Transcript
4-Port Antenna Frequency Range Dual Polarization HPBW Fixed Electr. DT
R1
B1
790–960 1710–2170 X
X
65°
60°
0°
0°
4-Port Antenna 790–960/1710–2170 65°/60° 12/14dBi 0°/0°T
742226V01
Type No. Lowband Frequency range Polarization Gain Horizontal Pattern: Half-power beam width Front-to-back ratio (180°±30°) Cross polar ratio Maindirection 0° Sector ±60° Tracking, Avg. Squint Vertical Pattern: Half-power beam width Electrical tilt
MHz ° dBi
dB dB
790 – 862 +45, –45 2 x 11.1 68 Copolar: Total power:
Ω dB dB dBc W
67 Copolar: Total power:
> 23 > 20
65 Copolar: Total power:
Typically: 25 > 10
Typically: 25 > 10 1.0 ±3.0
Typically: 25 > 10
34
33 0, fixed
30
dB ° ° °
> 23 > 20
880 – 960 +45, –45 2 x 11.8
> 25 > 22
50 < 1.5 > 30 > 42 (790 – 960 // 1710 – 2170 MHz) < –150 (2 x 43 dBm carrier) 250 (at 50 °C ambient temperature)
936.3967/f
Subject to alteration.
Impedance VSWR Isolation: Intrasystem Isolation: Intersystem Intermodulation IM3 Max. power per input
R1 790 – 960 824 – 894 +45, –45 2 x 11.4
742226V01 Page 1 of 3 www.kathrein.com KATHREIN-Werke KG · Anton-Kathrein-Straße 1-3 · P.O. Box 10 04 44 · 83004 ROSENHEIM · GERMANY · Phone +49 8031 184-0 · Fax +49 8031 184-820
4-Port Antenna
Highband Frequency range Polarization Gain Horizontal Pattern: Half-power beam width Front-to-back ratio (180°±30°) Cross polar ratio Maindirection 0° Sector ±60° Tracking, Avg. Squint Vertical Pattern: Half-power beam width Electrical tilt Impedance VSWR Isolation: Intrasystem Isolation: Intersystem Intermodulation IM3 Max. power per input
B1 MHz ° dBi ° dB dB
1710 – 1880 +45, –45 2 x 12.8 66 Copolar: Total power:
Ω dB dB dBc W
> 25 > 22
60 Copolar: Total power:
1920 – 2170 +45, –45 2 x 13.6
> 25 > 22
60 Copolar: Total power:
Typically: 16 > 10
Typically: 18 > 10 0.5 ±1.5
Typically: 20 > 10
20
18 0, fixed
17.5
dB ° ° °
1710 – 2170 1850 – 1990 +45, –45 2 x 13.3
> 25 > 22
50 < 1.5 > 30 > 42 (790– 960 // 1710 – 2170 MHz) < –150 (2 x 43 dBm carrier) 200 (at 50 °C ambient temperature)
4 x 7-16 female Bottom or top Frontal: 125 | 28 Maximal: 135 | 30 200 124 579 / 262 / 139 22.8 / 10.3 / 5.5 M (Medium) 7.5 / 9.5 (clamps incl.) 16.5 / 20.9 (clamps incl.) 756 x 282 x 172 29.8 x 11.1 x 6.8 Panel and 2 units of clamps for 42 – 115 mm | 1.7– 4.5 inches diameter
* Inverted mounting: Connector position top: Change drain hole screw.
Page 2 of 3 742226V01 www.kathrein.com KATHREIN-Werke KG · Anton-Kathrein-Straße 1-3 · P.O. Box 10 04 44 · 83004 ROSENHEIM · GERMANY · Phone +49 8031 184-0 · Fax +49 8031 184-820
936.3967/f
Input Connector position Wind load (at Rated N | lbf Wind Speed: 150 km/h) Max. wind velocity km/h mph Height/width/depth mm inches Category of mounting hardware Weight kg lb Packing size mm inches Scope of supply
Subject to alteration.
Mechanical specifications
Accessories General Information Accessories (order separately if required) Description
Remarks mm / inches
Weight approx. Units per kg | lb antenna
731651 85010002 85010003 737978
1 clamp 1 clamp 1 clamp 1 downtilt kit
Mast diameter: 28 – 60 | 1.1 – 2.4 Mast diameter: 110 – 220 | 4.3 – 8.7 Mast diameter: 210 – 380 | 8.3 – 15.0 Downtilt angle: 0° – 20°
0.8 | 1.8 2.7 | 6.0 4.8 | 10.6 2.3 | 5.1
2 2 2 1
1.1 | 2.4
2
1)
Type No.
2) 3)
1) 9 | 0.4 2) 72 | 2.8 3) 64 | 2.5
1 clamp
Mast diameter: 42 – 115 | 1.7 – 4.5
For downtilt mounting use the clamps for an appropriate mast diameter together with the downtilt kit. Wall mounting: No additional mounting kit needed. Material:
Reflector screen: Weather-proof aluminum. Fiberglass housing: It covers totally the internal antenna components. Fiberglass material guarantees optimum performance with regards to stability, stiffness, UV resistance and painting. The color of the radome is light grey. All screws and nuts: Stainless steel.
Grounding:
The metal parts of the antenna including the mounting kit and the inner conductors are DC grounded.
630 | 24.8 670 | 26.4
738546
579 | 22.8
Accessories (included in the scope of supply)
All dimensions in mm | inches
Correlation Table Frequency range
Array
Connector
790 – 960 MHz 1710 – 2170 MHz
R1 B1
1–2 3–4
B1 R1
58 | 2.3
Layout of interface:
52 | 2.0
139 | 5.5
1710 –2170 +45°
790 – 960 –45°
790 – 960 +45°
936.3967/f
Subject to alteration.
1710 –2170 –45°
262 | 10.3 Bottom view All dimensions in mm | inches Any previous data sheet issues have now become invalid.
742226V01 Page 3 of 3 www.kathrein.com KATHREIN-Werke KG · Anton-Kathrein-Straße 1-3 · P.O. Box 10 04 44 · 83004 ROSENHEIM · GERMANY · Phone +49 8031 184-0 · Fax +49 8031 184-820
Mounting Hardware Clamp Included in the Scope of Supply
Suitable for mast diameter Antenna – mast distance
(mm) [inches] (mm) [inches]
Material of clamp and screws Weight
(kg) [lb]
42 – 115 [1.65 – 4.53] 20 – 25 [0.79 – 0.98] Hot-dip galvanized steel / stainless steel 1.1 [2.43]
100 [3.94]
40 [1.57]
40 [1.57]
72 [2.83]
20–25 [0.79–0.98]
152 [5.98]
15 2–1 4 4.53] 5– [1.6
M10 MA = 25 Nm
35 [1.38]
M8 MA = 20 Nm
64 [2.52] 125 [4.92]
936.3920/c
Subject to alteration.
20–25 [0.79–0.98]
Please note: Kathrein does not recommend to use counter nuts. The additional nuts supplied are only meant as spares.
www.kathrein.de
Any previous data sheet issues have now become invalid.
All dimensions in mm and [inches]
738546 Page 1 of 1
KATHREIN-Werke KG · Anton-Kathrein-Straße 1-3 · P.O. Box 10 04 44 · 83004 ROSENHEIM · GERMANY · Phone +49 8031 184-0 · Fax +49 8031 184-820
General Information about Panel Antennas Environmental conditions:
Kathrein cellular antennas are designed to operate under the environmental conditions as described in ETS 300 019-1-4 class 4.1 E. The antennas exceed this standard with regard to the following items: – Low temperature: –55 °C – High temperature (dry): +60 °C For antennas equipped with FlexRET: The electrical downtilt adjusting is designed to operate under the environmental conditions as described in the valid data sheet of the FlexRET. Ice protection: Due to the very sturdy antenna construction and the protection of the radiating system by the radome, the antenna remains operational even under icy conditions.
Environmental tests:
Kathrein antennas fulfil the stated specifications after completion of the environmental tests as defined in ETS 300 019-2-4. The homogenous d esign of Kathrein’s antenna families uses identical modules and materials. Extensive tests have been performed on typical samples and modules. The vibration test has been adapted relating to frequency and acceleration to the conditions of mast mounted antennas.
Please note:
As a result of more stringent legal regulations and judgements regarding product liability, we are obliged to point out certain risks that may arise when products are used under extraordinary operating conditions. The mechanical design is based on the environmental conditions as stipulated in ETS 300 019-1-4. Wind loads are calculated according to DIN 1055-4. The antennas may be used at locations where the anticipated peak wind velocity or gust wind speed lies within the maximum wind speed listed in the data sheet. We warrant the mechanical safety and electrical functionality under such conditions. The wind speeds are defined in accordance with the DIN, EN or TIA standards. This warranty makes allowance for the partial safety factors specified in those standards. Extraordinary operating conditions, such as heavy icing or exceptional d ynamic stress (e.g. strain caused by oscillating support structures), may result in the b reakage of an antenna or even cause it to fall to the ground. These facts must be c onsidered during the site planning process.
936.4694/d
Subject to alteration.
The details given in our data sheets have to be f ollowed carefully when installing the antennas and a ccessories. Site planning and installation must be carried out by qualified and experienced staff. All relevant national safety regulations must be upheld and respected. Incorrect site planning, faulty installation, as well as interfering surroundings on site, may lead to deviations in the electrical parameters compared to those specified in the respective data sheets. The connectors on this product are only suitable for connecting to the compatible counterpart. Please ensure that the connected cable has been fitted with a connector of the same standard, otherwise damage may occur. The tilt values will be set to any arbitrary value in the given tilt range. These values are independent from the frequency band or antenna type and can vary between antennas and bands. EU-RED
Hereby, Kathrein Werke KG declares that the radio equipment is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: http://www.kathrein.com
Our quality assurance system and our environmental management system apply to the entire company and are certified by TÜV according to EN ISO 9001 and EN ISO 14001.
RoHS
Any previous data sheet issues have now become invalid.
Our products are compliant to the EU Directive RoHS as well as to other environmentally relevant regulations (e.g. REACH).
Page 1 of 1 www.kathrein.com KATHREIN-Werke KG · Anton-Kathrein-Straße 1-3 · P.O. Box 10 04 44 · 83004 ROSENHEIM · GERMANY · Phone +49 8031 184-0 · Fax +49 8031 184-820
