Transcript
Data sheet
DA1001
MidspanUPS SecurePoE
A power over Ethernet midspan power supply with secure enclosure and monitoring. Every SecurePoE unit complies with the IEEE 802.3:2012 standard (IEEE 802.3at/IEEE 802.3af). SecurePoE units will provide the full 30W of power to every port. All units are housed in secure tamper protected cases. MidpanUPS SecurePoE power supplies are fitted with Yuasa battery packs to maintain power to connected PoE devices during mains failure. One, two or four output wall mount versions are available in secure indoor or exterior enclosures. Rack-mount versions are available with 4 or 8 ports per unit. Rack versions have a remote battery pack to allow the MidspanUPS to remain in a 1U profile. Battery packs can be mounted remotely from the rack where space is available. Each output has an RJ45 data port, (e.g. from the network switch) and an RJ45 load port for the PoE device, that outputs the data and power. Outputs have LED indication to show if a compatible device is connected and powered. In addition there are SPCO clean contacts for monitoring the power status of each output. The units also have power on LED indication and SPCO clean contacts to signal power failure and low battery voltage; as well as battery disconnect deep discharge protection. Output Ports
DA1001-IN-1 DA1001-EX-1 -
DA1001-IN-2 DA1001-EX-2 -
DA1001-IN-4 DA1001-EX-4 DA1001-RM-4
DA1001-RM-8
1 x 30W
2 x 30W
4 x 30W
8 x 30W
Voltage
55V DC (nominal)
Current
Maximum 0.55A (30W) per port
Connection type
RJ45 - Plug & play
Status indication
LED indication; Flashing = PoE device connected, no power requested On = PoE device connected, power enabled Off = PoE device not detected
Compatibility
IEEE 802.3:2012 (IEEE 802.3at & IEEE 802.3af, full backward compatibility)
Data rate
DA1001-x-x
DA1001-x-x-G
10BASE-T 100BASE-TX
10BASE-T 100BASE-TX 1000BASE-T (Gigabit)
Power class detection
Automatic class 0, 1, 2, 3, 4 detection
Mode
Mode B (Delivers power over spare pairs on 10/100 networks only)
Monitoring contacts – (individual output status & unit power fault switching) Contact configuration
Single pole change over
Rating
Maximum switching AC/DC 30V 1A
Connection type
Rising clamp PCB terminal block (2.5mm²)
Battery low voltage signalling threshold
46V (nominal)
Battery low voltage disconnect threshold
42.5V (nominal)
Input Voltage
90-270V AC, 47-63Hz
Power consumption
≤ 132VA - Built-in active PFC function, PF>0.96
Connection type
Fused Mains on indication
DA1001-IN-x DA1001-IN-x-G
DA1001-EX-x DA1001-EX-x-G
DA1001-RM-x DA1001-RM-x-G
10mm² internal terminal block (3 x 1.5mm² or 2 x 2.5mm²)
C14 IEC connector (Kettle lead)
3A Mains 1” fuse (BS1362)
6.3A Mains QB 20 x 5mm Glass fuse
LED indication
Neon indicator
The enclosed information is believed to be correct. Information may change ‘without notice’ due to product improvement. Users should ensure that the product is suitable for their use. E&OE. Registered Proprietor: Benham (General Engineers) Ltd (No. 1181752) Registered at 3 Galliford Road Industrial Estate, Heybridge, Maldon, Essex CM9 4XD, UK. Directors: R.A.Scott, K.E.Horwood, T.J.Scott, N.J.Scott. VAT Reg. GB 28276273 Tel:+44(0)1621 856 850 Fax:+44(0)1621 856 162
[email protected] Page 1 - 2 Revision EN_15-01-20-12-29-42
Data sheet
DA1001
MidspanUPS SecurePoE
Environmental Operating temperature
-10°C to +40°C
Storage temperature
-20°C to +50°C
Operating relative humidity
Maximum 95% non-condensing DA1001-IN-x DA1001-IN-x-G
Ingress protection
DA1001-RM-x DA1001-RM-x-G
DA1001-EX-x DA1001-EX-x-G
IP20
IP66
Dimensions* DA1001-IN-x DA1001-IN-x-G
DA1001-EX-x DA1001-EX-x-G
DA1001-RM-x DA1001-RM-x-G (Excluding remote battery pack.)
Width
250mm
280mm
478mm (19” Rack-mount)
Height
330mm
340mm
44mm (1U)
Depth
125mm
130mm
380mm (15”)
Weight
≤ 5.3Kg
≤ 4.9Kg
≤ 5Kg
Mild steel
Acrylontrile Butadiene Styrene (ABS)
Mild steel
Powder coated White RAL9016
Grey RAL9003
Powder coated Black RAL9005
Enclosure material Finish Battery pack *Note: Rack-mount versions with 4 ports have one battery pack Rack-mount versions with 8 ports have TWO battery packs
Indoor
Exterior
Rack-mount
(DA1001-IN-x)
(DA1001-EX-x)
(DA1001-RM-x)
DA1001-IN-BATT
DA1001-EX-BATT
DA1001-RM-BATT
1.2Ah
1.2Ah
1.2Ah
Width
240mm
240mm
205mm
Height
100mm
100mm
100mm
Depth
60mm
60mm
148mm
Weight
2.7Kg
2.7Kg
2.9Kg
Replacement battery pack code VRLA battery capacity
Other Estimated MTBF
50,000 hours
CE Approved
Yes
Tamper switch
Yes
•
Other battery pack capacities available, e.g. DA1007 & DA1010. Please see chart to calculate your requirements.
Estimated stand-by times Output load
Battery capacity 1.2Ah
7Ah
10Ah
12W
4 Hours
30 Hours
44 Hours
25W
1.75 Hours
14.5 Hours
20 Hours
50W
40 Minutes
6.5 Hours
9.5 Hours
75W
23 Minutes
4 Hours
6 Hours
100W
14 Minutes
2.75 Hours
4 Hours
The enclosed information is believed to be correct. Information may change ‘without notice’ due to product improvement. Users should ensure that the product is suitable for their use. E&OE. Registered Proprietor: Benham (General Engineers) Ltd (No. 1181752) Registered at 3 Galliford Road Industrial Estate, Heybridge, Maldon, Essex CM9 4XD, UK. Directors: R.A.Scott, K.E.Horwood, T.J.Scott, N.J.Scott. VAT Reg. GB 28276273 Tel:+44(0)1621 856 850 Fax:+44(0)1621 856 162
[email protected] Page 2 - 2 Revision EN_15-01-20-12-29-42
