Transcript
CFSW-51MHL
5 by 1 HDMI with MHL Switcher
Operation Manual
DISCLAIMERS The information in this manual has been carefully checked and is believed to be accurate. Cypress Technology assumes no responsibility for any infringements of patents or other rights of third parties which may result from its use. Cypress Technology assumes no responsibility for any inaccuracies that may be contained in this document. Cypress also makes no commitment to update or to keep current the information contained in this document. Cypress Technology reserves the right to make improvements to this document and/or product at any time and without notice.
COPYRIGHT NOTICE No part of this document may be reproduced, transmitted, transcribed, stored in a retrieval system, or any of its part translated into any language or computer file, in any form or by any means— electronic, mechanical, magnetic, optical, chemical, manual, or otherwise—without express written permission and consent from Cypress Technology. © Copyright 2011 by Cypress Technology. All Rights Reserved. Version 1.0 December 2011
TRADEMARK ACKNOWLEDGMENTS All products or service names mentioned in this document may be trademarks of the companies with which they are associated.
SAFETY PRECAUTIONS Please read all instructions before attempting to unpack, install or operate this equipment and before connecting the power supply. Please keep the following in mind as you unpack and install this equipment: •
Always follow basic safety precautions to reduce the risk of fire, electrical shock and injury to persons.
•
To prevent fire or shock hazard, do not expose the unit to rain, moisture or install this product near water.
•
Never spill liquid of any kind on or into this product.
•
Never push an object of any kind into this product through any openings or empty slots in the unit, as you may damage parts inside the unit.
•
Do not attach the power supply cabling to building surfaces.
•
Use only the supplied power supply unit (PSU). Do not use the PSU if it is damaged.
•
Do not allow anything to rest on the power cabling or allow any weight to be placed upon it or any person walk on it.
•
To protect the unit from overheating, do not block any vents or openings in the unit housing that provide ventilation and allow for sufficient space for air to circulate around the unit.
REVISION HISTORY VERSION NO.
DATE
SUMMARY OF CHANGE
RDV1
12/06/2011
PreliMINary Release
CONTENTS 1. Introduction���������������������������������������������� 1 2. Applications��������������������������������������������� 1 3. Package Contents���������������������������������� 1 4. System Requirements������������������������������ 1 5. Features���������������������������������������������������� 2 6. Hardware Description����������������������������� 3 6.1 Front Panel������������������������������������������3 6.2 Rear Panel�������������������������������������������4 7. Remote Control���������������������������������������� 5 8. RS-232 Protocols�������������������������������������� 6 8.1 Pin Assignment�����������������������������������6 8.2 Commands�����������������������������������������6 9. Connection and Installation������������������� 7 10. Specifications���������������������������������������� 8 11. Acronyms����������������������������������������������� 8
1. INTRODUCTION This is five input and one output HDMI switcher which has MHL (Mobile High-Definition Link) support integrated on its fifth input port. With the MHL port, you can share high definition video and audio from any of your MHL-ready mobile devices on an HDTV, and charge the connected device at the same time. This switcher support 3D 2.25Gbps bandwidth, 12-bit Deep Color, Hi-Def lossless audio and other features defined by HDMI v1.3 specifications, on all of its 5 input ports. The operation of source selection can be done easily through on-panel buttons, IR remote control, or RS-232 protocol.
2. APPLICATIONS • Smart Home Entertainment • Show room or meeting room • Smart AV Installation
3. PACKAGE CONTENTS • 5 by 1 HDMI with MHL switcher • 12V DC power supply adaptor • Remote Control CR-113 with battery • Operation Manual • IR Receiver cable • MHL to HDMI cable
4. SYSTEM REQUIREMENTS • HDMI sources such as PS3 or Blu-ray player for 1 to 5 ports HDMI type A inputs and the 5th port can connect to MHL mobile device with a MHL to HDMI cable. • Output HDMI type A port connect to the HDMI display/TV. Input sources with HDMI/DVI connector or MHL device.
1
5. FEATURES • With Silicon Image’s new InstaPort Technology™ • Supports five HDMI type A with one MHL to HDMI port • Supports one HDMI type A output • Supports video resolution up to 1080p@60Hz • MHL port can charge the connected mobile device • Support HDMI specification features, including data rates up to 2.25Gbps, 12-bit Deep color • Supports 3D • MHL port support 1080p@30Hz or 1080p@60Hz
2
6. HARDWARE DESCRIPTION 6.1 Front Panel
5X1 HDMI/MHL FAST SWITCHER CFSW-51MHL
1
1
POWER
INPUT
2
3
2
4
5
3
1 IR Remote Control Sensor 2 Input selection with LED:
Press input button to select input source, the Blue LED will illuminate accordingly. 3 Power button:
Press this button to switch on the device or press it again to set it to standby mode. When the system is switch to on the green LED will illuminate.
3
6.2 Rear Panel 1
HDMI IN
RS232 IR IN
HDMI OUT
2
3
1
2
3
4
MHL/HDMI 5
4
DC 12V
5
1 RS232:
This slot is to connect with a PC or control system with D-Sub 9pin cable for RS-232 control. For detail RS-232 commands please refers to section 9. 2 IR IN:
Infrared control in port for included infrared receiver cable. 3 HDMI OUT:
Connect your LCD TV or HD monitor with HDMI cables. 4 HDMI IN:
Connect the equipments to the HDMI input ports 1 to 5 such as DVD player, Blu-Ray, PS3 and other sources with HDMI cable. Especially for port 5 can connected to MHL mobile device, through the port 5 also allows charging the mobile device battery. 5 Power:
4
Plug the DC 12V power supply into the system and connect the adaptor to AC wall outlet.
7. REMOTE CONTROL 1 Power button:
Press this button to switch on or turn the device to standby mode. 2 HDMI 1~8:
This buttons are the input HDMI hot switching keys for selecting HDMI sources. Note: for this model on 1~5 is active. 3 Mute / Vol + / Vol -:
These buttons are to control the input source including DVD or PS3 or Blu-ray or even MHL mobile’s volume by set it to mute or add up or down the sound. 4
1 2
HDMI 1
HDMI 2
HDMI 3
HDMI 4
HDMI 5
HDMI 6
HDMI 7
HDMI 8
Vol +
3
Mute
Vol -
Input
Menu
6
Exit
8
4 5
Enter
7
CR-113
: These buttons are to control the input source including DVD or PS3 or Blu-ray or even MHL mobile’s play list by set it to backward, play/pause and forward.
5 Input:
Press this button sequentially to select input source from 1 ~ 5. 6 Menu:
Press this button to enter into the input source including DVD or PS3 or Blu-ray or even MHL mobile’s root menu. 7 ▲▼◄►
& Enter:
These buttons are to control the input source including DVD or PS3 or Blu-ray or even MHL mobile’s OSD selection.
Note: In order to activate the functions 3~6, input source device must compliance with the following
1.
HDMI control (CEC/Via Link…etc) must switch on.
2.
Must accept CEC command
8 Exit:
Press this button to exit the selection .
5
8. RS-232 PROTOCOLS 8.1 Pin Assignment CS-801H
Remote Control
PIN
Assignment
PIN
Assignment
1
NC
1
NC
2
Tx
2
Rx
3
Rx
3
Tx
4
NC
4
NC
5
GND
5
GND
6
NC
6
NC
7
NC
7
NC
8
NC
8
NC
9
NC
9
NC
► ◄
Baud Rate: 19200bps Data Bit: 8 bits Parity: None Flow Control: None Stop Bit: 1
8.2 Commands Command
Action
POWER 00
Power Off (standby)
POWER 01
Power On
PORT 01
Output Select Input 1
PORT 02
Output Select Input 2
PORT 03
Output Select Input 3
PORT 04
Output Select Input 4
PORT 05
Output Select Input 5
6
AUTO 00
AUTO switch off
AUTO 01
AUTO switch on
ISP 01
Software ISP process
RCP 00-7f
(RCP(remote command protocol) command)
9. CONNECTION AND INSTALLATION OR
OR
HDMI
HDMI IN
RS232 IR IN
1
HDMI OUT
2
3
4
MHL/HDMI 5
DC 12V
HDMI IR Receiver HDMI
HDMI
DVD
HDMI
DVD
HDMI
Set-top Box
Blu-ray
7
10. SPECIFICATIONS Input Ports
5 x HDMI type A connector ( 1 x MHL to HDMI type A connector
Output port
1 x HDMI
ESD Protection
Human body model:
±8 kV (air-gap discharge) ±4 kV (contact discharge)
Dimensions (mm)
240(W) x 110(D) x 49(H)
Weight(g)
792
Chassis Material
Metal
Silkscreen Color
Black
Operating Temperature
0˚C~40˚C / 32˚F ~ 104˚F
Storage temperature
-20˚C~60˚C / -4˚F ~ 140˚F
Relative Humidity
20~90% RH (no condensation)
Power Consumption (W)
2.35W
Storage Temperature
−20 °C~60 °C/−4 °F~140°F
Relative Humidity
20~90 % RH (non-condensing)
Power Consumption
3.8 W
11. ACRONYMS ACRONYM
COMPLETE TERM
MHL
Mobile High-Definition Link
8
9
10
11
CYPRESS TECHNOLOGY CO., LTD
Home page: http://www.cypress.com.tw
