Transcript
Train Antenna 380 – 430 MHz and GPS 1575 MHz 87010005 • Two-band antenna: 380 – 430 MHz and GPS. • The antenna can be operated in both frequency ranges simultaneously. • Low profile antenna in fiberglass radome. • The antenna fulfils the requirements according to EN 50155.
On a conductive surface with a minimum size of 1000 x 1000 mm using 4 M10 bolts.
Grounding and high voltage protection:
This antenna, tested by an independent institute and approved by the “Deutsche Bahn AG”, is DC grounded to protect against lightning and high-tension lines.
Accessories:
Low noise amplifier GPS 86010142 (please order separately).
Warning:
If the antenna is operated without the preamplifier type no. 86010142, please note the following points. – Due to the fact that the inner conductor of the antenna GPS is DC grounded, the input of the GPS receiver is loaded with a DC short circuit. If the GPS receiver provides a remote DC power supply, this could damage the GPS receiver. – At the input of the antenna GPS a level of –25 dB below the signal applied at the input of the antenna 380 – 430 MHz appears. Depending on the level of the signal applied at the input of the antenna 380 – 430 MHz, the GPS receiver may be overloaded or damaged.
85 56 contact area
seal
32
82
142
Input Antenna GPS Input Antenna 400 MHz
11 mm diameter
Radiator: Copper and brass. Flange: Aluminum. Radome: Fiberglass. All screws and nuts: Stainless steel. Colour: Grey. Sealing: Neoprene and silicon. Note: Don’t use detergents that might harm the sealing.
Mounting:
936.2961/d
Subject to alteration.
Material:
Mounting flange:
contact area
Mounting hole for the connector: 33 (max. 35) mm diameter. Note: Keep mounting surface clear of paint for electrical contact. Evenness of opposite surface 0.2 mm. Use a cap nut or hex-head screw plus the enclosed sealing washer.
Hex-head screw M10 torque 15 Nm – 20 Nm Added sealing washer
Cap nut M10 DIN 1587 torque 15 Nm – 20 Nm 15
Impedance Inner conductor Radome weight Total weight Packing size Height
Cable RG 316/U of 225 mm length with TNC male connector 1575.42 ±1 MHz < 1.5 Right hand circular 2 dB (ref. to the circularly polarized isotropic antenna) 50 Ω DC grounded 186 g Approx. 500 g 150 x 90 x 190 mm 150 mm
115
Frequency range VSWR Polarization Gain (90° elevation)
N female 380 – 430 MHz < 1.7 0 dB (ref. to the quarter-wave antenna) 50 Ω Vertical 100 W (at 50° C ambient temperature) DC grounded
43
Antenna 380 – 430 MHz Input Frequency range VSWR Gain Impedance Polarization Max. power Inner conductor Antenna GPS Input
87010005
145
Type No.
Situation of mounting
www.kathrein.de
87010005 Page 1 of 2
KATHREIN-Werke KG · Anton-Kathrein-Straße 1-3 · P.O. Box 10 04 44 · 83004 ROSENHEIM · GERMANY · Phone +49 8031 184-0 · Fax +49 8031 184-820
Train Antenna 380 – 430 MHz and GPS 1575 MHz 87010005
UL94 (HB) DIN 5510 T2 DIN EN 45545-2: 2013
IP class:
IP 66 (when product is mounted properly)
Standards:
EN 50122-1 EN 50125 EN 50155 EN 60068-2-1 EN 60068-2-2 EN 60068-2-6 EN 60068-2-27 EN 60068-2-30 EN 61373 ETS 300 019-1-2 class 2.2 ETS 300 019-1-1 T 1.2 ETS 300 019-1-5 T 5.2 ETS 300 019-2-2 T 2.2 ETS 300 019-1-2 T 1.2
936.2961/d
Subject to alteration.
Fire prevention:
Page 2 of 2 87010005
Any previous data sheet issues have now become invalid.
www.kathrein.de
KATHREIN-Werke KG · Anton-Kathrein-Straße 1-3 · P.O. Box 10 04 44 · 83004 ROSENHEIM · GERMANY · Phone +49 8031 184-0 · Fax +49 8031 184-820
General Information about Panel Antennas Environmental conditions:
Kathrein cellular antennas are designed to operate under the environmental conditions as described in ETS 300 019-1-4 class 4.1 E. The antennas exceed this standard with regard to the following items: – Low temperature: –55 °C – High temperature (dry): +60 °C For antennas equipped with FlexRET: The electrical downtilt adjusting is designed to operate under the environmental conditions as described in the valid data sheet of the FlexRET. Ice protection: Due to the very sturdy antenna construction and the protection of the radiating system by the radome, the antenna remains operational even under icy conditions.
Environmental tests:
Kathrein antennas fulfil the stated specifications after completion of the environmental tests as defined in ETS 300 019-2-4. The homogenous d esign of Kathrein’s antenna families uses identical modules and materials. Extensive tests have been performed on typical samples and modules. The vibration test has been adapted relating to frequency and acceleration to the conditions of mast mounted antennas.
Please note:
As a result of more stringent legal regulations and judgements regarding product liability, we are obliged to point out certain risks that may arise when products are used under extraordinary operating conditions. The mechanical design is based on the environmental conditions as stipulated in ETS 300 019-1-4. Wind loads are calculated according to DIN 1055-4. The antennas may be used at locations where the anticipated peak wind velocity or gust wind speed lies within the maximum wind speed listed in the data sheet. We warrant the mechanical safety and electrical functionality under such conditions. The wind speeds are defined in accordance with the DIN, EN or TIA standards. This warranty makes allowance for the partial safety factors specified in those standards. Extraordinary operating conditions, such as heavy icing or exceptional d ynamic stress (e.g. strain caused by oscillating support structures), may result in the b reakage of an antenna or even cause it to fall to the ground. These facts must be c onsidered during the site planning process.
936.4694/d
Subject to alteration.
The details given in our data sheets have to be f ollowed carefully when installing the antennas and a ccessories. Site planning and installation must be carried out by qualified and experienced staff. All relevant national safety regulations must be upheld and respected. Incorrect site planning, faulty installation, as well as interfering surroundings on site, may lead to deviations in the electrical parameters compared to those specified in the respective data sheets. The connectors on this product are only suitable for connecting to the compatible counterpart. Please ensure that the connected cable has been fitted with a connector of the same standard, otherwise damage may occur. The tilt values will be set to any arbitrary value in the given tilt range. These values are independent from the frequency band or antenna type and can vary between antennas and bands. EU-RED
Hereby, Kathrein Werke KG declares that the radio equipment is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: http://www.kathrein.com
Our quality assurance system and our environmental management system apply to the entire company and are certified by TÜV according to EN ISO 9001 and EN ISO 14001.
RoHS
Any previous data sheet issues have now become invalid.
Our products are compliant to the EU Directive RoHS as well as to other environmentally relevant regulations (e.g. REACH).
Page 1 of 1 www.kathrein.com KATHREIN-Werke KG · Anton-Kathrein-Straße 1-3 · P.O. Box 10 04 44 · 83004 ROSENHEIM · GERMANY · Phone +49 8031 184-0 · Fax +49 8031 184-820
