5, Q6, Q17, Q27 60-75200 4 EACH 58-47045 17 EACH 60-75320 3 EACH 60-75330 2 EACH 60-75340 1 EACH 60-78120-1 1 EACH EGULATOR VOLTAGE 12 (PREPPED) Q1 60-79120-1 1 EACH REGULATOR VOLTAGE 12 (PREPPED) Q2 62-00014 2 EACH MMBTA14 SOT-23 SMT Q102, Q202 62-19140 12 EACH 1N914 HI SPD SMT 250mW DIODE D201, D203, D204, D214, D7, 330.5 SMT .25W 1206 1% 3.3K SMT .25W 1206 1% D8, D9 62-45650 3 EACH 33K SMT .25W 1206 1% NJM4565 SMT DUAL HI FREQ A1, A2, A3 62-04739 1 EACH SMT DIODE ZENER 4739 Z1 62-54001 14 EACH MMBT5401LT1 PNP SOT-23 SMT R132, R232 Q10, Q11, Q12, Q13, Q16, Q20, 365K SMT .25W 1206 1% Q21, Q22, Q23, Q26, Q3, Q4 3.9K SMT .25W 1206 1% 470.5 SMT .25W 1206 1% 4.7K SMT .25W 1206 1% 47K SMT .25W 1206 1% R137, R17, R204, R205, R206, R220, R23, R235, R237, R238 R10, R123, R124, R223, R224 LED YELLOW DIFFUSED 3MM T-1.00 D5 270.5 SMT .25W 1206 1% 0.0 SMT JUMPER 1206 R136, R236 2 EACH LED GREEN DIFFUSED 3MM T-1.00 D102, D202 D10, D101, D103, D104, D11, R104, R105, R106, R120, R135, 58-47055 LED RED DIFFUSED 3MM T-1.00 D12, D100, D200 R111, R211 R130, R131, R230, R231 100.5 SMT .25W 1206 1% DIODE GEN RECT MR752 6A 200V D1, D2, D3, D4 Q100, Q200 62-55500 6 EACH 470K SMT .25W 1206 1% R140, R240 MMBT5550 NPN SOT-23 Q201, Q101, Q14, Q15, Q24, Q25 70-21050 1 EACH FUSE ABC 5.00A FAST 6.35X32MM F1 70-05713 2 EACH RELAY SPDT 12A@120VAC/24V COIL K1, K2 R5, R18 .47 OHM 5W 10% SB TRANSISTOR 15A 100V PNP Q19, Q29 R16 R129, R229, R26, R30 58-10025 60-00084 R25 0.047UF SMT 10% FILM 0805 50V RES 220K SMT .25W 1206 1% TRANSISTOR 15A 100V NPN Q18, Q28 R12 39PF SMT 5% CERAMIC 0805 C106, C206 55-04705 2 EACH R14 0.0033UF SMT 10% FILM 0805 50 C105, C115, C205, C215, C14, TERMINAL VERT MALE PC MTG .250 QC7 06-40060 49-82052 60-00083 R24 220PF SMT 5% CERAMIC 0805 C101, C102, C114, C214, C201 22K SMT .25W 1206 1% 910.5 SMT .25W 1206 1% R6, R7, R8, R9 R128, R228 C117, C217 03-92521 4 EACH R27, R134, R234 0.1 uF SMT 10% FILM 1206 50V C109, C209 2 EACH 2.2K SMT .25W 1206 1% 0.01UF SMT 10% FILM 080550V C108, C208 49-47312 220.5 SMT .25W 1206 1% C10, C110, C118, C119, C210, C113, C213 REV B 58-91025 R121, R221 C202 DCM150 PCB Sub Assemblies 150K SMT .25W 1206 1% R118, R119, R126, R133, R139, C111, C211 ZINC CADMIUM 15K SMT .25W 1206 1% C1, C2, C3, C4, C5, C6 C218, C219, C9, C13 ZINC CADMIUM 1.5K SMT .25W 1206 1% 680 SMT .25W 1206 1% R127, R227, R4, R1, R2, R3 R109, R209, R110, R210 PCB REV B 42-22235 6 EACH R28, R11 S1 30-01528 58-68025 R141, R241 S2, S3, S4 25-04201 1M SMT .25W 1206 1% 560.5 SMT .25W 1206 1% R107, R207 R19, R22 H2A, H2B 25-02201 2 EACH 100K SMT .25W 1206 1% CONNECT HEADER 4 PIN STRAIGHT H3A, H3B 23-11010 58-56025 10K SMT .25W 1206 1% XLR FEMALE CONNECTOR W/O GRND INSLTR MICA .0020".830"X .69" 03-10450 2 EACH 3 EACH J3, J4 03-00067-20 4 EACH 23-03529 R216, R29, R113, R213, R117, R217 JACK .250"PHONE STEREO PLASTIC J1, J2 21-40000 1K SMT .25W 1206 1% R112, R115, R116, R212, R215, J5, J6 PART CSOR206 LIMITED WARRANTY 71-09251 2 EACH POT 9 D-P 25F B10K THREAD BSH P1, P2 CARVIN ENGINEERING DATA The DCM150 professional amp is designed utilizing Carvin’s years of experience in power amp technology. It meets and exceeds every standard for professional amplification. The thick brushed anodized aluminum face plate, large recessed knobs and heavy-duty aluminum chassis reflect the manufacturing quality within. The DCM150 “High Energy Transfer” amp carrys the CE approval for world-wide use. PURE—TRANSPARENT SOUND Carvin considers the sound of an amp equally important as its reliability. To insure pure, uncolored sound, we designed one of the fastest responding power amps on the market today. High slew rates deliver superb transient response. High frequencies are transparent and open—even at high levels. Linear feedback circuits reduce distortion to near the theoretical zero limit preventing any type of harshness which would lead to ear fatigue. The DCM150 amp delivers flat, transparent, unaltered sound—especially important to the studio user. These amps are designed to deliver non-stop, continuous power and are completely protected from heat and short circuits. ULTRA RUGGED FOR TOURING Every chassis is made from heavy-duty 16 gauge aluminum that is lightweight and prevents rust. All internal cabling is neatly tied and harnessed. Heavy-duty power switches, recessed knobs & machined aluminum front panels all give the DCM amps a “tank-like” ability to handle rough, touring transport. TOTALLY MODULAR With the DCM150, Carvin brings you totally modular construction. If you ever need an I/O (input/output) connector card because a connector wore-out, just unplug it and re-install the replacement card in minutes. You don’t have to de-solder anything. This applies to every aspect of the DCM150 amp including the power supply, power cards, and heat sinks. Everything is connected by heavy-duty connectors for easy replacement—even the Toroid transformer is a total plug-in. LOSE THE WEIGHT...NOT THE PERFORMANCE For some companies, weight reduction means cost reduction. Carvin however, uses expensive TOROID transformers to reduce weight. Toroids deliver extra amounts of “on demand” current for continuous operation. This gives the power supply a solid foundation, yielding more headroom. Not only do toroids deliver high current, but they are known for reducing stray magnetic fields eliminating hum & noise. This is especially important for the recording industry. DCM150 POWER AMP CSOR206 OPERATING MANUAL FRONT PANELS & CONNECTING UP The DCM Series feature front panel signal, clip and protect LEDs which let you monitor the status of the amp. Both channels use precision level controls allowing you to see your settings at a glance. Balanced 1/4 phone & XLR input jacks are used to eliminate hum & noise. Speaker outputs feature 1/4” jacks. Heavy-duty binding posts that accept up to 50 amp #7 speaker wires. The rear professional accessory group offers a GROUND switch to remove the chassis ground from the XLR input, a PARALLEL input switch connects the inputs of both channels together eliminating Y connectors and allowing amp patching in multiple amp systems. The accessory group also features a BRIDGE mode switch for delivering full power into a mono 8Ω loud. RECEIVING INSPECTION—read before getting started INSPECT YOUR UNIT FOR ANY DAMAGE which may have occurred during shipping. If any damage is found, please notify the shipping company and CARVIN immediately. SAVE THE CARTON & ALL PACKING MATERIALS. In the event you have to re-ship your unit, always use the original carton and packing material. This will provide the best possible protection during shipment. CARVIN and the shipping company are not liable for any damage caused by improper packing. SAVE YOUR INVOICE. It will be required for warranty service if needed in the future. SHIPMENT SHORTAGE. If you find items missing, they may have been shipped separately. Please allow several days for the rest of your order to arrive before inquiring. RECORD THE SERIAL NUMBER on the enclosed warranty card or below on this manual for your records. Keep your portion of the card and return the portion with your name and comments to us. DCM150 POWER AMP SPECIFICATIONS: Output Power (BRIDGE MONO) 8Ω, 1kHz, < 1% THD 150 Watts Minimum Impedance (Bridged) 8 ohms (Stereo, both channels driven) 8Ω, 1kHz, < 0.5% THD 4Ω, 1kHz, < 0.5% THD Minimum Impedance THD 20-20kHz (8Ω typical) Frequency Response Input Impedance Damping Factor 60/60 Watts 75/75 Watts 4 ohms per channel < 0.1% < 0.05% ±0.5 dB, 20 Hz to 20 kHz > 20kΩ Balanced or Unbalanced >400 Sensitivity (@ 4Ω) 1.0 Vrms Output Noise -102 dBm Power Consumption 120V—200 VA For your records, you may wish to record the following information. Serial No._____________________ Invoice Date_______________ 76-00150 0801 Dimensions 1 3/4” High x 19” Wide x 10” Deep Weight (Net) 9lbs. 12340 World Trade Drive, San Diego, CA 92128 800 854-2235 www.carvin.com CSOR206 FRONT & REAR PANEL CONTROLS CLIP SIGNAL DCM150 13 15 17 19 12 22 30 50 PROFESSIONAL 150W AMPLIFIER 11 10 9 PROTECT 8 POWER 7 13 15 17 19 6 5 4 3 22 30 50 2 ∞ 1 0 dB EQ EXPAND 3 5 DCM150 SPEAKERS 1 4Ω MIN. BRIDGE 8 OHMS MIN. 2 8 7 6 5 4 3 CLIP SIGNAL 2 ∞ 1 0 dB 13 12 BRIDGE GND LIFT PAR INPUT 1 4Ω MIN. 2 4 6 STEREO AMPLIFIER 8 OHMS/CH 50 WATTS 4 OHMS/CH 75 WATTS 8Ω BRIDGED 150 WATTS 800-854-2235 www.carvin.com 11 10 9 CHANNEL TWO CHANNEL ONE 1 12 INPUT 2 MADE IN THE USA 120VAC~60Hz 125VA INTERNAL FUSE SERIAL NUMBER 14 9 10 11 7 8 FRONT PANEL 1. MOUNTING The rack mounting holes are designed on ISO standard spacing. Four 10-32 x .5” phillip machine screws are normally used to secure the amp. Rear support brackets are not required. 2. POWER SWITCH Check the power amp connections and verify the AC line power source before engaging the POWER switch. The yellow LED unmistakably indicates that all circuits are properly powered up. This color was chosen so the operator could see the red protect indicator from a distance. to signal –. The connector’s sleeve is then tied to ground through the GROUND LIFT switch–. 9. SPEAKER OUTPUTS The standard 1/4” SPEAKER jacks are used for most applications. Turn the amp off before connecting your speakers. 10. SPEAKER BINDING POSTS A precision input LEVEL attenuator is used to adjust the volume levels. To deliver the amps full power without reducing headroom of the signal source, the level controls should be turned up full. For heavy-duty speaker connections, use the rear BINDING POSTS to connect your speakers. Wire sizes up to 7 gauge (50 amps) can be inserted into the binding posts “side holes”. Larger cable can be used with “banana” plugs which plug into the ends of the binding post (remove colored caps). Binding posts are spaced on ISO standards. Use the two center RED binding posts for BRIDGE speaker connections (see 11 BRIDGE MODE). 4. CHANNEL SIGNAL INDICATOR 11. BRIDGE MODE—70V DISTRIBUTION SYSTEMS 3. CHANNEL LEVEL CONTROL The green SIGNAL LED indicators will start to flash when there is a signal passing to your speakers (-30dBM). This lets you know when the amp is passing a signal to your speakers. 5. CHANNEL CLIP INDICATOR The red CLIP LED indicators will start to flash when each channel has reached its maximum output. Occasional flashing caused by lower bass frequencies is OK. However, consistent flashing caused from higher frequencies may damage high frequency drivers (excessive distortion). This does not cause damage to the amp. 6. EQ EXPAND SWITCH When set to the ‘in’ position this circuit will cut the mids by -4dB at 1KHz. This works well as a loudness contour when operating at low volume levels or adds tone when using it in a bass or guitar rack. When set to the ‘out’ position it provides a flat, normal response. Try it both ways and set as desired. REAR PANEL 7. XLR CHANNEL INPUTS For most professional applications, use the XLR balanced input. This will help to reduce hum and allow of longer cable runs from your signal source (mixer, etc). Because this is a balanced input, the gain will be 6 dB higher than using a non balanced 1/4” input. XLR pin configuration: Pin 1: Grounded through the GROUND LIFT switch, Pin 2: positive Bal. signal and Pin 3: negative Bal. signal. 8. CHANNEL 1/4” PHONE JACK INPUT These 1/4” TRS phone jacks are designed to receive either balanced or unbalanced input signals. Balanced signals coming into this jacks should be wired with the connector’s tip going to signal + and the connector’s ring The DCM150 can be operated in bridge mode if you require a 70V distribution speaker system or a high powered mono (single channel) amp. With your amp off, push in the rear BRIDGE switch after you have made your speaker connections to the rear center RED binding posts (ch 1 is + and ch 2 is -). No other speaker jack or binding post can to be used at the same time!”. The INPUT and LEVEL is handled by channel 1. Channel 2 is non-operational. The minimum speaker impedance is 8 ohms. CAUTION: The power developed by bridging your amp can destroy speakers! 12. PARALLEL OR “Y” INPUTS The rear PARALLEL switch allows you to drive both channels from either input. All signals entering any input will be available on both channels. This eliminates Y adapter cables. This feature is used to “daisy chain” one piece of equipment to another. Just plug into the unused INPUT (1/4” or XLR) and it will become an output for other equipment. 13. INPUT GROUND LIFT Many times sound systems are connected in such a manner to cause a grounded loop with the inputs that result in audible hum. The input GND LIFT (1/4” & XLR) switch on the rear panel will help eliminate this problem. If not, another way to eliminate ground loops is to install a “line matching” transformer between the amplifier input and the signal source and cut the ground wire to PIN 1. 14. AC POWER Your amp is designed to run on either 120V 60 Hz. The voltage range for 120V is 95V to 132V. The rear heavy-duty AC cord is designed for your country. Be sure to check your power source before plugging into a grounded (3 prong) outlet. Never defeat the grounded connection or electrocution may result! CONNECTING THE SYSTEM CSOR206 SPEAKER CONNECTIONS The following diagrams illustrate typical connections. Although these illustrations show XLR’s for inputs and 1/4” plugs for outputs, a variety of alternative connectors are available. For most stage setups, mono (not stereo) is recomended. The reason for this is the audience on the left will not hear the same program material on the right if the program is done in true stereo. INPUT CONNECTIONS The preferred method of connecting input signals is with balanced XLR’s (two conductors plus a shield wire such as Carvin professional XLR cables). Balanced input signals provide the highest gain and best noise rejection. 1/4” stereo cables are also capable of providing balanced input by using a stereo plug (tip-positive, ring-negative & sleeve-ground). Not all sources provide balanced outputs. If this is the case, standard 1/4” input cables work fine with cable lengths under 25 feet (single conductor plus shield) providing there is no ground loop in the system. There are two 1/4” speaker jacks available for speaker connections (one for each channel). Additionally, there are two pairs of binding posts that not only allow for high current connections to speakers but are also used for “bridging” the amps output (see rear panel section 14 & 15). Use heavy gauge wire for all speaker connections (no lighter than 16 gauge up to 50’, Carvin’s PH50). Caution: Never use shielded cable (microphone or instrument input cable) to connect speakers. These cables will not handle the required current and may cause your amplifier to oscilate because of the internal shield. TYPICAL STEREO (BIAMP) SETUP Ch 1 Left (Hi Freq. Bi-Amp) Ch 2 Right TYPICAL MONURAL SETUP (Lo Freq. Bi-Amp) Use a XLR or 1/4" 2 or 3 cond. shielded cables To signal use XLR or 1/4" 2 or 3 cond. shielded cable DCM150 1 SPEAKERS 2 INPUT 1 STEREO AMPLIFIER 800-854-2235 www.carvin.com PARALLEL switch must be (IN) DCM150 SPEAKERS 1 2 INPUT 1 STEREO AMPLIFIER 8 OHMS/CH 50 WATTS 4 OHMS/CH 75 WATTS 8Ω BRIDGED 150 WATTS 800-854-2235 www.carvin.com BRIDGE 8 OHMS MIN. 4Ω MIN. PAR MADE IN THE USA 120VAC~60Hz 125VA INTERNAL FUSE 4Ω MIN. BRIDGE 8 OHMS MIN. INPUT 2 BRIDGE GND LIFT 4Ω MIN. USA 120VAC~60Hz 125VA INTERNAL FUSE SERIAL NUMBER PAR SERIAL NUMBER BRIDGE switch must be OFF (OUT). Full Range (Hi Freq. Bi-Amp) Horn System INPUT 2 BRIDGE GND LIFT 4Ω MIN. 8 OHMS/CH 50 WATTS 4 OHMS/CH 75 WATTS 8Ω BRIDGED 150 WATTS MADE IN THE BRIDGE switch must be OFF (OUT). Ch 1 Speaker Use 16 guage or heavier Non shielded cables (PH50). Plug into the 1/4" speaker jacks or strip and insert into speaker Binding Post (Red+ Black-) Ch 2 Speaker Use 16 guage or heavier Non shielded cables (PH50). Plug into the 1/4" speaker jacks or strip and insert into speaker Binding Post (Red+ Black-) Full Range (Lo Freq. Bi-Amp) Woofer System BALANCED MIC/LINE XLR CABLES -NEG. Activate the BRIDGE switch (IN). Control the level by Ch 1 ( Ch 2 does not function. Use a XLR or 1/4" 2 or 3 cond. shielded cables DCM150 1 SPEAKERS 2 INPUT 1 STEREO AMPLIFIER 8 OHMS/CH 50 WATTS 4 OHMS/CH 75 WATTS 8Ω BRIDGED 150 WATTS 800-854-2235 www.carvin.com 4Ω MIN. BRIDGE 8 OHMS MIN. 3 SHIELD TYPICAL BRIDGED SETUP 2 1 1 INPUT 2 BRIDGE GND LIFT 4Ω MIN. +POS. SHIELD PAR MADE IN THE USA 120VAC~60Hz 125VA INTERNAL FUSE SERIAL NUMBER 2 +POS. -NEG. 70V Distribution System: "TAP" Wattage of transformer (can vary from diagram) divided by total wattage of Amp = Number of transformer/speaker(s) that can be hooked up. 3 GND 1 + SIGNAL (BAL.) 2 3 - SIGNAL (BAL.) OR INTERRUPT (PATCH) STEREO OR BALANCED SIGNAL LINE Single speaker or system connected in BRIDGE mode. Minimum imp. 8 + SIGNAL (RETURN) - SIGNAL (SEND) SHIELD (GROUND) 15w 16 15w 16 7w 8 7w 8 3w 4 3w 4 1w + C (Shielded) SPEAKER OR SIGNAL LINE CABLE + TIP (HOT) 1w C (Unshielded) + C C SHIELD (GROUND) (Shielded) CSOR206 Option DD) U2020 100-Channel UHF Wireless System We can summarize the advantages of our U2020 wireless system in one word: More. Vega offers more brands of handheld microphone elements, like the Audix® OM6, Audio-Technica® ATM89R, Electro-Voice® N/D767 and many others, plus a large selection of lavalier mics. The U2020 has 380 available frequencies – that’s 165 more usable frequencies than our nearest competitor. High-selectivity receiver allows more systems at one location; up to twenty U2020’s work simultaneously without interference. A full 50 mW of transmitter output power results in a typical range of 1000 feet, more than double the range of most other systems. More applications for local broadcasters, theaters, Houses of Worship, live concerts, theme parks, schools and rental houses. www.clearcom.com CSOR206 U2020 100-Channel UHF Wireless System Specifications B SQUELCH AUDIO ATTEN MIC 12V DC AUDIO OUT A LINE/MIC/OUT LINE R-2020 RECEIVER CONTROL PANEL AND CONNECTORS 2.1 MM POWER JACK 12V DC B A MC-2020 MULTICOUPLER PANEL AND CONNECTORS B A B B A B A B A B A 4-UP SYSTEM WITH MULTICOUPLER A B A B A B A B A B A B A B A 6-UP SYSTEM WITH TWO MULTICOUPLERS The MC-2020 multicoupler powers all receivers through the antenna cables, eliminating extra power supplies in the rack (front or back antenna mounting allows even more installation flexibility). Ask for our Vega Applications Guide for more configurations and information. AUTHORIZED VEGA DEALER U2020 System Frequency Band: . . . . . . 708-782 MHz (4 bands A, B, C, D; C & D bands recommended for U.S.) Frequency Settings: . . . . . 100 channels (00-99) Audio Frequency Response: . 50-15,000 Hz, ± 1.5 dB Range: . . . . . . . . . . . 1,000 ft (300 m); 200-300 ft (60-90 m) in adverse conditions Audio Processing: . . . . . DX20 2:1 logarithmic companding Emission/Modulation: . . . . FM, 180KF3E Harmonic Distortion: . . . . < 0.25% (1 kHz) Ultimate S/N: . . . . . . . . > 100 dB (A-weighted) Squelch Quieting: . . . . . . 102 dB (A-weighted) Audio Output Line Level: . . . . . . -26 to +4 dBm Mic Level: . . . . . . -56 to -26 dBm IF Selectivity: . . . . . . . . 280 kHz RF Selectivity: . . . . . . . 22 MHz Adjustment and Control: . . Power, two 10-position frequency select switches, 30-dB level, 30-dB switchable pad, squelch control Indicators: . . . . . . . . . Audio level meter (5 position), RF level meter (5 position), Power, Diversity Power: . . . . . . . . . . . 5W maximum Weight: . . . . . . . . . . . 1 Lb, 14 oz (.85kg) Dimensions (hwd): . . . . . 1.65 x 7.15 x 9.25 inches (4.2 x 18.2 x 23.5 cm) Handheld Transmitter Microphone Elements: . . . Audix® OM6, A-T® ATM89R, EV® N/D767, N/D557, and N/D267. Other elements available; consult the Vega factory for availability. Power Output: . . . . . . . 50 mW Frequency Stability: . . . . . ± 0.005% Spurious Output: . . . . . . -53 dB maximum Controls: . . . . . . . . . . Power, Mute on/off, Mic level Audio Adjustment Range: . . 30 dB Antenna: . . . . . . . . . . Internal dipole Battery Life: . . . . . . . . > 6 hours Length (varies with element): . . Approx. 10.6 in (26.9 cm) Weight, with battery (varies): . Approx. 10 oz (283.5 g) Bodypack Transmitter Power Output: . . . . . Frequency Stability: . . . Spurious Output: . . . . Controls: . . . . . . . . Connector type: . . . . . Audio Adjustment Range: Antenna: . . . . . . . . Battery Life: . . . . . . Dimensions (hwd): . . . Manufactured by: Clear-Com Intercom Systems 4065 Hollis StreetEmeryville, California 94608 (510) 496-6666 • Fax (510) 496-6699 www.clearcom.com . . . . . . . . . . . . . . . . . . 50 mW ± 0.005% -53 dB maximum Power, Mute on/off, Mic level 4-pin Tini QG 30 dB 1/4-wave flexible whip > 6 hours 4 x 2.5 x 1.0 in (10.16 x 6.35 2.54 cm) Weight, with battery: . . . . 5.5 oz (155.7 g) CSOR206 (Option EA) *smith&nephew 640 Image Management System The Smith & Nephew 640 Image Management System offers the tools to facilitate documentation needs, including the easy acquisition, review and export of digital video clips, still images, and patient reports. In addition, the Windows® 2000 platform provides user screens that are easy to follow, compatibility with a variety of printers and DVD recorders, and a system that can easily be networked. CSOR206 Features Provides acquisition of still images and video clips in industry standard file formats (JPEG, bitmap, MPEG1 or MPEG2) Incorporates on-screen thumbnail review of still images and video clips, functionality for adding procedure notes, a choice of report formats, and the ability to connect an optional touch panel monitor Specifications Video Inputs Video Outputs Video Formats Network Port HERMES™ Port VGA Port Printer Port USB Port Power Requirements Motion Video Resolution Still Image Capture Resolution Dimensions Weight Hard Drive Processor Operating System Endoscopy Smith & Nephew, Inc. Andover, MA 01810 USA RGBS, S-Video, AUX Input, (Composite) RGBS, S-Video, AUX Input, (Composite) NTSC and PAL Ethernet 10-Base-T/100 Base-TX, auto-select RS-232 with USB type B, bidirectional port 16-pin female port Female DB-25 parallel port, bidirectional input/output USB Type A, software compatible with NS16C550 100–120/200–230 VAC, 50/60 Hz @ 150 VA MPEG1=352 x 240 (NTSC) 352 x 288 (PAL) MPEG2=704 x 480 (NTSC) 704 x 576 (PAL) BMP=640 x 480 (24-bit color) JPEG=640 x 480 DICOM=640 x 480 18 l x 17 h x 6.64 w (inches) 45.72 x 43.18 x 16.87 cm 21 lbs (9.5 kg) 20 GB 300 MHZ Intel Celeron Processor Windows 2000 www.smith-nephew.com T 978 749 1000 US Customer Service: 1 800 343 5717 International Customer Service: +1 978 749 1140 Generates an HTML report, allowing for easy, web-based surgical image management Supports a variety of Windows 2000 compatible printers and allows the user to choose their own printer (inkjet, laser, etc.) Offers compatibility with HERMES® Digital O.R. Control Center and seamless integration with Smith & Nephew’s DORAweb™ Information System Ordering Information Please contact customer service for product availability 7210235 640 Image Management System, English On-Screen Display and Operations Manual, U.S. Power Cord 7210237 640 Image Management System, Multi-language On-Screen Display and Operations Manual, Continental Power Cord 7210239 640 Image Management System, English On-Screen Display and Operations Manual, U.K. Power Cord Accessories 7210344 Touch Panel, LCD, 15 inch (domestic) 7210345 Touch Panel, LCD, 19 inch (domestic) 7207448 Iomega® 100 MB Zip… Disk 7207447 Iomega 250 MB Zip Disk 7209339 Single-pedal footswitch 7209340 Dual-pedal footswitch 7209338 650 MB or 700 MB CD-R Media 7210432 Single Arm, Vertical Mount 7210433 Double Arm, Vertical Mount 7210434 Double Arm, Desk Mount 7210435 Wall Mount Bracket ™ Trademark of Smith & Nephew. All other trademarks acknowledged ©2003 Smith & Nephew. All rights reserved. Printed in USA. 10/03 1061453 Rev. A CSOR206 (Option ED) The New Surgical Display Standard RadianceTM 19 · Ultra High Bright - High Contrast · Image Lag ReductionTM Technology · Super Fast Response · Picture PerfectTM Technology · Medical-Grade UL/IEC-60601-1 · Splash Proof · 24 VDC Remote Power The Radiance series of surgical displays are ideally suited for use with minimally invasive surgical equipment in the OR. These medical grade devices exceed the stringent performance and safety requirements necessary for use in a surgical environment, where superior image quality, true color reproduction, exceptional contrast, and high brightness are required. For mounting on light arms, the external 24Vdc power supply can be located up to 100 feet away from the display. Picture-Perfect TechnologyTM PPTTM technology, invented and used by NDS in manufacturing Radiance displays, eliminates the jagged edges that appear when interlaced video signals are displayed on a progressive scan flat-panel device (LCD or Plasma). NDS PPT uses proprietary angle correlated vector interpolation algorithms to eliminate intra-field spatial interpolation (staircasing effect), and enhances the visual quality necessary for tying sutures, examining tissues and other delicate procedures. Image Lag Reduction (ILR) for Super Fast Video Imaging Proprietary Image Lag Reduction technology (ILR), developed at NDS in conjunction with PPT, provides the fastest video imaging available in the market today. ILR technology anticipates the LCD drive required from one video frame to the next and modifies the LCD sub-pixel drive level to provide an industry-leading fast response time. These advanced interpolation and smoothing algorithms, result in images presented lag-free. Equipped with ILR technology, the Radiance display family delivers the fastest response time of any flat-panel display (between 10 and 16ms response time). Certifications/Compliance EN 60601-1, UL 60601-1 (Classified), MDD 93/42/EEC, IEC-601.1, EN 46001, CE, ISO 9001, ISO 13485, Class I Medical Device, FDA Registration #2954921 The Intelligent Solution CSOR206 The New Surgical Display Standard With 24Vdc power input, the Radiance is a perfect solution for boom arm mounting. Surgical and Radiology Support The Radiance display supports eight different video formats, including SDI, DVI digital, VGA analog, RGBS, Component Video, (YPbPr), S-Video(Y/C), Composite, and Sync-On-Green (SOG). And with gamma correction included, the Radiance is a perfect solution for fluoroscopy, ultrasound, PACS, MR, DR, etc. Remote Functionality Control for Switching Signals in Real-Time Integrated Operating Rooms require that display adjustments and video image source switching occur in real-time, without the intervention of the surgeon in the sterile field. Radiance displays answer this requirement with Remote Functionality Control (RFC) technology. All Radiance displays deliver RFC via a serial communication port located on the display. General Purpose Input Connector The General Purpose Input/Output (GPIO) connector allows customization to the Radiance display. It can be connected to a foot pedal to provide the surgeon with the ability to switch between different video sources, or be used to invoke the Tally-LampTM indicator. Medically Manufactured The Radiance is a professional medical device designed specifically for the OR environment. Unlike many LCD manufacturers who fashion existing off the shelf displays into medical equipment, this flat-panel is designed from the ground up for extreme durability and safety. Membrane style buttons and a non dimpled enclosure ensures particles or other foreign matter won’t accumulate into voids and possibly spread contaminants. The unit is designed to run without fans of any sort (internal or external) that could possibly make contaminants airborne and spread bacteria. Designed for safety, the low voltage input eliminates concerns with running mains power through a metal arm. In addition, the low voltage design allows the external power supply to be located up to 100 feet away from the display. The Intelligent Solution CSOR206 Radiance 19-inch specifications General Viewing Area (Diagonal) inches mm Active Area Inches mm Pixel pitch (mm) Native Resolution Luminance (cd/m2) Contrast ratio # of Colors Color Gamut (% SMPTE 296M, HD std.) Viewing Angle (degrees) Response Gamma: Display Technology Power Requirements Display DC Power Supply Power Consumption Dimensions inches mm Weight (lbs.) Inputs (for video input formats, see pg.4) Horiz Freq (kHz, max) Vertical Freq (Hz, max) Bandwidth (MHz, max) SDI S-video RGBS, YPbPr Composite Sync-On-Green (SOG) Graphics Inputs DVI VGA Control Inputs RS-232 GPIO Outputs SDI S-Video RGBS Composite User Controls OSD Operating Conditions Temperature Operating Storage Humidity Operating Storage Mounting NDS North America Corporate Headquarters 16245 Vineyard Blvd. Morgan Hill, CA 95037 TEL: 408.776.0085 FAX: 408.776.9878 email: [email protected] 19” 483 14.8 x 11.9 376 x 301 0.294 1280 x 1024 (SXGA) 450 650:1 16.77 million 100 ±85 10-16ms; gray — to — gray 1.8, 2.0, 2.2, 2.4, color corrected video gamma, & PACS a-Si TFT 16 – 24 VDC 100 to 240 VAC ± 10%, 50/60 Hz 40W 18 x 16 x 4 465 x 400 x 98 14 (6.4 Kg) 75 85 135 BNC, 75 Ω terminated BNC x 2 (Y & C), and DIN-4, 0.7 Vp-p ± 6db, 75 Ω terminated BNC x 4, or HD-15, 0.7 Vp-p ± 6db, 75 Ω terminated BNC, 0.7 Vp-p ± 6db, 75 Ω terminated BNC x 3, 75 Ω terminated DVI-d HD-15 DB-9 DIN-6 BNC DIN-4 BNC x 4, and HD-15 BNC R, G, B adjust, Hue, Saturation adjust, Color Temperature: D55/D65/D80/D93 Contrast, Brightness, Backlight Level , Horizontal & Vertical Position Overscan: Off / On (up to 25% overscan), Phase & Frequency 0 to +40 °C -20 to +60 °C 20 – 85 %RH 5 – 85 %RH 100 mm VESA NDS Europe Nijverheidscentrum 2D 2761 JP Zevenhuizen (ZH) The Netherlands Phone number : 0031 180 63 43 56 Fax number: 0031 180 63 21 91 www.nationaldisplay.com CSOR206 Video Input Formats Format Input Digital Analog Serial 576/50i (PAL) SDI 480/60i (NTSC) SDI 576/50p 480/60p 720/50p 720/60p 1080/50i 1080/60i Up to 1024/60p Comp, S-video, RGB, YPBPR Comp, S-video, RGB, YPBPR RGB, YPBPR, SOG RGB, YPBPR, SOG RGB, YPBPR RGB, YPBPR RGB, YPBPR RGB, YPBPR SOG Horiz. Freq (kHz) Interlace / Progressive Aspect Standard Digital/Analog 15.625 15.734 31.250 31.469 37.500 45.000 28.125 33.750 64.0, max Int Int Prog Prog Prog Prog Int Int Prog 16:9 / 4:3 16:9 / 4:3 16:9 / 4:3 16:9 / 4:3 16:9 16:9 16:9 16:9 - SMPTE SMPTE - 259M/C ITU 601 259M/C ITU 601 SMPTE 293M SMPTE 296M SMPTE 296M SMPTE 274M SMPTE 274M - All product names, trademarks or registered trademarks are the property of their respective holders. ** NDS continuously enhances its products, therefore specifications are subject to change without notice. NDS North America Corporate Headquarters 16245 Vineyard Blvd. Morgan Hill, CA 95037 TEL: 408.776.0085 FAX: 408.776.9878 email: [email protected] NDS Europe Nijverheidscentrum 2D 2761 JP Zevenhuizen (ZH) The Netherlands Phone number : 0031 180 63 43 56 Fax number: 0031 180 63 21 91 www.nationaldisplay.com Doc # Radiance 19” 60D0018A CSOR206 Communication Color Video Camera (Opton F) The Sony EVI-D100 (NTSC) and EVI-D100P (PAL) video cameras are a great choice for any application that requires a high-quality color video camera with the flexibility of remote pan/tilt/zoom operation, all in a compact easy-to-use package. These high quality CCD cameras combine a high-speed, quiet pan/ tilt with a wide angle of view and 40x zoom. Auto focus and automatic exposure control with back light compensation are fast and stable and can easily cope with difficult lighting conditions. The EVI-D100/P models are ideal for applications such as videoconferencing, distance learning and corporate training, surveillance, telemedicine, sports, concerts and internet communications such as webcasting. Additional advantages are provided by easy to use presets, daisy-chaining capability and various digital picture effects. EVI-D100 EVI-D100P Component/OEM FEATURES • High Speed, Wide Range Pan/Tilt The camera moves to a designated position quickly and immediately with one of the highest pan/tilt speeds in its class. Max. Pan speed: 300 degrees/s (range ± 100 degrees) Max. Tilt speed: 125 degrees/s (range ± 25 degrees) • Quiet Operation Direct drive motors account for the gearless structure of the camera, reducing the noise of pan/tilt motion drastically compared to conventional models. • 40x Zoom Ratio (10x Optical + 4x Digital) The fast and stable auto focus zoom lens reaches an impressive 40x zoom ratio. • Built-in Conversion Lens for Wide Angle View (65 degrees) The EVI-D100/D100P incorporates a newly developed wide-angle lens for wide field of view image capturing, making it ideal for use in small-sized rooms. • Six Position Presets with Battery Back-up An integral back-up battery stores presets of pan/tilt/zoom, focus position, AE mode and White balance mode, even when the unit is powered off. • Auto Sleep Function The camera can be set to automatically turn off when not in use after a specified period of time. • Various Picture Effects Mirror Image, Still Image on Field Memory, Pastel Image, Negative/Positive Reversal, Enhanced Contrast, etc. • Multi-function IR Remote Commander® unit Easy-to-use supplied remote commander unit is useful for basic pan/tilt/zoom camera control. • RS-232C Serial Control by VISCATM Control all camera settings and pan/tilt/zoom functions remotely via PC. this is not a rehearsal. w w w.sony-vision.com CSOR206 SPECIFICATIONS EVI-D100 Video Signal Image Sensor Effective Pixels Horizontal Resolution Lens Horizontal Angle of View Minimum Object Distance Minimum Illumination Auto Exposure Shutter Speed White Balance Effects EVI-D100P NTSC PAL 1/4 type Super HAD CCD 768 (H) x 494 (V) 752 (H) x 582 (V) 470 TV lines (Wide end) 460 TV lines (Wide end) x10 Optical Zoom, x40 with Digital Zoom, f = 3.1 to 31, F 1.8 to 2.9 6.6 to 65 degrees 100 mm (Wide end), 600 mm (Tele end) 3.5 lx (F1.8) Auto/Manual/Priority AE, Exposure compensation, Back light Compensation 1 ⁄ 4 to 1 ⁄ 10,000 s 1 ⁄ 3 to 1 ⁄ 10,000 s Auto, ATW, Manual, One Push, 3200K, 5800K Mirror Image, Still Image on Field Memory, Pastel Image, Negative/Positive Reversal, Sepia Image, Monochrome Image, Enhanced Contrast, Mosaic Image, Vertical Stretch, Horizontal Stretch, Motion Image on Still Image, Continuous Still Image, Motion Images on Binaried Still Image, After-image Lag of Moving Object More than 50 dB Horizontal ± 100 degrees (Max speed 300 degrees/s), Vertical ± 25 degrees (Max speed 125 degrees/s) (in 0.07 degrees increments) VBS, Y/C DC 10.8 to 13.0 V Max. 13.2 W (at 12 Vdc) 0 to 40 °C (32 to 40 °F) -20 to 60 °C (-4 to 140 °F) 113 (W) x 120 (H) x 132 (D) mm (4 1⁄2 x 4 3⁄4 x 5 1⁄4 inches) 860 g (1 lb 14 oz) AC Adaptor (x1), IR Remote Commander unit (x1), Velcro tape (x1), Operating Instructions (x1) S/N Ratio Pan/Tilt Video Output Power Requirements Power Consumption Operating Temperature Storage Temperature Dimensions Weight Supplied Accessories DIMENSIONS PAN/TILT RANGE Unit: mm 120 100 ° 24.5° * POWER RECIVE 113 132 0° 10 24.5° * 25° 19 °* Tripod Screw 25° °* 19 BACKUP ON OFF IR SELECT 1 2 3 VIDEO S VIDEO IN VISCA OUT DC IN 12.0V *Angle of view Product information is available on the Sony Home Page Click! http://www.sony-vision.com Sony Belgium (ICS) +32 2 724 18 24 Sony France (ICS) +33 1 55 90 41 58 Sony Germany (ICS) +49 221 537 8923 Sony Italy (ICS) +39 02 61 83 84 06 Sony Netherlands (ICS) +31 20 658 1502 Sony Nordic (ICS) +46 40 19 08 06 Sony Spain (ICS) +34 902 41 51 61 Sony UK (ICS) +44 1932 816 340 © 2001 Sony Corporation. All rights reserved. Reproduction in whole or in part without written permission is prohibited. Design and specifications are subject to change without notice. CA EVI-D100/100P/GB- / /2001 CSOR206 (Option F) CSOR206 CSOR206 CSOR206 (Option G) Displays up to four NTSC/PAL video inputs in scalable windows on a single screen Genlock capability Composite and S-video inputs Composite and S-video multi-image outputs Horizontal & vertical sizing, positioning, and blanking controls for each window MVP 104GX - MULTI VIDEO PROCESSOR Factory/user preset configurations Built-in stereo audio switcher RS-232/422 control CSOR206 APPLICATION SPECIFICATIONS Extron’s MVP 104GX is a multi video processor that allows a user to display up to four video signals simultaneously on a single screen for more powerful communications. Videoconferencing and distance learning applications benefit from the MVP 104GX’s independent input sizing and advanced decoding using a three-line adaptive comb filter. The MVP 104GX allows participants at the far end of a videoconference to view multiple images on one screen. This capability enables one or more participants at the near end to remain on-screen for face-to-face discussion while computer-video or other images are displayed. Video input and loop-through Number/signal type ............................. 4 S-video, 8 composite Connectors .......................................... 8 female BNCs, 4 4-pin mini-DIN Nominal level ...................................... 0.7V to 1V p-p Maximum level .................................... 2V p-p Input impedance ................................. 75 ohm Input frequency range ......................... NTSC/PAL Video output Connectors .......................................... 1 4-pin mini-DIN for S-video 2 female BNCs for composite Output standards ................................. Composite & S-video Nominal video level ............................. 0.7V to 1V p-p Impedance ........................................... 75 ohms Standards ............................................. NTSC 3.58, PAL Audio input Number/signal type ............................. 4 stereo, balanced/unbalanced Connectors .......................................... 4 3.5 mm captive screw terminals, 5 conductor Impedance ........................................... Unbalanced 50 k ohms, DC coupled, Balanced 25 k ohms, DC coupled Audio output Number/signal type ............................. 1 stereo, balanced/unbalanced Connectors .......................................... 1 3.5 mm captive screw terminals, 5 conductor Control/remote – video processor Serial control port ................................ 9-pin standard RS-232/RS-422 Baud rate ............................................. 9600 Protocol ............................................... 8-bit, 1 stop bit, no parity General Power .................................................. 100-240VAC, 50/60 Hz, 40 watts, internal Enclosure dimensions .......................... 3.5" H x 17.5" W x 10.1" D 8.8 cm H x 44.5 cm W x 25.6 cm D Shipping weight ................................... 15 lbs (6.8 kg) Part number ............................................. 60-320-02 Each video window can be independently scaled, positioned, or overlapped, so the user may display different window configurations such as picture in picture (PIP) or quad splitting. Horizontal and vertical sizing, positioning, and blanking controls are provided for each source. Images are routed from sources such as document cameras, CODEC cameras, VCRs, or DVD players. The windows can be labeled using up to 16 alphanumeric characters for on-screen identification, and a background color may be chosen to fill any unoccupied area. The “GX” version adds genlock capability for use in a system that requires synchronous timing. FEATURES ■ Inputs – Accepts up to four NTSC or PAL video inputs. Two inputs accept composite video or S-video, and two inputs accept composite video only. ■ Multi-image outputs – Three multi-image outputs provided simultaneously: two composite video outputs on BNCs and one S-video output on a 4-pin mini-DIN connector. ■ Picture controls – Provides horizontal & vertical sizing, positioning, and blanking controls for each window. ■ Freeze control – Includes freeze function to freeze individual windows of the multi-image output. Freezing all windows simultaneously is available through RS-232. ■ Factory/user preset memories – Convenient, one-touch selection of different windowing configurations during videoconferencing presentations available using 20 factory and 24 user memories for one, two, three, or four window display outputs. Presets include horizontal and vertical sizing, positioning, blanking, and priority settings for each window. ■ Blanking control – Extron’s exclusive variable horizontal and vertical blanking for each window. Using blanking, a user may add black lines at the edges of the window to eliminate edge noise. ■ Audio switching – Features 4 x 1 stereo audio switcher with 3.5 mm captive screw connectors for selecting the desired audio of any video input. APPLICATION DIAGRAM Extron VSC 150 PC Computer External Genlock Timing Scan Converter GEN RS-232 Control K LOCIN Y B/B32 G/Y RS-2 OUT Y R/R- HEIM ANA AV. Extron CERRITOS 5 LEWIS ST. Y DOUGLAS RD. AV. LINCOLN RGB B-Y/ R-Y/ Anaheim RD. WEST ST. BALL Disneyland HASTER ST. 75 OHM 57 BLVD. PAL OUT ST. MAC ANAHEIM 0.3A 0V H S-VID EAST ■ Input and preset labels – For easy recognition of input and preset buttons, the MVP 104GX allows the user to insert custom defined labels printed using Extron’s Windows®-based software, which provides text and/or graphics on customized labels. EO O U EO T P S-VID U T S STATE COLLEGE BLVD. S V O VIDE I N P U T S Stadium AV. KATELLA 100-24 VGA RS- T TPU OU R 1 L Hz 50/60 L T OU TPU L L INP INP INP UT IN INP UT 2 UT UT 4 1 2 UTS 3 INP L R 4 232 OTE REM R R R A C 3 IN B IN OUT Videoconferencing System OUT 1 OUT IN HEIM ANA 57 BLVD. LEWIS ST. CERRITOS DOUGLAS RD. AV. Extron 5 0.5A Anaheim WEST ST. Disneyland HASTER ST. RD. BALL 40V 100-2 Stadium AV. KATELLA AV. TOS CERRI Extron Anahei ST. AV. m AH STATE ST. Stadium EI M BLVD. COLLEGE RD. AN 57 Plasma Display EAST ANAHEIM BLVD. DOUGLAS 5 LINCO LN LEWIS ST. ST. RD. and Disneyl HASTER LA KATEL AV. BALL WEST Extron Electronics, USA 1230 South Lewis Street, Anaheim, CA 92805 800.633.9876 714.491.1500 FAX 714.491.1517 USA ST. ANAHEIM AV. LINCOLN Hz 50/60 MVP 104GX ■ RS-232 remote control – Extron’s Simple Instruction Set™ is provided for RS-232 control via Extron’s Windows®-based control program or third-party control. ■ Executive mode – Locks out front panel adjustments; all functions, however, remain active through RS-232. EAST ■ Genlock – Features the ability to genlock to an external black burst signal for use in timed or live environments that require genlock. STATE COLLEGE BLVD. OUT Document Camera Extron Electronics, Europe Beeldschermweg 6C, 3821 AH Amersfoort +31.33.453.4040 FAX +31.33.453.4050 The Netherlands VCR Video Camera Extron Electronics, Asia 135 Joo Seng Rd. #04-01, PM Industrial Bldg. +65.383.4400 FAX +65.383.4664 Singapore 368363 VCR Extron Electronics Information ExtronWEB™: www.extron.com ExtronFAX™: 714.491.0192 24-hour access—worldwide! 00-08 68-504-01 REV. B