Transcript
Dallas DS2490 USB Adapter INSTALLATION INSTRUCTIONS
Cutting edge simplicity June 2011
Table of Contents INTRODUCTION ........................................................................................................................................... 3 SOFTWARE INSTALLATION ....................................................................................................................... 4 DRIVER INSTALLATION .............................................................................................................................. 4 Windows 98 / WINDOWS ME .............................................................................................................. 4 Windows® 2000.................................................................................................................................... 5 Windows® XP ....................................................................................................................................... 7 Windows® Vista, 7 and 2008 ................................................................................................................ 9 Special Consideration for USB Installation........................................................................................... 9 DRIVER FILES AND LOCATIONS ............................................................................................................. 10 UNINSTALLING THE DS2490 .................................................................................................................... 11 Uninstalling under Windows 2000 and Windows XP .......................................................................... 11 Uninstalling under Windows® Vista, Windows® 7 and Windows® 2008 .............................................. 12 Uninstalling under Windows® 98 and Windows ME ........................................................................... 12
© Cansec Systems Ltd., 2008 All rights reserved
Dallas DS2490 USB Adapter Installation Guide
Page 2 of 12 June 2011 • Rev. 2.2
Introduction Welcome to the Dallas DS2490 USB Adapter installation guide. The DS2490 USB Adapter allows you connect the iButton® Enrollment Reader to your computer through your computer's USB port. NOTE: SmartLock® Connect and SmartLock® Ultralite’s stand-alone controllers/readers can only be programmed using the iButton programming key and enrollment reader that is part of the Stand-Alone Programming Kit (below). This also applies to Cansec TruckStop Express controller. iButton Programming Key (Snaps into enrollment reader receptacle)
Dallas DS2490 USB Adapter (Connects to PC’s USB port)
iButton Enrollment Reader (Transports data to/from the programming modules, positioned at controllers) The iButton Enrollment Reader has a phone-style jack that plugs in to both the iButton USB adapter and the stand-alone programming module near the controller.
With the programming key snapped into the enrollment reader receptacle, data can be transported to and from controllers and the PC.
All Cansec products that support the Dallas DS2490 USB Adapter load the required drivers for operation. This document provides detailed instruction for completing the installation phase of this USB device.
Dallas DS2490 USB Adapter Installation Guide
Page 3 of 12 June 2011 • Rev. 2.2
Software Installation NOTE: Never attempt to plug the USB adapter into an available USB port until the associated access-control software has been installed.
Driver Installation Once software installation is completed, plug the Dallas DS2490 USB Adapter into a free USB socket. Do not attempt to use a USB hub interface. Driver installation occurs when the device is first detected by the system and not all USB hubs work reliably with the DS2490. For this reason, it is important to connect directly to a motherboard USB socket to ensure that the driver installation completes properly. If you mistakenly plugged the adapter in prior to software installation, see the section Uninstalling the DS2490 before proceeding. The driver installation process is determined by the version of Windows®. Sample installation scenarios are presented below for Windows 98, Windows 2000, Windows XP and Windows 7. For Windows Vista and Windows 2008 the steps are similar to that of Windows 7.
WINDOWS 98 / WINDOWS ME When the DS2490 is inserted for the very first time, the Found New Hardware popup window will appear.
After a brief interval correct identification of the USB device should take place.
Once identified, the driver will load automatically and the adapter should be ready for use.
Dallas DS2490 USB Adapter Installation Guide
Page 4 of 12 June 2011 • Rev. 2.2
WINDOWS® 2000 When the DS2490 is inserted for the very first time, the Found New Hardware popup window will appear.
After a brief interval correct identification of the USB device should take place.
If Windows is unable to locate the driver, it will prompt for the driver location.
Click Browse
Dallas DS2490 USB Adapter Installation Guide
Page 5 of 12 June 2011 • Rev. 2.2
Browse to C:\WINNT\system32\drivers\DS2490.sys
Click Open
Click OK to complete driver installation.
Dallas DS2490 USB Adapter Installation Guide
Page 6 of 12 June 2011 • Rev. 2.2
WINDOWS® XP When the DS2490 is inserted for the very first time, the New Hardware Wizard setup screen will appear. Windows Update does not support 1-wire devices at this time and also requires an active Internet connection to function. For this reason: Choose No, not this time Click Next
The Driver Installation window is then displayed. Select Install the software automatically (Recommended) Click Next
Dallas DS2490 USB Adapter Installation Guide
Page 7 of 12 June 2011 • Rev. 2.2
Typically, Windows® XP will be unable to locate the driver and the Files Needed window will be displayed.
Choose C:\WINDOWS\system32\drivers from the drop list box Or click Browse and locate the driver C:\WINDOWS\system32\drivers\DS2490.sys manually
Dallas DS2490 USB Adapter Installation Guide
Page 8 of 12 June 2011 • Rev. 2.2
The driver should be successfully located and installed.
Press Finish to complete the process.
WINDOWS® VISTA, 7 AND 2008 During the access control software installation, there will be a prompt to install the driver for the USB adapter. Follow the prompt to complete the driver installation. Once the driver and the access controls software are installed, plug the USB adapter into a USB port on the computer and it will automatically find and load the driver for the adapter. Note: A USB hub is NOT recommended.
SPECIAL CONSIDERATION FOR USB INSTALLATION The following additional points are noted in the Dallas Semiconductor device driver documentation and maybe applicable in some cases. Unplug any 1-wire USB devices during installation to allow the device driver to be updated. If a 1-wire USB device has previously been used on the PC, the computer must be restarted after installation to recognize the new device driver. If the PC has never had a 1-wire USB device on it, plug it in right after installation to complete the USB install. If it is not recognized, then restart the computer and try again. If auto-detect cannot locate the USB device driver (DS2490.SYS), browse to it in C:\WINDOWS\system32\drivers or C:\WINNT\system32\drivers. Dallas DS2490 USB Adapter Installation Guide
Page 9 of 12 June 2011 • Rev. 2.2
Driver Files and Locations The following driver and support files are loaded during installation of one of the above-mentioned products. Windows® 98, Windows ME, Windows XP, Windows Vista, Windows 7 and Windows 2008 Location
Files
C:\Windows\Inf
DS2490.inf
C:\Windows\system32
ib90usb.dll
C:\Windows\system32
ibfs32.dll
C:\Windows\system32\drivers
DS2490.sys
Windows 2000 Location
Files
C:\WINNT\Inf
DS2490.inf
C:\WINNT\system32
ib90usb.dll
C:\WINNT\system32
ibfs32.dll
C:\WINNT\system32\drivers
DS2490.sys
Dallas DS2490 USB Adapter Installation Guide
Page 10 of 12 June 2011 • Rev. 2.2
Uninstalling the DS2490 Use Add/Remove Program in Windows’ Control Panel to remove the driver whenever possible. However, uninstalling the Dallas DS2490 USB Adapter may also be performed via the Windows® Device Manager. Removal requires that the device be plugged in first so that it is accessible from Device Manager’s list.
UNINSTALLING UNDER WINDOWS 2000 AND WINDOWS XP In both Windows 2000 and Windows XP, the DS2490 is displayed as shown below.
Highlight the device Press Remove (circled in red)
The Confirm Device Removal dialog box will appear.
Click OK Restart your computer if necessary
Dallas DS2490 USB Adapter Installation Guide
Page 11 of 12 June 2011 • Rev. 2.2
UNINSTALLING UNDER WINDOWS® VISTA, WINDOWS® 7 AND WINDOWS® 2008 Use the Program and Features in the Control Panel to remove the driver
UNINSTALLING UNDER WINDOWS® 98 AND WINDOWS ME In Windows 98 and Windows ME, locate the device under the Universal Serial Bus controllers collection.
Highlight the device Click Remove
Dallas DS2490 USB Adapter Installation Guide
Page 12 of 12 June 2011 • Rev. 2.2
