Transcript
Deep Gap Slotted Switch with Wire and Connector Options OPB815L, OPB815WZ Series
L Package
Features: Wide slot width: 0.375” (9.5 mm) Deep slot depth: 0.430” (10.9 mm) Selectable wire lengths from 24” (610 mm) Seven popular connector options
Product Photo Here WZ Package
Description: The OPB815 consists of an infrared Light Emitting Diode (LED) and an NPN silicon phototransistor mounted in a low-cost plastic housing. The device is designed to switch electrical states when an opaque object is passed through the slot. The slot is wider and deeper than many slotted switches and will accommodate a variety of different materials. This device can be ordered with PCBoard solderable leads (OPB815L) or with 26 AWG stranded, UL rated wire length of 24” [610 mm] (OPB815WZ). Custom electrical, wire and cabling and connectors are available. Contact your local representative or OPTEK for more information.
Applications: Non-contact object sensing Assembly line automation Machine automation Equipment security Machine safety
Ordering Information Part
LED Peak
Aperture Emitter /Sensor
Slot
Lead Length /
OPB815L
890 nm
Transistor
0.375" / 0.430”
None
0.10" / 0.53"
OPB815WZ
890 nm
Transistor
0.375"/ 0.430”
None
24" / 26 AWG
OPB815WZ OPB815L
DIMENSIONS ARE IN:
Pin # 1
RoHS
Description
[ MILLIMETERS] INCHES
Anode
2
Cathode
3
Collector
4
Emitter
Color
Description
Red
Anode
Black
Cathode
White
Collector
Green
Emitter
OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible.
OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396
[email protected] www.optekinc.com
Issue A.5 01/14 Page 1 of 3
Deep Gap Slotted Switch with Wire and Connector Options OPB815L, OPB815WZ Series
Absolute Maximum Ratings (TA=25°C unless otherwise noted) Storage & Operating Temperature Range
-40° C to +80° C
Lead Soldering Temperature [1/16 inch (1.6mm) from the case for 5 sec. with soldering iron]
260° C
Input Infrared LED Continuous Forward Current
50 mA
Reverse Voltage Power Dissipation
2V (2)
100 mW
Output Phototransistor Collector-Emitter Voltage
30 V
Emitter-Collector Voltage
5V
Power Dissipation
(2)
100 mW
Electrical Characteristics (TA = 25°C unless otherwise noted) SYMBOL
PARAMETER
MIN
TYP
MAX
UNITS
TEST CONDITIONS
Input Infrared LED (see OP240 for additional information) VF
Forward Voltage
-
-
1.7
V
IF = 20 mA
IR
Reverse Current
-
-
100
µA
VR = 2 V
Output Phototransistor (see OP550 for additional information) V(BR)CEO
Collector-Emitter Breakdown Voltage
30
-
-
V
IC = 1 mA
V(BR)ECO
Emitter-Collector Breakdown Voltage
5
-
-
v
IE = 100 µA
Collector-Emitter Dark Current
-
-
100
nA
VCE = 10 V, IF = 0, EE = 0
Collector-Emitter Saturation Voltage
-
-
0.4
V
IC = 500 µA, IF = 20 mA
3.5
-
16
mA
VCE = 10 V, IF = 20 mA
ICEO Coupled VCE(SAT) IC(ON)
On-State Collector Current
Notes: (1) All wires are 26 AWG stranded, UL rated. (2) Derate linearly 1.67mW/°C above 25° C. (3) Methanol or isopropanol are recommended as cleaning agents. The plastic housing is soluble in chlorinated hydrocarbons and keytones. (4) All parameters tested using pulse techniques.
Test Diagram 0
Top to Bottom
Emitter Left to Right
Right to Left
Sensor 0
Width
OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. Issue A.5 01/14 Page 2 of 3
OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396
[email protected] www.optekinc.com
Deep Gap Slotted Switch with Wire and Connector Options OPB815L, OPB815WZ Series
OPB815 - Flag Next to Sensor 1.20
1.00
1.00
Typical IC(ON) Response (mA)
Typical IC(ON) Response (mA)
OPB815 - Flag Next to Emitter 1.20
0.80 Left to Right
Right to Left
0.60
Top to Bottom
0.40
0.80 Left to Right
Right to Left
0.60
0.40 Top to Bottom
0.20
0.20
0.00 0.00
0.05
0.10
0.15
0.20
0.00 0.00
0.25
0.05
Displacement Distance (inches)
0.10
0.15
0.20
0.25
Displacement Distance (inches)
Output Current vs Forward Current vs Temperature
OPB815 - Flag in Middle of Slot 1.2
3
Normalized at IF = 20mA at TA = 20°C, VCE = 10V
3
0.8
Left to Right
Normalized Output Current
Typical IC(ON) Response (mA)
1.0
Right to Left
0.6
0.4 Top to Bottom
0.2
2
2
-40° C -20° C 0° C 20° C 40° C 60° C 80° C
1
1
0.0 0.00
0
0.05
0.10
0.15
0.20
0.25
0
5
10
15
Displacement Distance (inches)
20
25
30
35
40
45
50
Forward Current - mA
Refer to Test Diagram on page 2 for definition of “Top to Bottom”, “Left to Right” and “Right to Left” OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396
[email protected] www.optekinc.com
Issue A.5 01/14 Page 3 of 3
Mouser Electronics Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
Optek: OPB815WZ OPB815L OPB815W