Transcript
D/N VANDAL RES. VARI-FOCAL DOME CAMERA PIH-2342X/2346X W/S
MERIT LILIN ENT. CO., LTD http://www.meritlilin.com
66-234CSE
INSTRUCTION MANUAL
IMPORTANT SAFEGUARDS CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN
CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
GRAPHIC SYMBOL EXPLANATION The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the unit.
PART DESCRIPTION & DIMENSION 136.0
55.0 99.5
Unit mm
BASE DOME COVER HOLE PLUG SIDE HOLE
INSTALLATION 1. Please use the enclosed screw driver to untighten the 4 tamper-proof screws on the dome cover. 2. Put the provided screws (M3.0 x 25, wooden screw) through the holes marked as "a", and fix the base in the desired area (FIG.1). a a
a FIG. 1 3. Firstly, put video cable and power cable through a pipe with 1/2" PT at one end (FIG.2), and connect the cables to the terminal block on the PCB accordingly and then screw the pipe to the side hole (FIG.3, please make sure the connection between the pipe and the side hole is watertight.). NOTE : Pipe is not provided. R WE PO PUT GND IN EO OUT D VI DEO VI
FIG. 2
FIG. 3
4. The direction of the lens is adjustable through the adjustable Pan/Tilt brackets and rotatable round bracket for Azimuth. The lens can be adjusted easily by hand without using screw driver. Please refer to FIG.4.
IRIS LEVER VR SCREW DRIVER
TILT
BRACKET
AZIMUTH
ZOOM OR FOCUS ADJUSTMENT FOCUS OR ZOOM ADJUSTMENT PAN
FIG. 4 5. An extra RCA jack for easy installation. Plug the video input of monitor to the RCA jack and adjust focus and zoom. After finished, unplug the RCA jack. Please refer to FIG.5.
FIG. 5
6. Adjust DC iris level by turning the iris level VR. Please refer to FIG.4. ATTENTION: Adjust this VR with care so as not to cause damage to the unit. 7. Put on the dome cover first. Then tighten the tamper-proof screws (FIG.6).
FIG. 6
Alternative cabling positions 1. Untighten the hole plug on the bottom of the base and screw it to the side hole.
2. Put the video cable and power cable through the bottom hole and connect them to the terminal block on the PCB accordingly. Please refer to INSTALLATION Step3 for waterresistant installation. 3. Fix the cable with cable clamp. R WE PO PUT GND IN EO OUT D VI DEO VI
SPECIFICATIONS D/N VANDAL RESISTANT VARI-FOCAL DOME CAMERA PIH-2342XWN/P
Model No.
PIH-2342XSN/P
3.3~12mm
Focal Length
9~22mm F1.4
Iris Lens Angle of view
H
89.8 ~ 23.9
V
63.6 ~ 17.9
32.1 ~ 13.1 23.3 ~ 9.8
D
125.7 ~ 29.9
41.9 ~ 16.3 DC12V ( 10%)
Power Input Voltage System
NTSC or PAL Internal
Sync. Mode Pick Up Element
1/3" Super HAD CCD Sensor
Effective Pixels
768(H) x 494(V) [NTSC] 752(H) x 582(V) [PAL]
Chip Size Horizontal & Vertical Sync. Frequency
5.59mm (H) x 4.68mm (V) 15.734KHz / 59.94Hz [NTSC] 15.625KHz / 50Hz [PAL] 2
Scanning System Infrared Cut Filter Resolution Minimum Illumination S/N Ratio
1 Interlace
Auto Selectable Automatic Switch From Color Mode To Monochrome Color: 540TV Lines, Mono: 600TV Lines Color: 0.05Lux at F1.4, 0Lux with IR Mono: 0.01Lux at F1.4 More Than 50dB (AGC OFF) 36dB Variable Gain
Auto Gain Control White Balance
ATW
Aperture Correction
Horizontal , Vertical
Power Consumption
2.2W Auto
Back Light Compensation
CVBS 1.0Vp-p , 75ohm
Video Output Operating Temperature
-10
IP Rating Vandal Proof Dimension Weight
~ +50
(14
~ 122
)
=0.45
Gamma Characteristic
IP68 Withstand a blow from a 10 lbs sledgehammer Base :
136 x 55mm , Dome :
91.8
1200g
Design and specifications are subject to change without notice.
D/N VANDAL RESISTANT VARI-FOCAL DOME CAMERA PIH-2346XWN/P
Model No.
PIH-2346XSN/P
3.3~12mm
Focal Length
9~22mm F1.4
Iris Lens Angle of view
H
89.8 ~ 23.9
V
63.6 ~ 17.9
23.3 ~ 9.8
D
125.7 ~ 29.9
41.9 ~ 16.3
Power Input Voltage System
32.1 ~ 13.1
DC12V ( 10%) or AC24V ( 10% ) NTSC or PAL Internal
Sync. Mode Pick Up Element
1/3" Super HAD CCD Sensor
Effective Pixels
768(H) x 494(V) [NTSC] 752(H) x 582(V) [PAL]
Chip Size Horizontal & Vertical Sync. Frequency
5.59mm (H) x 4.68mm (V) 15.734KHz / 59.94Hz [NTSC] 15.625KHz / 50Hz [PAL] 2
Scanning System Infrared Cut Filter Resolution Minimum Illumination S/N Ratio
1 Interlace
Auto Selectable Automatic Switch From Color Mode To Monochrome Color: 540TV Lines, Mono: 600TV Lines Color: 0.05Lux at F1.4, 0Lux with IR Mono: 0.01Lux at F1.4 More Than 50dB (AGC OFF) 36dB Variable Gain
Auto Gain Control White Balance
ATW
Aperture Correction
Horizontal , Vertical
Power Consumption
3.0W (DC12V) , 2.5W (AC24V) Auto
Back Light Compensation
CVBS 1.0Vp-p , 75ohm
Video Output Operating Temperature
-10
IP Rating Vandal Proof Dimension Weight
~ +50
(14
~ 122
)
=0.45
Gamma Characteristic
IP68 Withstand a blow from a 10 lbs sledgehammer Base :
136 x 55mm , Dome :
91.8
1200g
Design and specifications are subject to change without notice. 66-234CSE-3
D/N VANDAL RES. VARI-FOCAL DOME CAMERA PIH-2342X/2346X W/S
MERIT LILIN ENT. CO., LTD http://www.meritlilin.com
66-234CSE
INSTRUCTION MANUAL
