Transcript
Z109REG2 High performance universal converter Z109REG2 is an advanced universal converter able to manage all analog signals (mA, V, PT100, Pt1000, Pt500, Ni100, TCs, Ohm) and convert / isolate it into mA/V standard signals. The device can be configured through dip-switches, PC software or handheld device. A digital contact is available as ALARM or STROBE (multiplexing). It can be requested with low or high power supply. A 3-way galvanic isolation among Power supply // input // output circuits assures the integrity of your datas. Vac / dc Power Supply 1
Input
Ouput 1
V
V
Technical Specifications Electrical Specifications
Output
Power supply
10..40 Vdc / 19..28 Vac / 50-60 Hz
Channel Numbers
Power consumption
2,5 W
Voltage
Isolation
1.500 Vac (3 way)
Power transducers
Yes
Current
Status Indicators
Power supply, error, data transmission, data reception, input status
Relay
Protection Degree
IP20
Standard
Thermomechanical Specifications Operating -10..+60 °C Temperature Dimension (W x H x D) 17.5 x 100 x 112 mm Accuracy
0,1%
Response time
35 ms (11 bit)..140 ms (16 bit) Dip- switches EASY_Z109 (PC software) Test-3 (hand held calibrator) 35 mm DIN rail guide
Setting Mounting
Input Channel Numbers
Potentiometer
1 (mV, V) Bipolar from 75 mV to 20 V Resolution 15 bit + sign Bipolar up to 20 mA Resolution 1 μA Pt100, Pt500, Pt1000, Ni100, KTY81,KTY84, NTC Measure 3, 4 wires Range: -200..600 °C Resolution 0,1°C Type J, K, R, S, T, E, B, N Resolution 2,5 μV 500 Ω ..100 kΩ
Rheostat
500 Ω..25 kΩ
Strobe
Alternative to the relay output
Voltage Current Rtd Thermocouple
1 4 scales: 0..1, 0..5, 0..10, 2..10 V Min load resistance: 2.000 Ω 2 scales: 0/4..20 mA (active/passive) Max load resistance: 600 Ω Alternative to the strobe NC / NA in case of alarm
Approval
CE, UL-CSA EN 50081-2; EN 55011; EN 50082-2; EN 61000-2-2/4; EN 50140/141; EN 61010-1
Norms
order codes Code
Description
Z109REG2 Z109REG2-H
High performance universal converter, Power supply 10..40 Vdc / 19..28 Vac High performance universal converter, Power supply 85..265 Vac/Vdc
accessories & software
PM001601 Programming cable
TEST-3 Handheld configurator
EASY SETUP Programming software
www.seneca.it
analog universal input
high class accuracy
fast response time
wide operating temperature
mA, V, Ohm, RTD, TC
0,1%
35 ms (11 bit + segno)
-20..+60°C
transducer power supply
high resolution
auxiliary contacts
Approvals
16 bit
Strobe Input SPDT relay Output
20 Vcd, 20 mA
G2
Z109RE
1 2 3 4 5 6
1 2 3 4 5 6
1 2 3 4 5 6
Z109REG2 Z109REG2 Z109REG2 7 8 9 10 11 12
7 8 9 10 11 12
7 8 9 10 11 12
APPLICATION NOTE Multiplexer strobe
Trip amplifier
2
Z109REG
G2
9..40 Vdc 19..28 Vac
Z109RE
1 2 3 4 5 6 POWER ERROR
1 2 3 4 5 6 POWER ERROR
1 2 3 4 5 6 POWER ERROR COM
COM
COM
Z109REG2 7 8 9 10 11 12
EG2 Z109R 1 2 3 6
74 85 9 10 11 12
EG2 Z109R 1 2 3 47 58 69
1 2 3 4 5 6
10 11 12
Pt100 Z109REG2 Z109REG2
Z109REG2 7 8 9 10 11 12
7 8 9 10 11 12
7 8 9 10 11 12
1 2 3 4 5 6 POWER
+25 °C
ERROR COM
Z109REG2 7 8 9 10 11 12
4...20
Signal retransmission 1
мА
Signal retransmission 2
Pt100
Pt100 Pt100 1 2 3 4 5 6
3 1 2 31 2 6 4 5 64 5 POWER
24 V
ERROR
POWER ERROR
POWER ERROR COM
COM
C 5 °5C° +2+2
COM
Z109REG2 7 8 9 10 11 12
Z109REG2
Z109REG27
24 V
8 9
11 12 7 8 910 10 11 12
4...20
4...2 4...20 0 мА мА
мА
Configuration • Input type • Zero and Span • Output type • Scale inversion
2- HANDHELD Pt100
Pt100
• Min / max range scale; digital filter; square root extraction • Fault sensor • Analog scale; error analog output value • Rejection frequency (50 – 60 Hz) 4...20 • Sampling time / Resolution мА • Measure 2, 3, 4 wires for RTD 4...20 alarm control, strobe • Relay мА configuration 1 2 3 4 5 6 POWER ERROR
1 2 3 4 5 6
COM
POWER
Z109REG2
ERROR
7 8 9 10 11 12
COM
Z109REG2 7 8 9 10 11 12
3 - SOFTWARE
• Min / max range scale; digital filter; square root extraction • Fault sensor • Analog scale; error analog output value • Rejection frequency (50 – 60 Hz) • Sampling time / Resolution • Measure 2, 3, 4 wires for RTD • Relay alarm control, strobe configuration
via Germania, 34 • 35127 Padova - (I) - Tel. +39 049 87.05.359 (.408) Fax +39 049 87.06.287 • www.seneca.it •
[email protected] The material in this document is for information only and is subject to change without notice. While reasonable efforts have been made in the preparation of this document to assure its accuracy, SENECA assumes no liability resulting from errors or omissions, or from the use of the information contained herein.
Publication Z109REG2 – March 2013
1- DIP-SWITCHES
