Transcript
D/A Converter NANO-D1 Instruction Manual Thank you for purchasing Olasonic products. For your safety, please read the instruction manual carefully and then be sure to keep it a place where you can read it anytime.
070-0012-00
Checking the accessories Please check the accessories described below □AC adapter (TW-AC3) □AC power cable □Adapter plug (3.5mm to 6.3mm) □USB cable □Instruction Manual (this manual) Warnings 警告及び注意 and Cautions 1. Should you notice an abnormality or malfunction of the appliance, immediately stop using it and contact the purchased store or Olasonic Support Center. 2. Do not use other than the supplied AC adapter. 3. Do not touch the AC adapter with wet hand. It may cause an electric shock. 4. If the appliance is not used for an extended period of time, please disconnect the AC adapter from the AC outlet. 5. Do not disassemble the appliance. 6. Do not place the appliance in the following locations. (a) Very humid such as a bathroom (b) Places subject to rain or mist (c) Places subject to the direct sunlight such by the window (d) Places getting high temperature such as heating appliances (e) Very dusty places ( f) Unstable places 7. Make sure the plug of the cable is firmly connected to the appliance. 8. Do not pull the cable when disconnecting the cable from the appliance. 9. Do not wipe the exterior using such as benzine or thinner.
FCC Notice – Declaration of Conformity Information This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna - Increase the separation between the equipment and the receiver - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected - Consult the dealer or an experienced radio/TV technician for help Changes or modifications made to this equipment, not expressly approved by Towa Electronics Co., Ltd. for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
On cleaning If the surface of the main unit gets dirty, please wipe it using a soft cloth with mild detergent.
2
3
Connecting to the other devices NANO-CD1 or other Digital Audio Devices
NANO-CD1 or other Digital Audio Devices
Digital output
Digital output
(COAXIAL)
(OPTICAL)
Digital cable (COAXIAL)
Connecting the AC power code Computer
① Connect the spectacle-shaped plug of the supplied AC power cord to the supplied AC power adapter. ② Insert the DC output plug of AC power adapter into the DC IN terminal of this device.
Digital cable (OPTICAL)
③ After all connections are finished, insert the AC power plug into a wall outlet.
Supplied USB cable
Wall outlet
③
② Supplied AC power adapter
RCA Stereo Mini Conversion cable
or
Analog input (LINE IN)
Supplied AC power cable
RCA audio cable
Power Amplifier or Powered Speaker
USB input terminal (USB) Connect an USB port of Computer to this terminal with the supplied USB cable.
Listening to better sounds For better sounds, match the polarity of power code with the polarity of the wall outlet. - Insert the spectacle-shaped plug of AC power cable with the printing side down into the AC power adapter with the top side up(the label side down).
Optical digital audio input terminal (OPT)
Facing the top side up
Connect an optical digital audio output terminal of other device to this terminal.
Wall outlet
AC power adapter GND side
Coaxial digital audio input terminal (COAX) Connect a coaxial digital audio output terminal of other device to this terminal. 底面
Analog audio output terminal (LINE OUT) Connect these terminals to analog input terminals of other device.
4
①
Plug with the printing side down The bottom side has convex parts.
5
Name of parts and functions (Main unit) A
B
C
Basic operation E
D
1. Press the power button to turn on the main unit.
2. Select an input device by the input select button.
A. Power button ( ) Turn the main unit on and off. When the power is off, the standby indicator lights up. B. Input selector Input switches each time this button is pressed. C. Headphone terminal It enables to enjoy music with a headphone. D. Input signal indicator It shows the sampling rate of input digital signal. E. Volume knob Use to adjust the headphones output volume and the output level from the analog LINE OUT terminals.
F
F. Headphone impedance selector Select LOW if the headphone impedance is lower than 100 ohms, and select HIGH if it is higher than 100 ohms. 6
USB 96(*1)→USB 192(*2)→OPT→COAX *1 It is able to play back audio files with the sampling rate up to 96kHz on a computer. A standard driver is installed automatically on the computer. *2 It is able to play back audio files with the sampling rate up to 192kHz on a computer. If you use Windows OS, you must first install an exclusive driver on the computer. Please download this driver from the following web address. http://www.olasonic.us/
3. Start playback of the input device. Tips
・When there's no input signal, no input signal indicator lights up, ・When the input signal is lower than 44.1kHz, the input signal indicator of 44.1kHz lights up. ・When any audio signal is not output from a device selected by Input selector (except for "USB" ) and also any operation for the main unit is not done for approximately 30 minutes, the power of the unit automatically turns off. As for "USB " input, when the playback on a computer is in stop mode and any operation for the main unit is not done for approximately 30 minutes, the power of the unit automatically turns off.
4. Adjust the volume.
7
Playing music on a Computer (using the standard driver) 1. Connect a computer and the main unit with an USB cable.
Setting up a computer using the standard driver For Windows 8
Computer
1. Click [Desktop] from the Start screen. 2. Press [Windows] key and [X] key simultaneously. 3. Click [Control Panel]> [Hardware and Sound]> [Sound]> [Playback] and choose “USB2.0 Digital Audio Device”. 4. Click [Set Default]
USB cable( supplied)
2. Turn on the computer.
5. Click [Property]> [Detail] and choose the sampling rate and the bit rate of a played music file from the [Standard modes]. Then click [OK]. 6. Click [OK] to close the screen.
For Windows Vista/7
1. Click [Start]> [Control Panel]> [Hardware and Sound]> [Sound]. Click [Playback] tab and choose “USB2.0 Digital Audio Device”.
3. Press
to turn on the main unit.
2. Click [Set Default]. 3. Click [Property]> [Detail] and choose the sampling rate and the bit rate of a played music file from the [Standard modes]. Then click [OK]. 4. Click [OK] to close the screen.
4. Press the input select button to select “USB 96”. Standard driver is installed automatically on the computer.
For Mac OS
1. Select [System Preferences] from the Apple drop-down menu. 2. Click [Sound] to open the “Sound” window and select [Output] at the top of the window. 3. Select [SPDIF Output] in the list box, and close the window.
5. Set up the computer according to the page of [Setting up a computer using standard driver].
4. Click the desktop screen to activate the Finder. 5. Click [Go] from the menu bar, and select [Utilities]. 6. Click [Audio MIDI Setup].
6. Start playback of music files on the computer.
7. Select [SPDIF Output] from the items on the left side of [Audio Devices] screen, then choose the sampling rate and the bit rate of a played music file on the [Format] column. 8. Close the screen.
8
9
Playing music on a Computer (using the exclusive driver) 1. Connect a computer and the main unit with an USB cable.
Setting up a computer using the exclusive driver If you use Windows OS, you must first install an exclusive driver on the computer.Please download this driver from the following web address.
Driver software download page http://www.olasonic.us/download.html 1. Open the download page on the above website, and download the driver for NANO-D1.
USB cable( supplied) Computer
2. Turn on the computer.
2. Unzip the driver folder and install the driver by double-clicking “Setup.exe”. 3. After the installation of the exclusive driver, please make OS-wise setup as follows.
For Windows 8 3. Press
to turn on the main unit.
1. Click [Desktop] from the Start screen. 2. Press [Windows] key and [X] key simultaneously. 3. Click [Control Panel]> [Hardware and Sound]> [Sound]> [Playback] and choose “Olasonic USB DAC(HD)”.
4. Press the input select button to select “USB 192” .
4. Click [Set Default]. 5. Click [Properties]> [Advanced] and choose the sampling rate and the bit rate of a played music file from the [Default Format]. Then click [OK]. 6. Click [OK] to close the screen.
5. Set up the computer according to the page of [Setting up a computer using exclusive driver]. 6. Start playback of music files on the computer.
For Windows Vista/7 1. Click [Start]> [Control Panel]> [Hardware and Sound]> [Sound]. Click [Playback] tab and choose “Olasonic USB DAC(HD)”. 2.Click [Set Default]. 3. Click [Properties]> [Advanced] and choose the sampling rate and the bit rate of a played music file from the [Default Format]. Then click [OK]. 4. Click [OK] to close the screen.
10
11
Troubleshooting
Setting up a computer using the exclusive driver (Contd.) For Mac OS 1. Select [System Preferences] from the Apple drop-down menu. 2. Click [Sound] to open the “Sound” window and select [Output] at the top of the window. 3. Select [SPDIF Output] in the list box, and close the window. 4. Click the desktop screen to activate the Finder. 5. Click [Go] from the menu bar, and select [Utilities].
If you experience a problem with this unit, please check the following items before requesting service. If it still doesn't operate correctly, contact the retailer you purchased the unit, or send an e-mail to Olasonic support center (see the warranty information in this manual). Symptoms The power does not turn on. No sound is output.
Causes Countermeasures The power adapter or power cable Connect them correctly. is not connected correctly. C o m m o n
6. Click [Audio MIDI Setup]. 7. Select [SPDIF Output] from the items on the left side of [Audio Devices] screen, then choose the sampling rate and the bit rate of a played music file on the [Format] column. 8. Close the screen.
12
U S B
The volume is too low. The digital output setting of an input device is not set to “PCM”. The input selection is wrong.
Turn the volume up moderately. Set the digital output setting of the device to “PCM”. Select the correct input by input selection button.
The cable from input device or to output device is not connected correctly.
Connect it correctly.
The sound output setting on the computer is not correct.
Change the setting to [USB2.0 Digital Audio Device] or [Olasonic USB DAC (HD)] or [SPDIF Output].
The volume level on the volume control setting on a PC is low. The volume muting on a PC is on.
Click the volume icon on the taskbar and turn the volume moderately. Click the volume icon on the taskbar and cancel the volume muting.
The driver is not installed correctly on a PC. *In case it is not recognized on [Device Manager], “?” or “！” will appear.
Re-install the driver. *Perform the operation of [Right click] -[Delete], and reconnect the device. If not recognized after all, restart the PC with connecting the USB cable.
13
Specification Audio input
USB(B-Type), OPT(Optical digital),COAX(Coaxial digital),
Audio output
LINE(analog RCA L/R),Max 7.5Vrms
Supported sampling
USB/COAXIAL : up tp 192kHz/24bit(Linear PCM)
frequency
OPTICAL : up to 96kHz/24bit(Linear PCM)
USB compatibility
Mac OS X10.6.4 or later Windows Vista / 7 / 8
Headphone output
140mW＋140mW(300Ω),Standard 6.3mm stereo jack
Frequency characteristic 5Hz-80,000Hz Power supply
AC100V-240V(using AC power adapter)
Power consumption
Approx.4.5W(at silent)
External dimensions
149mm(W)×33mm(H)×149mm(D)(not including protrusion) 149(w) × 39(H) × 170mm(D)
Total weight
890g(main body only)
Supplied accessories
AC adapter, AC power cable, USB cable, Adapter plug(3.5mm to 6.3mm)
*The product specifications and the design are subject to change without notice.
The description of this manual is as of April,2014.
Trademark ・MAC OS is the trademark of Apple Inc. registered in U.S. and the other countries. ・Microsoft and Windows,Windows Vista, Windows7, Windows8 are the trademarks of Microsoft corporation in U.S. and the other countries. ・Microsoft and the logo, Windows, Windows logo are the trademarks of Microsoft Corporation in U.S. and the other countries.
WARRANTY INFORMATION WHO IS PROTECTED BY THIS WARRANTY The Olasonic warranty protects the original owner and all subsequent owners, provided that the product was purchased from a dealer who was authorized by Olasonic to sell such products at the time of the original purchase. A copy of the original dated bill of sale must be presented whenever warranty service is required.
WHAT IS COVERED BY THIS WARRANTY
Except as specified below, the Olasonic warranty covers all defects in material and workmanship for one year from the date of the first consumer purchase. The followings are not covered; damage caused by accident, misuse, abuse, product modification or neglect; damage occurring during shipment; damage from failure to follow instructions contained in the instruction manual; damage resulting from the performance of repairs by someone not authorized by Olasonic; damage caused by installation of parts that does not conform to Olasonic specifications; units not used for their intended purpose; any claims based on misrepresentations by the seller; products sold on an “as is “ or final sale basis; or the cost of installing, removing or reinstalling the unit. Olasonic liability is limited to the repair or replacement, at our option, of any defective product and shall not include incidental or consequential damages. Olasonic reserves the right to replace a discontinued model with a comparable model. Any replacement units or parts may be new or rebuilt. NOTE: Repair of our product must be done by an authorized dealer, distributor or service center. Unauthorized repair will void the warranty and is done at the risk of the consumer.
TO OBTAIN WARRANTY SERVICE
Warranty service is only available in the country of original purchase. If you require warranty service, please contact your dealer or distributor for assistance. If it is not possible, please send an e-mail to
[email protected] for information on how to obtain service or replacement.
This warranty gives you specific legal rights. You may also have other rights, which vary country to country, or state to state. Some countries or states do not allow the exclusion or limitation of incidental or consequential damages or limitations on how long an implied warranty lasts, so, the above may not apply to you.
14
15
