Transcript
Multi-band Panel
R1
B1
Frequency Range
698 – 894
1710 – 2170
Dual Polarization
X
X
65°
65°
iRCU
iRCU
0°–10°
0°–10°
Half-power Beam Width Integrated replaceable Remote Control Unit Adjustable Electrical Downtilt
XXPol Panel iRCU 698–894/1710–2170 65°/65° 16/18.5dBi 0°–10°/0°–10°T
80010765V01
Type No. A) Antenna specifications
1710 – 2170 1710 – 1755 MHz 1850 – 1990 MHz 2110 – 2170 MHz +45°, –45° +45°, –45° 18 dBi 18.5 dBi
+45°, –45° +45°, –45° 13.15 dBd / 15.3 dBi 13.65 dBd / 15.8 dBi 68° Copolar: > 30 dB Average: 34 dB
65° Copolar: > 30 dB Average: 34 dB
Cross polar ratio Maindirection 0° Typically: > 25 dB Typically: > 20 dB Sector ±60° > 10 dB, Avg. 16 dB > 10 dB, Avg. 14 dB Tracking, Avg. 1.0 dB 1.5 dB Squint ±2.5° ±3.0° Vertical Pattern: Half-power beam width 11.8° 10.8° Electrical tilt 0°– 10°, continuously adjustable Min. sidelobe suppression for 0° ... 5° ... 10° T 0° ... 5° ... 10° T first sidelobe above main beam: 16 ... 16 ... 18 dB 18 ... 18 ... 16 dB Average: 18 ... 20 ... 20 dB 20 ... 22 ... 20 dB Impedance VSWR Isolation, between ports Intermodulation IM3 Max. power per input
63° Copolar: > 27 dB Average: 34 dB
62° Copolar: > 27 dB Average: 34 dB
Typically: > 25 dB > 8 dB, Avg. 15 dB 1.5 dB ±3.0°
Typically: > 30 dB > 10 dB, Avg. 15 dB 1.0 dB ±2.5°
5.8° 5.8° 0°– 10°, continuously adjustable 0° ... 5° ... 10° T 0° ... 5° ... 10° T 18 ... 18 ... 18 dB 18 ... 18 ... 18 dB 20 ... 22 ... 20 dB 20 ... 22 ... 20 dB
50 Ω < 1.5 Intrasystem: > 30 dB, Intersystem: > 35 dB < –150 dBc (2 x 43 dBm carrier) 500 W (at 50 °C ambient temperature) 300 W (at 50 °C ambient temperature)
Field replaceable without dismantling the antenna Logical interface ex factory1) 3GPP/AISG 2.0 Protocols Compliant to AISG 1.1 and 3GPP/AISG 2.0 2 x 8pin connector acc. IEC 60130-9; Hardware interface2) according to AISG: – iRCU in (male): Control / Daisy chain in – iRCU out (female): Daisy chain out Power supply 10 ... 30 V Power consumption < 1 W (stand by) < 8.5 W (motor activated) Adjustment time (full range) 40 sec. Adjustement cycles > 50,000 3) Certification CE, * See mounting instructions and warnings. 1)
The protocol of the logical interface can be switched from 3GPP/AISG 2.0 to AISG 1.1 and vice versa with a vendor specific command. Start-up operation of the iRCU 86010149 is possible in a RET system supporting AISG 1.1 or supporting 3GPP/AISG 2.0 after performing a layer 2 reset before address assignment. The protocol can also be changed as follows: AISG 1.1 to 3GPP: Enter „3GPP“ into the additional data filed „Installer’s ID“ and perform a layer 7 reset or a power reset. 3GPP to AISG 1.1: Enter „AISG 1“ into the additional data field „Installer’s ID“ and perform a layer 2 reset or a power reset. After switching the protocol any other information can be entered into the „Installer’s ID“ field.
iRCU out in 698–894 –45°
iRCU 698–894 +45°
7-16 long neck7-16 8pin male 8pin female
in out
1710 –2170 1710 –2170 –45° +45° 7-16 long neck7-16 8pin female 8pin male
698 – 894 MHz: +45°/–45° Polarization 66$ 11.3$
10
10
3
3
Horizontal Pattern
Vertical Pattern 0°– 10° electrical downtilt
1710 – 2170 MHz: +45°/–45° Polarization 63$
5.8°
The tightning torque for fixing the connector must be 0.5 – 1.0 Nm (‘hand-tightened’). The connector should be tightened by hand only!
3)
Tested to comply with FCC Standards. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
www.kathrein.de
10
10
3
Horizontal Pattern
3
dB
2)
dB
936.4267/a
Subject to alteration.
B) iRCU specifications (86010149)*
dB
Polarization Gain Horizontal Pattern: Half-power beam width Front-to-back ratio
B1, connector 3 – 4
698 – 894 698 – 806 MHz 824 – 894 MHz
dB
Frequency range
R1, connector 1– 2
Vertical Pattern 0°– 10° electrical downtilt 80010765V01 Page 1 of 2
KATHREIN-Werke KG · Anton-Kathrein-Straße 1 – 3 · P.O. Box 10 04 44 · 83004 Rosenheim · Germany · Phone +49 8031 184-0 · Fax +49 8031 184-973
Accessories General Information
4 x 7-16 female (long neck) iRCU in: 2 x 8pin male iRCU out: 2 x 8pin female Bottom Frontal: 950 N (at 150 km/h) 2380 N (at 150 mph) Lateral: 360 N (at 150 km/h) 890 N (at 150 mph) Rearside: 980 N (at 150 km/h) 2460 N (at 150 mph) 241 km/h (150 mph) 1918 / 300 / 152 mm (75.5 / 11.8 / 6.0 inches) H (Heavy) 23.5 kg (51.8 lbs) / 25.5 kg (56.2 lbs) (clamps incl.) 2166 x 322 x 190 mm (85.3 x 12.7 x 7.5 inches) Panel and 2 units of clamps 42 – 115 mm diameter
Connector position Wind load
Max. wind velocity Height/width/depth Category of mounting hardware Weight Packing size Scope of supply Material:
Reflector screen: Aluminum. Radiator: Tin-plated zinc. iRCU housing: Coated aluminum. Fiberglass radome: The grey fiberglass radomes of these antennas are very stable and extraordinarily stiff. They are resistant to ultraviolet radiation and can also be painted to match their surroundings. All screws and nuts: Stainless steel.
Grounding:
The metal parts of the antenna including the mounting kit and the inner conductors are DC grounded.
Environmental tests:
iRCU additionally fulfil the standards: EN 60950-1 (Safety), EN 55022 (Emission) and EN 55024 (Immunity)
64
1918 1948 1989
Input
9
C) Mechanical specifications
152 173
300
Frequency range
Array
Connector
698 – 894 MHz 1710 – 2170 MHz
R1 B1
1–2 3–4
46 49
Correlation Table 101 221
Bottom view Dimensions refer to radome. All dimensions in mm.
B1 R1
Accessories Description
Remarks
1.1 2.7 4.8 6.5
2.4 6.0 10.6 14.3
Units per antenna 2 (included in the scope of supply) 2 (order separately if required) 2 (order separately if required) 1 (order separately if required)
936.4267/a
738546 1 clamp Mast: 42 – 115 mm diameter 85010002 1 clamp Mast: 110 – 220 mm diameter 85010003 1 clamp Mast: 210 – 380 mm diameter 85010008 1 downtilt kit Downtilt angle: 0° – 11° Wall mounting: No additional mounting kit needed.
Weight approx. kg lbs
Subject to alteration.
Type No.
Page 2 of 2 80010765V01
Any previous data sheet issues have now become invalid.
www.kathrein.de
KATHREIN-Werke KG · Anton-Kathrein-Straße 1 – 3 · P.O. Box 10 04 44 · 83004 Rosenheim · Germany · Phone +49 8031 184-0 · Fax +49 8031 184-973
