Transcript
BRIGHT LED ELECTRONICS CORP. SINCE 1981
BL-HUF35A-AV-TRB
Features: Package Dimensions:
1. Emitted Color : Super Red 2. Lens Appearance : Water Clear. 3. Mono-color type.
2.00+0.05 -0.1
0.15
0.25
1.25±0.1
4. 2.0x1.25x1.0mm(0805) standard package.
CATHODE MARK
6. Compatible with infrared and vapor phase
1.26 1.16
.0 R0
5M
R0 .05 MA X
1.0±0.1
reflow solder process. 7. Compatible with automatic placement
Anode
. AX
.
2°
Cathode Polarity
0.3±0.05
5. Suitable for all SMT assembly methods.
1.4±0.05
equipment.
For reflow soldering CATHODE MARK
8. This product doesnt contain restriction
1.2(.047)
0.9(.035)
1.2(.047)
0.45 0.20
1.00
1.10
0.60
0.45 0.20
Substance, comply ROHS standard.
0.30
0.30
NOTES: 1.All dimensions are in millimeters (inches). 2.Tolerance is ±0.10mm (0.004) unless otherwise specified. 3.Specifications are subject to change without notice.
Applications: 1.
1.25(.049)
Automotive : Dashboards, stop lamps, turn signals.
2.
Backlighting : LCDs, Key pads advertising.
3.
Status indicators : Comsumer & industrial electronics.
4. General use.
Absolute Maximum Ratings(Ta=25 Parameter
)
Symbol
Rating
Unit
Power Dissipation
Pd
52
mW
Forward Current
IF
20
mA
IFP
100
mA
VR
5
V
Peak Forward Current Reverse Voltage
1
Operating Temperature
Topr
-40 ~85
-
Storage Temperature
Tstg
-40 ~85
-
Soldering Temperature
Tsol
See Page6
-
1 Condition for IFP is pulse of 1/10 duty and 0.1msec width.
Ver.1.1 Page 1 of 7 http://www.brtled.com
BRIGHT LED ELECTRONICS CORP. SINCE 1981
BL-HUF35A-AV-TRB
Electrical and optical characteristics(Ta=25 ) Parameter
Symbol
Condition
Min.
Typ.
Max.
Unit
Forward Voltage
Vf
IF=20mA
-
2.2
2.6
V
Luminous Intensity
Iv
IF=20mA
28
94
-
mcd
Reverse Current
IR
VR=5V
-
-
100
µA
645
-
nm
637
nm
Peak Wave Length
p
IF=20mA
-
Dominant Wave Length
d
IF=20mA
627
IF=20mA
-
20
-
nm
IF=20mA
-
120
-
deg
Spectral Line Half-width Viewing Angle
2
1/2
Typical Electro-Optical Characteristics Curves Fig.2 Forward current derating curve Fig.1 Relative intensity vs. wavelength
vs. ambient temperature
1.0
60
Forward current (mA)
Relative radiant intensity
50
0.5
40
30
20
10
0
0 595
645
20
695
60
80
100
Fig.4 Relative luminous intensity vs. ambient temperature
Fig.3 Forward current vs. forward voltage 50
3.0
2.5
30
20
10
(Normalized @20mA)
Relative Luminous intensity
40
Forward current (mA)
40
Ambient temperature Ta( C)
Wavelength (nm)
2.0
1.5
1.0
0.5
0 1
2
3
4
5
0 -40
0
-20
20
40
60
Ambient temperature Ta( C) A
Forward voltage(V)
Fig.6 Radiation diagram
Fig.5 Relative luminous intensity vs. forward current
0
10
20
Relative luminous intensity (@20mA)
2.0 30
1.5 40 1.0 1.0
0.9
50
0.8
60 70
0.5 0.7
80 90 0
10
20
30
40
50
0.5
0.3
0.1
0.2
0.4
0.6
Forward current (mA)
Ver.1.0 Page 2 of 7 http://www.brtled.com
BRIGHT LED ELECTRONICS CORP. SINCE 1981
BL-HUF35A-AV-TRB
Tapping and packaging specifications(Units: mm) USER DIRECTION OF FEED
13.0± 0.5 1.3± 0.1
4.0 ± 0.1
1.75 ± 0.1
CATHODE
1.5± 0.1 4.0 ± 0.1
2.0± 0.05
TRAILER
179± 1
13.0± 0.5
71.0± 1
2.26± 0.1
3.5 ± 0.05
5.3 ± 0.05
END
8.0 ± 0.3
ANODE
1.42 ±0.1 START
LEADER 0.3
FIXING TAPE
NOTE: 3000 pcs PER REEL
Package Method:(unit:mm) Vacuum 12 bag/box 3000 pcs/reel
200
Bar Code Label
245 220
220
Aluminum Foil Bag
185
645
6 box/carton
210 470
Ver.1.0 Page 3 of 7 http://www.brtled.com
BRIGHT LED ELECTRONICS CORP. SINCE 1981
BL-HUF35A-AV-TRB
Bin Limits I n t e n s i t y B i n L i m i ts ( A t 2 0 m A ) BIN CODE Min. (mcd)
Max. (mcd)
M
28
42
N
42
63
P
63
94
Q
94
140
R
140
210
To l e r a n c e f o r e a c h B i n l i m i t i s ± 1 5 %
C o l o r B i n L i m i ts ( A t 2 0 m A ) BIN CODE
Min. (nm)
Max. (nm)
627
637
*
To l e r a n c e f o r e a c h B i n l i m i t i s ±1 n m
V F B i n L i m i ts ( A t 2 0 m A ) BIN CODE
Min.(v)
Max.(v)
B
1.8
2.0
C
2.0
2.2
D
2.2
2.4
E
2.4
2.6
To l e r a n c e f o r e a c h B i n l i m i t i s ±0 . 0 5 V
B IN
x
x
x VF BIN CODE Color BIN CODE Intensity BIN CODE
http://www.brtled.com
Ver.1.0 Page 4 of 7
BRIGHT LED ELECTRONICS CORP. SINCE 1981
BL-HUF35A-AV-TRB
Reliability Test Classification
Test Item
Reference Standard
Operation Life MIL-STD-750D:1026 MIL-STD-883D:1005 JIS-C-7021 :B-1 High Temperature MIL-STD-202F:103B High Humidity JIS-C-7021 :B-11 Endurance Storage Test High MIL-STD-883:1008 Temperature JIS-C-7021 :B-10 Storage Low Temperature JIS-C-7021 :B-11 Storage Temperature MIL-STD-202F:107D Cycling MIL-STD-750D:1051 MIL-STD-883D:1010 JIS-C-7021 :A-2 Thermal Shock MIL-STD-202F:107D Environmental MIL-STD-750D:1051 Test MIL-STD-883D:1011 Solder MIL-STD-202:201A Resistance MIL-STD-750:2031 JIS-C-7021 :A-1
Test Conditions
Connect with a power If=20mA Ta=Under room temperature Test time=1,000hrs Ta=+85 ±5 RH=90%-95% Test time=240hrs
Result
0/20
0/20
High Ta=+100 ±5 Test time=1,000hrs
0/20
Low Ta=-40 ±5 Test time=1,000hrs
0/20
-35 ±5 ~+25 ~+85 ±5 ~+25 30min 5min 30min 5min Test Time=10cycle -40 ±5 ~+85 ±5 20min 20min Test Time=10cycle Preheating 140 -160 ,within 2 minutes. Operation heating 260 (Max.), within 10seconds. (Max.)
0/20
0/20
0/20
Judgment criteria of failure for the reliability Measuring items Forward voltage Reverse current Luminous intensity
Note:
Symbol VF ( V) IR(uA) Iv ( mcd )
Measuring conditions IF=20mA VR=5V IF=20mA
Judgement criteria for failure Initial Level*1.1 Over U*2 Initial Level*0.7
1.U means the upper limit of specified characteristics. 2. Measurment shall be taken between 2 hours and after the test pieces have been returned to normal ambient conditions after completion of each test.
Ver.1.1 Page 5 of 7 http://www.brtled.com
BRIGHT LED ELECTRONICS CORP. SINCE 1981
BL-HUF35A-AV-TRB
Soldering : 1. Manual of Soldering The temperature of the iron tip should not be higher than 300 seconds per solder-land is to be observed.
(572
) and Soldering within 3
2. Reflow Soldering Preheating : 140 ~160 ±5 ,within 2 minutes. Operation heating : 260 (Max.) within 10 seconds.(Max) Gradual Cooling (Avoid quenching).
10 SEC. MAX.
Temperature
260
140~160
MAX. 4
4
/SEC. MAX.
/SEC. MAX.
OVER 2 MIN.
Time DIP soldering (Wave Soldering) : Preheating : 120 ~150 ,within 120~180 sec. Operation heating : 245 5 within 5 sec.260 Gradual Cooling (Avoid quenching).
(Max)
Temperature
Soldering heat Max. 260 245
120~150
within 5 sec.
Preheat 120~180 sec.
Time Handling : Care must be taken not to cause to the epoxy resin portion of BRIGHT LEDs while it is exposed to high temperature. Care must be taken not rub the epoxy resin portion of BRIGHT LEDs with hard or sharp article such as the sand blast and the metal hook.
Ver.1.1 Page 6 of 7 http://www.brtled.com
BRIGHT LED ELECTRONICS CORP. SINCE 1981
BL-HUF35A-AV-TRB
Notes for designing: Care must be taken to provide the current limiting resistor in the circuit so as to drive the BRIGHT LEDs within the rated figures. Also, caution should be taken not to overload BRIGHT LEDs with instantaneous voltage at the turning ON and OFF of the circuit. When using the pulse drive care must be taken to keep the average current within the rated figures. Also, the circuit should be designed so as be subjected to reverse voltage when turning off the BRIGHT LEDs.
Storage: In order to avoid the absorption of moisture, it is recommended to solder BRIGHT LEDs as soon as possible after unpacking the sealed envelope. If the envelope is still packed, to store it in the environment as following: (1) Temperature : 5 -30 (41 )Humidity : RH 60 Max. (2) After this bag is opened, devices that will be applied to infrared reflow, vapor-phase reflow, or equivalent soldering process must be: a. Completed within 168 hours. b. Stored at less than 30% RH. (3) Devices require baking before mounting, if: (2) a or (2) b is not met. (4) If baking is required, devices must be baked under below conditions: 48 hours at 60 ±3 .
Package and Label of Products: (1) Package: Products are packed in one bag of 3000 pcs (one taping reel) and a label is attached on each bag. (2) Label:
BRIGHT LED LOGO
B
Part No. Quantity BIN. Sealing Date x
xx xx Year Month
xx Day
Manufacture Location
Ver.1.0 Page 7 of 7 http://www.brtled.com
