Datasheet For Igd-1-424-p1n4-dl

Transcript

IGD-1-424-P1N4-DL-FA A COMPLETER Absolute maximun ratings Symbol Conditions IOUT MAX Maximum continuous output current VOUT MAX Maximum output voltage VBUS MAX Maximum DC Bus voltage in operation FOUT Inverter Output frequency FSW Maximum switching frequency T AMBIENT = T AIR COOLING = 40°C unless otherwise specified Electrical characteristics Symbol Conditions T AMBIENT = T AIR COOLING = 40°C unless otherwise specified min typ max Unit Unit ARMS VAC VDC Hz kHz Values 200 500 900 500 25 AC phase IGBT Module stack SEMIKUBE - Size T0.5 3-phase inverter Ordering No. 08800445 Description IGD-1-424-P1N4-DL-FA Option 0C 0N 0P K - 0X - 1F2 Features 1 1 1 1 1 1 Designed in regards to EN50178 recommandations RoHS compliant Fast mounting and dismounting Very high life-time expectancy Integrated voltage, current and temperature sensors Air cooled power stacks IOUT RATED VOUT POUT FSW FOUT DC Bus Rated output current Output voltage Rated output power Inverter switching frequency Output frequency VBUS Efficiency Rated DC voltage VBUS=750VDC, No overload, Tj<150°C, Power factor PF = 1, Cabinet airflow in operation at 400m3/h Fan airflow through heatsink at 900 m3/h 200 400 140 3 50 ARMS VAC kW kHz Hz 750 VDC Total power losses PLOSS INV Inverter efficiency η Filtering characteristics VBUS Rated DC voltage applied to the caps bank without switching VDC CAPACITOR Max DC voltage applied to the caps bank (max 30% of LTE) without switching τd5% Discharge time of the capacitors (5%) CDC Capacitor bank capacity LTE Calculated LTE of the caps with forced air cooling Stack Insulation VISOL Frame / Power stage AC/DC (insulation test voltage DC, 60s) 1 915 >98 W % 1 100 VDC 1 100 VDC 1,68 > 100 s mF kH 3 200 V 285 1,43 Typical Applications 1 Industrial applications 1 Solar Inverters Footnotes 1) the user shall ensure that the ambiant air shall be ventilated in order not to create temperature hot spots. REMARKS This technical information specifies semiconductor devices but promises no characteristics. No warranty or guarantee, expressed or implied is made regarding delivery, performance or suitability. B6CI © by SEMIKRON Rev. 3 - 31.08.2012 1 IGD-1-424-P1N4-DL-FA Environmental conditions Characteristics Conditions min typ max Unit -25 55 °C 5 85 % 1 000 IP00 2 m - 25 kg 230 300 VAC W Climatic Ambient temperature 1) IEC 60721-3-3, class 3K3 extended In operation Humidity IEC 60721-3-3, class 3K3 no condensation no icing Mechanical IGBT Module stack Installation altitude Protection index Pollution degree without derating IEC 60529 EN 50178 Weight total 3-phase inverter including heatsink fan Thermal data VSUPPLY PFAN Heatsink fan AC voltage supply at 50Hz Rated power at VSUPPLY SEMIKUBE - Size T0.5 3-phase inverter Gate Driver Characteristcs Symbol Conditions Ordering No. 08800445 Description IGD-1-424-P1N4-DL-FA Option 0C 0N 0P K - 0X - 1F2 Features 1 1 1 1 1 1 Designed in regards to EN50178 recommandations RoHS compliant Fast mounting and dismounting Very high life-time expectancy Integrated voltage, current and temperature sensors Air cooled power stacks Typical Applications 1 Industrial applications 1 Solar Inverters Footnotes 1) the user shall ensure that the ambiant air shall be ventilated in order not to create temperature hot spots. REMARKS Gate Driver / controler data VS supply voltage ISO Supply primary current No load Max. Supply primary current ViT+ input threshold voltage HIGH ViTinput threshold voltage LOW RIN Input resistance CIN Input capacitance Measurement & protection Scaling Accuracy of analogue signal @ Ta=25°C DC link voltage Temperature coefficient sensing UDC analogue OUT max. load current Max. voltage range Max measurable DC Link Voltage Scaling Current sensing Accuracy of analogue signal Ianalogue OUT Temperature coefficient Max. output current per phase Max. voltage range ITRIPSC Over current trip level Scaling Temperature Minimum measurable temperature sensing Tanalogue OUT Max. output current Max. voltage range Ttp Over temperature protection Threshold level for reset after failure event Tth T AMBIENT =25°C unless otherwise specified min typ max Unit 21,6 360 24 26,4 1 500 0.7 x VS 0.3 x VS 17 1 10 -2 +2 0,03 5 15 1 200 24 -4 +4 0,07 5 15 450 10 25 95 70 100 5 15 105 VDC mA mA VDC VDC kΩ nF mV.V-1 % %.K-1 mA VDC VDC mV.A-1 % %.K-1 mA VDC APEAK mV.°C-1 °C mA VDC °C °C This technical information specifies semiconductor devices but promises no characteristics. No warranty or guarantee, expressed or implied is made regarding delivery, performance or suitability. B6CI © by SEMIKRON Rev. 3 - 31.08.2012 2 IGD-1-424-P1N4-DL-FA Electrical connection 8FB3E579A5E9"D#8F9$2""7%9CDEE8C43DE Driver connector type 123456789A8B5789CDEE8C4DF 5E2A5C42F8F  5F49E2B68F 99 9!9 © by SEMIKRON Rev. 3 - 31.08.2012 3 IGD-1-424-P1N4-DL-FA Driver X1 connector assignment PIN 1,3,5 VS IN 2,4,6 GND Specification Supply voltage 7 [Reserved] [dominant/recessive] 8 GND (Signal Status) Ground for Signal Status OUT 9 Signal Status BIDIRECTIONAL 24VDC digital logic input, push pull LOW [dominant] = "Not ready to operate" HIGH [recessive] = "Ready to operate" 10 [Reserved] [dominant/recessive] 11 Temperature Analogue OUT Nominal voltage range: 0…10V 12 GND (Temperature Analogue) Ground for Temperature Analogue OUT 13 UDC Analogue OUT Nominal voltage range: 0…10V 14 GND (UDC Analogue) Ground for UDC Analogue OUT 15 TOP phase U Switching Signal IN 16 BOT Phase U Switching Signal IN 17 [Reserved] [dominant/recessive] 18 GND (TOP phase U, BOT phase U) Ground for TOP & BOT phase U IN 19 I phase U Analogue OUT Nominal voltage range: 0…10V 20 GND (I Analogue phase U) Ground for I phase U Analogue OUT 21 TOP phase V Switching Signal IN 22 BOT Phase V Switching Signal IN 23 [Reserved] [dominant/recessive] 24 GND (TOP phase V, BOT phase V) Ground for TOP & BOT phase V IN 25 I phase V Analogue OUT Nominal voltage range: 0…10V 26 GND (I Analogue phase V) Ground for I phase V Analogue OUT 27 TOP phase W Switching Signal IN 28 BOT phase W Switching Signal IN 29 [Reserved] [dominant/recessive] 30 GND (TOP phase W, BOT phase W) Ground for TOP & BOT phase W IN 31 I phase W Analogue OUT Nominal voltage range: 0…10V 32 GND (I Analogue phase W) Ground for I phase W Analogue OUT 33,34 © by SEMIKRON Signal 24VDC digital logic input, push pull LOW = "Switch off" HIGH = "Switch on" 24VDC digital logic input, push pull LOW = "Switch off" HIGH = "Switch on" 24VDC digital logic input, push pull LOW = "Switch off" HIGH = "Switch on" 24VDC digital logic input, push pull LOW = "Switch off" HIGH = "Switch on" 24VDC digital logic input, push pull LOW = "Switch off" HIGH = "Switch on" 24VDC digital logic input, push pull LOW = "Switch off" HIGH = "Switch on" [Reserved] Rev. 3 - 31.08.2012 4 IGD-1-424-P1N4-DL-FA Dimensions This technical information specifies semiconductor devices but promises no characteristics. No warranty or guarantee expressed or implied is made regarding delivery, performance or suitability. © by SEMIKRON Rev. 3 - 31.08.2012 5 250 [ARMS] [ARMS] IGD-1-424-P1N4-DL-FA 200 250 IOUT IOUT 200 150 150 100 100 Cooling air temperature 30°C 50 50 40°C SOA 50°C 0 0 0 5 10 15 20 25 fsw [kHz] 0 200 600 800 VBUS 1000 [VDC] 123456789AB8C4DE66B8C Safe Operating Area [ARMS] Max. Output current vs. Switching frequency [ARMS] 400 200 250 IOUT IOUT 200 150 150 100 100 Switching frequency Fsw = 3kHz Fsw = 5kHz 50 Cooling air temperature 50 Fsw = 7kHz 40°C Fsw = 9kHz 50°C Fsw = 12kHz 55°C 0 25 30 35 40 45 50 55 60 Tair cooling [ C] 0 65 300 400 500 600 700 800 VBUS This curve does not consider the SEMIKUBE ambient temperature 900 [VDC] Switching frequency at 7 kHz Max. Output current vs. Ambient temperature Max. Output current vs. DC bus voltage [ KW-1] Zth heatsink to ambient 0,025 0,02 0,015 0,01 0,005 0 1 10 100 Time [s] 1000 heatsink Poly. (heatsink) Thermal characteristics © by SEMIKRON Rev. 3 - 31.08.2012 6