Culinaire™ 33" Dual Level Bowl ❏

Transcript

CULINAIRE™ 33" DUAL LEVEL BOWL 18 GAUGE STAINLESS STEEL CULINAIRE™ 33" STAINLESS STEEL KITCHEN SINK ❏ 7504.103 Top Mount • 18 Gauge Stainless Steel • 18/10 Chrome Nickel content • Dual level bowl design • Top mount • Single faucet hole • One accessory hole • Mounting clips supplied Nominal Dimensions: 838 x 559 x 229 x 129mm (33" x 22" x 9" x 5") ❏ 7504.000 Undercounter Mount 7504.103 Shown with 4137.100 Culinaire Pull-out Kitchen Faucet (not included) • 18 Gauge Stainless Steel • 18/10 Chrome Nickel content • Dual level bowl design • Undercounter installation • Mounting clips and cutout template supplied Nominal Dimensions: 785 x 536 x 220 x 120mm (31" x 21-1/8" x 8-5/8" x 4-3/4") Bowl sizes: Right Hand: 150mm (6") wide 343mm (13-1/2") front to back 121mm (4-3/4") deep Left Hand: 540mm (21") wide 476mm (18-3/4") front to back 219mm (8-5/8") deep Compliance Certifications Meets or Exceeds the Following Specifications: • ASME A112.19.3 for Stainless Steel Plumbing Fixtures • CSA B45 for Plumbing Fixtures 7504.000 Shown with 4233.701 Culinaire Kitchen Faucet (not included) SEE REVERSE SIDE FOR ROUGHING-IN DIMENSIONS To Be Specified: ❏ Color: Stainless Steel ❏ Faucet*: ❏ Faucet Finish: ❏ Basket Strainer: 4331.013 ❏ Soap Dispenser: 4503.115 ❏ Vinyl Coated Bottom Sink Rack-Lg: 7414.100 ❏ ❏ ❏ ❏ ❏ ❏ Vinyl Coated Dish Rack-Sm: 7532.100 Vinyl Coated Dish Rack-Lg: 7534.100 Wood Cutting Board-Rectangular: 9001.100 Stainless Steel Colander: 8130.100 Hole Cover Plug: 790773-0070A Top Mount Clip Kit for 1" plus-thick countertop: 790772-0070A * See faucet section for available models © 2008 AS America Inc. G5 Revised 2/08 CULINAIRE™ 33" DUAL LEVEL BOWL 18 GAUGE STAINLESS STEEL 7504.103 Top Mount 2-3/4" (70mm) 2-3/4" (70mm) 1-1/16" DIA. OPTIONAL FINISHED WALL OR SPLASHBACK 1-3/8" DIA. 8-3/4" (222mm) 2-7/8" (73mm) 6-3/8" (162mm) 11-1/4" (286mm) 22" (559mm) C/L 3-3/4" DIA. DRAIN (2 PLACES) CUTOUT AREA 32" X 21" (813 X 533mm) 3/16" (5mm) 3-3/4" (95mm) 16-1/2" (419mm) COUNTERTOP (BY OTHERS) NOTES: FITTINGS NOT INCLUDED AND MUST BE ORDERED SEPARATELY. PROVIDE SUITABLE REINFORCEMENT FOR ALL WALL AND COUNTERTOP SUPPORTS. IMPORTANT: Dimensions of fixtures are nominal and may vary within the range of tolerances established by ASME A112.19.3. These measurements are subject to change or cancellation. No responsibility is assumed for use of superseded or voided leaflet. 11-3/4" (298mm) 33" (838mm) SEALING COMPOUND 7/8" (22mm) 4-3/4" (121mm) 9" (229mm) 5-3/4" (146mm) 5-3/4" (146mm) 36" (914mm) SUGGESTED COUNTERTOP 1-1/2" O.D. TAILPIECE (2 PLACES) FINISHED FLOOR MTG. CLIP 1-9/16" (40mm) MAX. 13/16" (21mm) MIN. ADJ. SCREW 7504.000 Undercounter Mount MOUNTING CLIP DETAIL (TYP.) OPTIONAL 6" (152mm) NOTES: TEMPLATE PROVIDED WITH MOUNTING KIT FOR UNDER-COUNTER CUTOUT VARIATIONS. FINISHED WALL OR SPLASHBACK 10-1/2" (267mm) * 21-1/8" (537mm) FITTINGS NOT INCLUDED AND MUST BE ORDERED SEPARATELY. C/L 3-3/4" DIA. DRAIN (2 PLACES) PROVIDE SUITABLE REINFORCEMENT FOR ALL WALL AND COUNTERTOP SUPPORTS. IMPORTANT: Dimensions of fixtures are nominal and may vary within the range of tolerances established by ASME A112.19.3. These measurements are subject to change or cancellation. No responsibility is assumed for use of superseded or voided leaflet CUTOUT AREA 3-3/4" (95mm) 15-3/8" (391mm) 11-3/4" (298mm) 30-7/8" (784mm) COUNTERTOP (BY OTHERS) SEALING COMPOUND 4-3/4" MTG. CLIP (121mm) (SEE DETAIL) 8-5/8" (219mm) 5-3/4" (146mm) 5-3/4" (146mm) 36" (914mm) SUGGESTED 1-1/2" O.D. TAILPIECE (2 PLACES) FINISHED FLOOR COUNTERTOP BRASS INSERT 1/2" MIN. (13mm) SINK MTG. CLIP SCREW MOUNTING CLIP DETAIL (TYP.) © 2008 AS America Inc. G6 Revised 2/08