Transcript
QUICK START GUIDE
CY4521 EZ-PDTM CCG2 EVK STEP
Unpack the kit contents
1
USB Type-C to Type-A Adapter
USB 2.0 Type-A to Mini-B Cable
USB 3.0 Type-A to Type-B Cable CCG EVK Base Board
CY4521 CCG2 Daughter Card 24V DC Power Adapter
www.cypress.com/CY4521
STEP Verify that the user LED jumper (J11) is populated on the CCG EVK base board. Verify that the
2
VSYS selection jumper (J2) on the CCG2 daughter card is set to 3.3 V (position 1-2) and the IO Supply selection jumper (J3) is set to VDDD (position 2-3). Connect the DC power adapter (provided with the kit) to the DC power jack (J1) of the CCG base board. Plug the other end of the DC power adapter into an AC power socket. LED2 (Green) on the CCG2 daughter card and LED1 on the CCG EVK baseboard turn ON to indicate that the kit is powered. In addition, LED2 (Orange) on the CCG EVK baseboard blinks continuously to indicate that CCG firmware is executing.
J7 Consumer Power Output Header
J4 DisplayPort Connector J2 USB 3.0 Type-B Receptacle
J3 USB Type-C Receptacle
CYPD2122-24LQXIT
LED2 CY4521 CCG2 Daughter Card J2 VSYS Selection Jumper 1-2 Short: 3.3V supply coming from CCG base board (Default Setting) LED1 CY4521 CCG2 Daughter Card J3 IO Supply Selection Jumper 2-3 Short: Power from VDDD of CCG2 (Default Setting) J9 Debug Connector
LED1 CCG EVK Base Board LED2 CCG EVK Base Board J1 24V DC Power Supply (Provider) Connector J12 Variable Power Supply (Provider) Header
Reset Switch J11 LED Jumper
J5 USB 2.0 Mini-B Receptacle
QUICK START GUIDE
CY4521 EZ-PDTM CCG2 EVK STEP Connect the USB 3.0 Type-A to Type-B cable from the PC to the USB Type-B receptacle (J2) of the
3
CCG base board. Connect the USB Type-C to Type-A adapter to the USB Type-C receptacle (J3) of the CCG base board. Plug a USB flash drive (not provided with the kit) into the USB Type-C to Type-A adapter. Verify your setup as shown in the picture below. Observe the enumeration of the USB flash drive on the PC. Initiate data transfer between the PC and the flash drive, and observe the data transfer speed*.
USB 3.0 Type-A to Type-B cable
J2
USB flash drive USB Type-C to Type-A adapter 24 V DC from output of power adapter
Note that any USB device can be used instead of a flash drive with the setup shown in step 3. * Data transfer speed depends on the type of the USB port (SuperSpeed or High Speed) of the PC, read/write speed of the flash drive (SuperSpeed or High Speed) and the system configuration. You can evaluate the reversibility of the Type-C interface by detaching the USB Type-C to Type-A adapter, reconnecting it in an upside-down orientation and observing its enumeration.
STEP For more details, refer to the CY4521 Kit Guide.pdf** located at
4
C:\Program Files (x86)\Cypress\CY4521 EZ-PD CCG2 EVK\1.0\Documentation on 64-bit Windows operating systems or C:\Program Files\Cypress\CY4521 EZ-PD CCG2 EVK\1.0\Documentation on 32-bit Windows operating systems. ** Download and install the CY4521 EZ-PD CCG2 EVK setup file from www.cypress.com/CY4521 to access the latest kit design files and documentation
© 2016 - 2017 Cypress Semiconductor Corporation. All rights reserved. All trademarks or registered trademarks referenced herein are the properties of their respective owners. 002-15677 Rev.*B
