Transcript
IL series
New! Sealedpushbuttonswitchesforthickpanels-longbushingØ12mm-momentary Distinctive features and specifications
❑Momentary pushbuttons for thick panels ❑Illuminated or non-illuminated ❑Tactile feedback ❑Flat round actuator for optional marking ❑Sealed to IP67 (standard models only) B1 ENVIRONMENTAL SPECIFICATIONS
GENERAL SPECIFICATIONS
• Front panel sealing according to IEC 60529 : IP67 (standard models) IP54 (options X1242 and 234) • Shock resistance : 100 g according to IEC 512-4, test 6c • Vibration resistance : 10-500 Hz - 10 g according to IEC 512-4, test 6d • Salt spray : IEC 512-6, test 11f • Operating temperature : -40°C to +85°C ELECTRICAL SPECIFICATIONS
• Max. current/voltage rating with resistive load : 2A 24VDC, 200.000 cycles • Initial contact resistance : 50 mΩ max. • Insulation resistance : 1 GΩ min. at 500VDC • Dielectric strength : 1.000 Vrms
• Panel thickness : 1,50 mm (.059) min. 10 mm (.393) max. • Total travel : 1,7 mm (.067) +/- 0,3 mm • Typical operating force : 4N +/- 2N • Low level or mechanical life : 1.000.000 cycles • Torque : 1 Nm max. applied to nut • Soldering : 300°C max. for 3 seconds MATERIALS
LED COMPONENT SPECIFICATIONS
LED colour
Forward current
Typ. forward voltage Max. forward voltage
Super red (L0S)
20mA
2,1V
2,3V
Yellow (L0Y)
20mA
2,1V
2,3V
Green (L0G)
20mA
2,1V
2,3V
Blue (L0B)
20mA
3,2V
3,8V
White (L0W)
20mA
3,35V
4,25V
• Case : thermoplastic UL94-V0 • Actuator : polyamide 6/6 • Bushing/bezel : polyamide 6/6 • Contacts : silver, gold plated • Terminal seal : epoxy
A resistor must be series-connected by the user. Resistor value = supply voltage - LED forward voltage LED forward current
Matrix mounting
12.90 (.507)
1
20.00 (.787)
Back of panel space requirement
20.00 (.787)
20.00 (.787)
1.50min-10.00Max (.059MIN.-.393MAX.)
Panel cut-out
- STANDARD BEZEL
16.40 (.645)
MOUNTING
Ø13.60 (.535DIA) Ø13.50 (.531DIA)
➀ Flat seal Mounting for reduced bezel : see options X1242 and 234 at the end of the series.
B1-6
www.apem.com
APEM
IL series New! Sealedpushbuttonswitchesforthickpanels-longbushingØ12mm-momentary Overview IL
Electrical function
Actuator shape
SERIES
R P
Round, curved Round, flat
3
Normally open (NO)
Terminals F P S
Flying leads Straight PC Solder lugs
Contacts AD Silver, gold plated
B1 Actuator colour 1 2 3 4 5 6 7/1 8 9 B
Blue Black Green Grey Yellow Red White Bright chrome Orange Dark blue
Blank L0S L0Y L0G L0B L0W
LED colour
Options
Non-illum. Super red Yellow Green Blue White
X1242 Reduced bezel, frontal mounting 234 Reduced bezel, standard mounting
hes: switc s. m o t s e e seri act cu Compe end of th se
ABOUT THIS SERIES On the following pages, you will find successively : - model structure of switches and options in the same order as in above chart Dimensions : first dimensions are in mm while inches are shown as bracketed numbers.
NOTICE : please note that not all combinations of above numbers are available. Refer to the following pages for further information.
Mounting accessories : Standard hardware supplied : 1 flat seal and 1 hex nut 14 mm (.551) across flats. Hex nut part number U166. Packaging unit : 25 pieces
APEM
www.apem.com
B1-7
IL series
New! Sealedpushbuttonswitchesforthickpanels-longbushingØ12mm-momentary Illuminated • Curved or flat actuator • Antirotation bushing
4.55 (.179)
5.20 (.204)
Straight P
1.00 (.039)
MODEL STRUCTURE
B1
Actuator marking available on ILP models (symbol 10 mm max.). On request.
➞ Flat
10.80 (.425)
EPOXY 1.20 (.047)
5.20 (.204)
Normally open
Ø12.00x0.75SI (.472DIAx0.75IS)
6.10 (.240)
Flat actuator ILP3SAD
Ø17.50 (.688DIA)
1.50 (.059)
Normally open 19.30 (.759)
Curved actuator ILR3SAD
Ø12.00 (.472DIA)
2.00 (.078)
5.00 (.196)
Solder lug terminals
0.40 (.015)
2.00 (.078)
5.08 (.200)
Also available with straight PC terminals : IL•3PAD
5.00 (.196)
Flat actuator ILP3FAD
Normally open
27.00 Max. (1.063 MAX.)
Normally open
Ø12.00x0.75SI (.472DIAx0.75IS)
Ø12.00 (.472DIA) Ø17.50 (.688DIA)
10.80 (.425)
Ø9.50 (.374DIA)
500±10 19.68±.393)
Curved actuator ILR3FAD
2.00 (.078)
➞ Flat
Flying lead terminals
ACTUATOR COLOUR
1 : blue - 2 : black - 3 : green - 4 : grey - 5 : yellow - 6 : red - 7/1 : white - 8 : bright chrome 9 : orange - B : dark blue
LED COLOUR
L0S : red - L0Y : yellow - L0G : green - L0B : blue - L0W : white
B1-8
www.apem.com
APEM
IL series New! Sealedpushbuttonswitchesforthickpanels-longbushingØ12mm-momentary Non-illuminated • Curved or flat actuator • Antirotation bushing
4.55 (.179)
5.20 (.204)
Straight P
1.00 (.039)
MODEL STRUCTURE Actuator marking available on ILP models (symbol 10 mm max.). On request.
Normally open
Ø17.50 (.688DIA)
10.80 (.425)
Ø12.00x0.75SI (.472DIAx0.75IS)
1.20 (.047)
EPOXY 5.20 (.204)
Flat actuator ILP3SAD
Ø12.00 (.472DIA)
2.00 (.078)
5.00 (.196)
Normally open 18.40 (.724)
Curved actuator ILR3SAD
1.50 (.059)
➞
Solder lug terminals
Flat
0.40 (.015)
2.00 (.078)
5.08 (.200)
Also available with straight PC terminals : IL•3PAD
5.00 (.196)
Flat actuator ILP3FAD
Normally open
21.00 Max. (.826 MAX.)
Normally open
Ø12.00x0.75SI (.472DIAx0.75IS)
Ø12.00 (.472DIA) Ø17.50 (.688DIA)
10.80 (.425)
Ø9.50 (.374DIA) 500±10 19.68±.393)
Curved actuator ILR3FAD
2.00 (.078)
➞ Flat
Flying lead terminals
ACTUATOR COLOUR
1 : blue - 2 : black - 3 : green - 4 : grey - 5 : yellow - 6 : red - 7/1 : white - 8 : bright chrome 9 : orange - B : dark blue
APEM
www.apem.com
B1-9
B1
IL series
New! Sealedpushbuttonswitchesforthickpanels-longbushingØ12mm-momentary Custom switches Reduced bezel for compact matrix mounting - option X1242 • Dia. 15 (.590) reduced bezel • Mounting from the front into a threaded panel cut-out • Matrix mounting : 16 x 16 mm (.630x.630) • Illuminated or non-illuminated • Same terminal options and colours as standard models • Part numbers on request. ILP3FAD...X1242
B1 Reduced bezel for compact matrix mounting - option 234 • Dia. 15 (.590) reduced bezel • Standard panel mounting • Matrix mounting : 17,5 x 17,5 mm (.689x.689) • Illuminated or non-illuminated • Same terminal options and colours as standard models • Part numbers on request. ILP3SAD...234
MOUNTING
2
17.50 (.689)
17.50 (.689)
17.50 (.689)
12.90 (.507)
1.50min-10.00Max (.059MIN.-.393MAX.)
Matrix mounting 0.80min-4.30Max (.031MIN.-.169MAX.)
Panel cut-out
- REDUCED MODEL
Ø13.60 (.535DIA)
➁ O-ring
B1-10
Ø15.60 (.614DIA)
Ø13.50 (.531DIA)
www.apem.com
APEM
