Transcript
D1U-52-CONC
www.murata-ps.com
D1U-52 Connector Card Application Note PRODUCT OVERVIEW This Output Connector card can be used to connect the D1U-H power supply for bringing out the output voltage and signals for bench evaluation. Customers can also use this card as an interface to their applications.
SAFETY PRECAUTION
This D1U-52-CONC output connector card is intended to facilitate the connection for the user to evaluate the D1U-H power supply in the laboratory by qualified personnel There is 200Vac and 52V exposed on this output connector card, please take the necessary safety precautions during your product evaluation. SCHEMATIC - D1U-52-CONC
-52VDC OUT
P4
DC2
-52VDC OUT
P5
DC3
-52VDC RTN
P6
DC4 P7
J12
1 3 5 7 9 11 13 15
TP15
1 2
JUMPER JUMPER D1 -SNS C1 +SNS B1 GND A1 SHORT PIN 2 D2 1 PRESENT_L 2 C2 J13 B2 I2C_ADR0 2 JUMPER A2 D3 I2C_ADR3 C3 I2C_ADR2 B3 A3 12V_AUX D4 C4 I2C_CLOCK B4 I2C_ADR1 A4 D5 I2C_DATA 2 C5 B5 J14 A5 I2C_EN_H D6 2 C6 I_SHARE R10 N/F TP7 B6 DC_OK_L A6 PS_ENB_LOW 2
1/4 STUD
2 4 6 8 10 12 14 16
J15 16PIN
2
DUAL ROW RIBBON CONNECTOR FOR MONITORING O/P
3V3/5V
J9 J10
#6-32 STUD TP16 J8
1 2
J18 J19
PHOENIX CONNECTOR
R5
N/F
I2C_ADR1
R6
N/F
I2C_ADR2
R7
N/F
R8
N/F
I2C_ADR0
I2C_ADR3
#6-32 STUD
12V_AUX
TP3
1 2
J16
TP1 PAD
2
TP17 FOLLOWING COMPONENTS ARE NOT FITTED R5, R6, R7, R8, R10 J8, J9, J10, J14,J15, J16, J18, J19 TP1, TP3, TP7
1 2
J1 31PIN
J11
1 2
R13 0R00
1 2
J1 31PIN
12V_AUX
1 2
DC1
D1
JUMPER
1 2 3 4 5 6 7 8 9 10 11 12
-52VDC RTN -SNS +SNS P_ENABLE PRESENT_L DC_OK_L I2C_EN_H I_SHARE
1 2
J1 31PIN
PS_ENB_LOW
TP11 CABLES FROM TP12 RECEPTACLES TP13 1/4 STUD TP14
P1
2
1 2
AC_IN1 AC2 AC_IN2 P2 AC3 SFTY_GND P3 AC1
IN4148
J7 12PIN
R12 0R00
S2 2A 2
For full details go to www.murata-ps.com/rohs
www.murata-ps.com/support 13 Nov 2012 ACAN-28.A02 Page 1 of 3
D1U-52-CONC D1U-52 Connector Card Application Note SIGNAL SPECIFICATION High Level Low Level
Pin Assignment
Signal Name
Description
D2
P_Good
Power good signal output (Internal pull up is 5kΩ to Vsb)
A1
+SENSE1
VOUT remote sense, positive node input, connected to the +ve load point
A2
-SENSE1
VOUT remote sense, negative node input connected to the -ve load point
A6
PS_ON
Internal 1K ohm pull-up to Vsb, (accepts open collector/ drain >2.1V (open, or Vsb) <0.7V -1 mA -4 mA drive), This signal to be pulled low to turn-on power supply (active, PS:On)
B5
PS_Kill
Floating pin will turn off P/S (shorter pin, last-make and first-break contact for hot plugging). This signal overrides PS-On in disabling the main output
>2.1V <0.7V N/A (open, or Vsb) (active, PS:On)
Present
Internally tied to Vsb return
0V
N/C
No Connection
N/C
No Connection
N/C
No Connection
D1
AC_OK
Input AC Voltage “OK” signal output (Internal pull up is 5kΩ to Vsb)
C5, C6, D5, D6
V_SB
Standby voltage output
B6
I Max
>2.4V (active, Good) <0.4V -2 mA +4 mA
>2.4V (active, OK) <0.4V
-2 mA +4 mA
There is a jumper already installed between PS_Kill and Gnd . There is a switch already installed to toggle the PS_ON to Gnd for enabling the power supply.
www.murata-ps.com/support 13 Nov 2012 ACAN-28.A02 Page 2 of 3
D1U-52-CONC D1U-52 Connector Card Application Note
J19 J14 J13
I_SH
CLK
GND
2
1
PRESENT
I2C_EN
J17
J7 1
J11 -SNS to -52VDC OUT J12 +SNS to -52VDC RTN J13 PRESENT_L to GND J14 I2C_EN_H TO GND J16 VIN for I2C
12V_AUX
GND R13
P_EN GND
DC_OK VIN
ADR2 ADR3
ADR1
ADR0
-SNS
+SNS
R10
R8
J9
J10 J18
-52VDC_RTN (GND)
J15
D1
R7
R5
-52VDC_OUT
R12
16
PS_ENB_LOW J16 R6
J8 1
J11
15
S2
J12 "OFF"
I_SHARE
"ON"
D6 D5 D4 D3 D2 D1
DATA
A1
A6
DC1
DC2
DC3
DC4
-52VDC OUT
-52VDC RTN (GND)
MECHANICAL DIMENSIONS - D1U-52-CONC
12V_AUX GND 12V_AUX I2C_CLK V3/5V DATA GND
J100
Dimensions: 3" x 5.5"
Murata Power Solutions, Inc. 11 Cabot Boulevard, Mansfield, MA 02048-1151 U.S.A. ISO 9001 and 14001 REGISTERED
This product is subject to the following operating requirements and the Life and Safety Critical Application Sales Policy: Refer to: http://www.murata-ps.com/requirements/ Murata Power Solutions, Inc. makes no representation that the use of its products in the circuits described herein, or the use of other technical information contained herein, will not infringe upon existing or future patent rights. The descriptions contained herein do not imply the granting of licenses to make, use, or sell equipment constructed in accordance therewith. Specifications are subject to change without notice. © 2012 Murata Power Solutions, Inc.
www.murata-ps.com/support 13 Nov 2012 ACAN-28.A02 Page 3 of 3
