Transcript
Service Manual
DEH-P900R/UC
ORDER NO.
CRT2324
MULTI-CD/DAB CONTROL DSP HIGH POWER CD PLAYER WITH RDS TUNER
DEH-P900R
UC
MULTI-CD CONTROL DSP HIGH POWER CD PLAYER WITH FM/AM TUNER
DEH-P9050
ES
- See the separate manual CX-916(CRT2300) for the CD mechanism description, disassembly and circuit description. - The CD mechanism employed in this model is one of S8 series.
SERVICE PRECAUTION In the first production, the following parts had been mounted temporarily to support the microcomputer IC601 (PD5483A): R591 (RS1/16S473J), R592 (RS1/16S102J), and IC591 (Non spare part). When replacing IC601 PD5483A, use PD5483B as IC601, and then remove the 3 parts listed above. IC601 (PD5484A): R591 (RS1/16S473J), R592 (RS1/16S102J), and IC591 (Non spare part). When replacing IC601 PD5484A, use PD5484B as IC601, and then remove the 3 parts listed above.
CONTENTS 1. 2. 3. 4. 5. 6.
SAFETY INFORMATION ............................................2 EXPLODED VIEWS AND PARTS LIST .......................3 BLOCK DIAGRAM AND SCHEMATIC DIAGRAM ...10 PCB CONNECTION DIAGRAM ................................32 ELECTRICAL PARTS LIST ........................................44 ADJUSTMENT..........................................................54
7. GENERAL INFORMATION .......................................58 7.1 DIAGNOSIS ........................................................58 7.1.1 TEST MODE ..............................................58 7.1.2 DISASSEMBLY .........................................62 7.2 IC ........................................................................67 8. OPERATIONS AND SPECIFICATIONS.....................83
PIONEER ELECTRONIC CORPORATION
4-1, Meguro 1-Chome, Meguro-ku, Tokyo 153-8654, Japan PIONEER ELECTRONICS SERVICE INC. P.O.Box 1760, Long Beach, CA 90801-1760 U.S.A. PIONEER ELECTRONIC [EUROPE] N.V. Haven 1087 Keetberglaan 1, 9120 Melsele, Belgium PIONEER ELECTRONICS ASIACENTRE PTE.LTD. 253 Alexandra Road, #04-01, Singapore 159936
C PIONEER ELECTRONIC CORPORATION 1999
K-ZZB. APR. 1999 Printed in Japan
DEH-P900R,P9050
- CD Player Service Precautions 1. For pickup unit(CXX1285) handling, please refer to"Disassembly"(see page 62). During replacement, handling precautions shall be taken to prevent an electrostatic discharge(protection by a short pin).
2. During disassembly, be sure to turn the power off since an internal IC might be destroyed when a connector is plugged or unplugged. 3. Please checking the grating after changing the service pickup unit(see page 56).
1. SAFETY INFORMATION CAUTION This service manual is intended for qualified service technicians; it is not meant for the casual do-it-yourselfer. Qualified technicians have the necessary test equipment and tools, and have been trained to properly and safely repair complex products such as those covered by this manual. Improperly performed repairs can adversely affect the safety and reliability of the product and may void the warranty. If you are not qualified to perform the repair of this product properly and safely; you should not risk trying to do so and refer the repair to a qualified service technician. WARNING This product contains lead in solder and certain electrical parts contain chemicals which are known to the state of California to cause cancer, birth defects or other reproductive harm. Health & Safety Code Section 25249.6 - Proposition 65
2
DEH-P900R,P9050
2. EXPLODED VIEWS AND PARTS LIST 2.1 PACKING
20 18 19
7
24 15
17
14 9
10 11 12
13
8 1
23 6
16
5
3 4 26
2
28
22
21
27
25
3
DEH-P900R,P9050
NOTE: - Parts marked by “*” are generally unavailable because they are not in our Master Spare Parts List. - Screws adjacent to ∇ mark on the product are used for disassembly.
- PACKING SECTION PARTS LIST Part No. DEH-P9050/ES CDE5854 CEA2426 CNS5031 CZA3371 CZE3188
Mark No. 1 2 * 3 * 4 5
Description Cord Assy Base Assy Base Sheet Polyethylene Bag
DEH-P900R/UC CDE5854 CEA2426 CNS5031 CZA3371 CZE3188
6 7 8 9 10
Microphone Assy Spring Case Assy Screw Screw
CPM1022 CBH-865 CXB3520 BMZ50P060FMC CBA-102
CPM1022 CBH-865 CXB3520 BMZ50P060FMC Not used
11 12 13 14 15
Screw Screw Polyethylene Bag Screw Nut
CBA1002 CBA1120 CEG-127 CMZ50P060FMC NF50FMC
CBA1002 CBA1120 CEG-127 CMZ50P060FMC Not used
16 17 18 19 20-1
Polyethylene Bag Handle Strap Bush Polyethylene Bag
CEG-158 CNC5395 CNF-111 CNV1917 CEG1116
CEG-158 CNC5395 Not used CNV1917 CEG1116
20-2 20-3 20-4 20-5 20-6
Owner’s Manual Owner’s Manual Installation Manual Caution Card Warranty Card
CRD2965 Not used CRD2966 CRP1207 CRY1070
CRD2971 CRD2972 CRD2973 CRP1207 Not used
20-7 21 22 23 24
Caution Card Polyethylene Bag Air Cushioned Bag Battery Carton
CRP1209 CEG1185 CEG1192 CEX1006 CHG3772
CRP1210 CEG1088(Cover) CEG1192 CEX1006 CHG3770
Contain Box Protector Protector Remote Control Assy
CHL3772 CHP2032 CHP2033 CXB3875
CHL3770 CHP2032 CHP2033 CXB3875
*
*
* * *
25 26 27 28
- Owner's Manual, Installation Manual Model DEH-P900R/UC DEH-P9050/ES
4
Part No. CRD2965 CRD2966 CRD2971 CRD2972 CRD2973
Language English, French English, French English, Spanish Portuguese, Arabic English, Spanish, Portuguese, Arabic
DEH-P900R,P9050
2.2 EXTERIOR 24 24 24 122 8
11
4 14 14
17
12 12
5
2 2
101 105
123 124
16 103
6
1 1
1
104
1
128
102
21
100
125 60 3(1/2)
89
80
72
79 70
99
30
92
B
B
65
31
71 93 127
97 29
127 76
77
2
127
77
127
9 19 83
95
62
15
49
56
63
90
88
76
51
54
64
61
A
7
20
22
18
35 57
68 82
62
44
58
87
62
32
67
86
94
127
84
47 46
126
66 81
50
78
3 (2/2)
75
39 2
34 91
74 66
85
38
67
66
96
33 43
37
98 69
52
A
66
73
36
45 86
78
69
42
126
66 91
53
40
55
48 13
127
33
41
74
10
23
28 108 121
108
116 2
117 108 110
115
107
2
26 2
114
59
111 25
118
119 109
113 120
112
106
27
27
5
DEH-P900R,P9050
(1) EXTERIOR SECTION PARTS LIST Mark No. Description 1 2 3 4 5
*
*
6
Part No.
Mark No. Description
Part No.
Screw Screw Cord Cord Assy Cord Assy
BSZ26P060FMC BSZ30P050FMC CDE5536 CDE5840 CDE5842
51 52 53 54 55
Heat Sink FM/AM Tuner Unit Holder DSP Unit Connector(CN3001)
CNR1535 CWE1501 CNC7532 CWX2323 CKS3782
6 7 8 9 10
Cord Assy Connector Cord Assy IC(IC301) Transistor(Q803,921,998)
See Contrast table(2)
CDE5846 CDE5854 PAL005A 2SD2396
56 57 58 59 60
Case Case Insulator Chassis Unit Panel Assy
CNC8166 CNC8167 CNM6130 CXB3556 CXB3578
11 12 13 14 15
Fuse(10A) Cap IC(IC971) Resistor Antenna Cable
CEK1136 CNS1472 NJM7805FA RS1/2PMF102J CDH1256
61 62 63 64 65
Screw Screw Screw Screw Screw
BMZ20P030FMC CBA1154 BPZ20P060FMC CBA1060 CBA1061
16 17 18 19 20
Case Holder Earth Terminal Holder Spacer
CNB2426 CNC6798
66 67 68 69 70
Screw Screw Screw Spring Cord
CBA1082 CBA1430 CBA1454 CBH2130 CDE5856
21 22 23 24 25
Cushion Cushion Panel Cap PCB
CNM6065 CNM6387
71 72 73 74 75
Cord Mini Jack(CN4602) Connector Roller Frame
CDE5960 CKN1015 CKS3997 CLA3583 CNC8201
26 27 28 29 30
Screw Screw Insulator Cover Tuner Amp Unit
BSZ30P200FMC CBA1447 CNM6135 CNM6489 See Contrast table(2)
76 77 78 79 80
Spacer Spacer Spacer PCB PCB
CNM6155 CNM6156 CNM6419 CNP5321 CNP5341
31 32 33 34 35
Screw Clamper Clamper Clamper Plug(CN901)
BMZ26P160FMC CEF1004 CEF1008 CEF1009 CKM1278
81 82 83 84 85
PCB Panel Lighting Conductor Cover Guide
CNP5355 CNS5232 CNV5605 CNV5610 CNV5672
36 37 38 39 40
Plug(CN141) Plug(CN251) Plug(CN131) Plug(CN851) Plug(CN101)
CKS-766 CKS-783 CKS-784 CKS-786 CKS1058
86 87 88 89 90
Guide Rack Gear Gear Torque Limiter Unit
CNV5696 CNV5697 CNV5698 CNV5761 CNV5762
41 42 43 44 45
Connector(CN801) Connector(CN991) Connector(CN681) Connector(CN351) Connector(CN252)
CKS1532 CKS1960 CKS3597 CKS3606 CKS3781
91 92 93 94 95
Holder Switch(S951) Switch(S952) Arm Unit Frame Unit
CNV5763 CSN1012 CSN1022 CXB3574 CXB3575
46 47 48 49 50
Mini Pin Jack(CN451) Holder Holder Holder Insulator
CKX1046
96 97 98 99 100
Holder Unit Bracket Unit Arm Unit Motor(M951) ASL Unit
CXB3576 CXB3577 CXB3866 CXM1085 CWX2322
See Contrast table(2)
CNC8170 See Contrast table(2)
See Contrast table(2)
CNV2680 CNP5508
See Contrast table(2)
CNC8168 CNC8169 See Contrast table(2)
DEH-P900R,P9050
Mark No. 101 102 103 104 105
Description Screw Cord Assy Plug(CN4501) Case Case
Part No. BSZ30P055FMC CDE5845 CKS-784 CNB2299 CNB2300
106 107 108 109 110
Detach Grille Assy Screw Screw Button( ) Button(D)
See Contrast table(2)
111 112 113 114 115
Button(SOURCE) Button( ) Button(EQ) Button(1-6) Housing
See Contrast table(2) See Contrast table(2) See Contrast table(2) See Contrast table(2)
BPZ20P060FMC BPZ20P080FZK See Contrast table(2)
CAC5891
Mark No. 116 117 118 119 120 121 122 123 124 125
Description Keyboard Unit Connector(CN1902) Connector(CN1901) OEL Module Grille Unit Cover Unit Case Assy Remote Control Assy Battery Cover
Part No. CWM6226 CKS3995 CKS3996 MXK8002 See Contrast table(2) See Contrast table(2)
CXB3520 CXB3875 CNS5032 CD Mechanism Module(S8) CXK5252
126 Washer 127 Washer 128 Cord Assy
2-1816-0035-D2-00 2-1821-0045-D2-00 See Contrast table(2)
CNV5606
(2) CONTRAST TABLE DEH-P900R/UC and DEH-P9050/ES are constructed same except for the following:
Description Cord Assy Earth Terminal Spacer Panel Tuner Amp Unit
Part No. DEH-P900R/UC DEH-P9050/ES CDE5843 Not used CNC7358 CNC6469(Holder) CNM6482 CNM4870(Cushion) CNS5256 CSN5548 CWM6214 CWM6216
47 50 106 109 111
Holder Insulator Detach Grille Assy Button( ) Button(SOURCE)
CNC7533 CNM5967 CXB3273 CNC5890 CNC5892
Not used Not used CXB3978 CNC6126 CNC5901
112 113 114 120 121
Button( ) Button(EQ) Button(1-6) Grille Unit Cover Unit
CNC5893 CNC5894 CNC5896 CXB3272 CXB4309
CNC6045 CNC5899 CNC5911 CXB3982 CXB4310
128
Cord Assy
Not used
CDE5844
Mark No. 6 18 20 23 30
7
DEH-P900R,P9050
2.3 CD MECHANISM MODULE
8
DEH-P900R,P9050
- CD MECHANISM MODULE SECTION PARTS LIST Mark No. 1 2 3 4 5
*
Description Control Unit Connector(CN802) Connector(CN801) Connector(CN701) Connector(CN101)
Part No. CWX2359 CKS2192 CKS2193 CKS2771 CKS3486
6 7 8 9 10
Screw Screw Screw(M2×3) Screw(M2×6) Screw
BMZ20P030FZK BSZ20P040FZK CBA1077 CBA1489 CBA1243
11 12 13 14 15
Screw(M2×4) Washer Washer Washer Washer
16 17 18 19 20
Mark No. 46 47 48 49 50
Description Sheet Ball Belt Roller Arm
Part No. CNM6215 CNR1189 CNT1086 CNV4509 CNV5246
51 52 53 54 55
Arm Arm Arm Guide Guide
CNV5247 CNV5248 CNV5249 CNV5254 CNV5255
CBA1362 CBF1037 CBF1038 CBF1060 CBF1075
56 57 58 59 60
Gear Gear Guide Damper Arm
CNV5257 CNV5256 CNV5869 CNV5266 CNV5359
Spring Spring Spring Spring Spring
CBH2079 CBH2117 CBH2278 CBH2110 CBH2282
61 62 63 64 65
Arm Arm Guide Guide Holder
CNV5360 CNV5361 CNV5509 CNV5510 CNV5578
21 22 23 24 25
Spring Spring Spring Spring Spring
CBH2114 CBH2115 CBH2080 CBH2118 CBH2161
66 67 68 69 70
Guide Clamper Gear Motor Unit(M1) Screw Unit
CNV5751 CNV5758 CNV5813 CXB2190 CXB2191
26 27 28 29 30
Spring Spring Spring Spring Spring
CBH2163 CBH2189 CBH2249 CBH2260 CBH2262
71 72 73 74 75
Chassis Unit Gear Unit Arm Unit Motor Unit(M2) Lever Unit
CXB2192 CXB2193 CXB2194 CXB2195 CXB2553
31 32 33 34 35
Spring Spring Connector Connector Shaft
CBL1367 CBL1369 CDE5531 CDE5532 CLA3304
76 77 78 79 80
Arm Unit Motor Unit(M3) Arm Unit Bracket Unit Screw
CXB2554 CXB2562 CXB2795 CXB4071 JFZ20P025FMC
36 37 38 39 40
Screw(M2.6×6) Frame Frame Lever Arm
CBA1458 CNC7544 CNC7545 CNC7546 CNC7739
81 82 83 84 85
Screw Washer Pickup Unit(Service)(P8) Screw PCB
JGZ17P025FZK YE15FUC CXX1285 IMS26P030FMC CNX2982
41 42 43 44 45
Bracket Plate Spacer Sheet Cushion
CNC7798 CNC8090 CNM3315 CNM6170 CNM6204
*
86 Photo-transistor(Q1, 2) 87 Connector(CN702)
CPT230SX-TU CKS2191
9
2
1
3
4
DEH-P900R,P9050
3. BLOCK DIAGRAM AND SCHEMATIC DIAGRAM 3.1 BLOCK DIAGRAM
A
A
E
TUNER AMP UNIT
ASL UNIT ASL A
MIC4501 Q4501 VR4501 3
B
FM/AM TUNER UNIT FM/AM 1ST IF 10.7MHz T51 Q51 CF51 CF52 CF53
FM FRONT END Q3
CN451 ANT GND2
1
FM MPX 25
27
24
32
2
39
42
44
46
63
RF TV
22
Q501
6
RDS DECODER
46
VDD
24 fm/AM
70 54
MIXER.IF AMP DET IC 1 PML002A
COMP
21
11
71 33 45
55 57
28
CF202
61 74
81
75
SYSTEM CONTROLLER IC 601(1/2) PD5483A(/UC) PD5484A(/ES)
12
/UC
X501
EEPROM 5
AM RF
6
AM 2ND IF 450kHz
49
4
IC 3 BR9010FV
97
3
94 FMSD
SL
SDBL
CE1
3 2 4
2
1
SD
13 SL
CK CK
8 SD2
B
PDIO
Q401
12 15 16 CE1
22 10 14
PCE2
25
CE2
DI/DO
VCC VDD
78
LOCL
POWER ON MUTE
10
Q101
IC 401 S-81250SGUP
SYS+B TUN5V
30
B.U
B.U
29 ASENBO
5 6 8
1
IC 101 CA008AM
5 BUS2
CONTROL UNIT
1 BUS1
42
7 BUS+L
43
11 BUS–L
44
40
2
SD_BW TUNPCE TUNPCK TUNPCE2 PDIO
LOCL ASENBO TX RX IPPW
RX IPPW
CN251
36
A
1
PICKUP UNIT(SERVICE)
SL
TX
2
8
CN101
IP-BUS CONNECTOR
7
SD
IP-BUS DRIVER
Q102
2
FM/AM
IC 501 PM4009A
20
65
35
Q201 Q204
19
IC 2 PM4008A 34 33 41 44 11
69
ANT2 TV
ANT1 TV
38
H
IC 45 NJM2
37
IN3_L IN4+_L
ELECTRICAL V SOURCE SELE
IN4–_L
IC 203 PML004A
VREF IN2_R IN1_R
1
CN702
LD MD
LD+ MD
Q101
CN101
CN701 98
14
97
B+D/E 24
FO+ TO+
4 3
M
12 11 CN801
LOADING MOTOR
1
M
CN991 LOUT/LRCK
LRCK
ROUT/DOUT
DOUT
14
3
TOP
SOP
SD/MD
DATAO
IC 601 PD0236AM
BCKO LRCKO
8 7
7
16
5
18
24
PEE
AGND/SCKO
ASENS
5
HOME
EMPH
27
9
14
EMPH
TELIN
CD5V
DRSYS DRSENS
S801 HOME
DRELAY
SOM
SINGLE-CD CONTROLLER
COP FWD REV MUTE
1
58
28
57
21
55
CDLOAD
reset
1 2
1 VD
60
SYSPW
Q901
CONT
AVREF ADENA
9
VDD
47
EJTSNS
V+5
CLAMP
CD5VON VDCONT
S802 CLAMP
BMUTE
11
11
VDD
12
12
VD
21
2
22
1
VDD
Q998
DALMON
IC 601(2/2) PD5483A(/UC) PD5484A(ES)
B.U
+5V REGULATOR IC 701 BA05SFP
4
DSCSNS
D803 D802 D801
SYSTEM CONTROLLER
B
10
CDEJET
IC 901 PE5011C
3
IN
MUTE
2
Q991
1
31 48 59
13
10
20
3
Q851
BMUTE
DISC SENSE
I
Q641
BSENS
39
CN802
2
14 DATA 15 BCKI 11 LRCKI
RF-AMP, DSP, SERVO, DAC
4
SELECT SENSE
SP601 ALARM BUZZER
BIT LENGTH EXPANSION
ISENS FOP
13 COM 10 LOP 9 LOM
2
M
15
TD/FD
CD DRIVER
17
CARRIAGE MOTOR
IC 201 UPD63710GC
TOP
16
SPINDLE MOTOR
17
8
SCKO
FOP
IC 301 BA5985FM
C
PD
6
A+C/F
HOLOGRAM UNIT FOCUS ACT TRACKING ACT
30 DOUT SCKO 32 34 LRCK
LD
5
B.U
Q852
PHOTO UNIT FLPPW M951 AUTOMATIC FLAP MOTOR
F
M
CN851 5
S951 CLOSE S952 OPEN
BLUE RED WHITE
3 2
3 14
4
SWITCH PCB
FLAP MOTOR CONTROL OUT1 OUT2
4
26
FLPPW
Q853
5
IC 851 FIN BA6288FS FIN
DSENS
6
FLPOPN
34
11
FLPCLS
37
FLPOPN FLPCLS
FCLSSW
KYDT
FOPNSW
40 38
1
FCLSSW
DPDT
FOPNSW RESET
CN131
Q132 VDD
1 2
DALMON
3
D
G
DALMON
Q131
MIC JACK PCB
MICSEN
28
MICSENS FLPILM
Q684
ALARM SENSOR
3
DOOR LOCK
2
STARTER CUT-OFF
1
CN681 MOTS1
MOSENS
5
DLSENS
6
DFS ALARM STOUT
75
10 3
DLSENS ILMPW
/UC
IC 681 TPD1018F
2
OEL PW
Q685
DRLC1
ST1
1
MOSENS
4
SOUT
SWVDD
5
7
6
8
DEH-P900R,P9050
A
D ASL AMP
501 3
IC 4501 NJM2068
ASL FILTER 1
3
IC 4502 NJM2068
DSP UNIT
CN141 1
2
2
X3101
NOISE
BUFFER IC 3203(1/2) HD74HCT126FP CN252
CN3001
DOUT SCKO LRCK
4
4
3
3
2
2
35
35
28
6
23
9
8
37
11
12
36
LIN–
8
CN3001
SDIN
78
BITCLK
IC 3101 AK7714 DSP, DAC 98
8
IC 3301 NJM4580M
3
AOUTL1
1
FREQUENCY CONVERSION
CLKO
35
IC 3201 74HC393AF
1
AINL–
8 1 REF
CN252
12
12
5
5
BUFFER IC 3203(2/2) HD74HCT126FP
LRCLK
13 NOISE
27
AMP
5
IC 3202 CKO TC9246F
10 2
3
A 1
DSP CONTROLLER
58 74 LRCKK NOISE
TEM OLLER (1/2) A(/UC) 4A(/ES)
IC 3001 PD5504A EMPHIN 8
EMPH
30
59 MCKOUT
VSTD/VDTD/VCKD
10
12
reset DSPPW MUTERQ NGO 9 40 41 42 PLL5V
DSP5V
30 X3001 CN3001
1
29
18
6
17
16
1
29
18
6
17
16
CN252
BMUTE
RESET
MUTERQ ZDF LOUT
DSPPW
Q972 3
B.U
B
5V REG.
Q911
Q291
IC 971 NJM7805FA
1
VDD
B.U
B.U
Q913
Q292
CD5V
Q971
DALMON
B.U
ELECTRICAL VOLUME/ SOURCE SELECTOR
2
PV IN_L
10
FL
IC 203 PML004AF
12
IC 301 PAL005A
FL 14 RF
11
RL
9
PREL
1
BACKUP
2
GND
POWER AMP
1
Setout_L
BACKUP
MUTE
STBY
B.REM
22
4
25
23
RL–
21
RL+
3
FL–
5
FL+
SYSPW
B.REM
9
RL–
11
RL+
10
FL–
12
FL+
4
B.REM
3
ILL
5
ACC
8
MUTE
7
DOOR SW
Q932 ILL
ILL
Q301 MUTE Q931 asens
Q302 ASENS
BSENS ISENS TELIN DRSYS DRSENS DRELAY
SYSPW
TEM OLLER
ACC
bsens
B.U
74
Q951 Q982
73
TELIN
TEL1
23
Q681
11 CN351
87
FRONT L CH
7
86
7
76
11
SWL1
Q353
9
RLI
FLI
22
IC 271 PA2028A
20
HIGH OUT
FLO RLO
DOOR SW
B.U DRSYS
Q682
DRSENS
14
REAR L CH
3
SWLO 18
Q355
C
Q683
6
16
Q941
2
ALARM
B.U DALMON
DALMON
(2/2) A(/UC) 4A(ES)
Q261
Q351
10
B.U
SYSPW MUTE
SUB WOOFER L CH
11
6
ALARM
DRELAY
Q942
27
Q921
DZF
Q923
SYS+B
B.U
MUTERQ
Q981
BMUTE
C
Q922
KEYBOARD UNIT REMOTE CONTROL SENSOR
CN1901
CN801 DSENS
47
12
1
IC 1903 RS-140
4
SWVDD
DSENS
97
DPDT
RESET
36 35
12
RESET
B
1
Q962
B.U
RESET IC 961 S–80735ANDZI
2
9
4
8
5
33 34
VDD
6
7
2
11
11
2
OEL PW
IC 1902 PD8051A
DPDT ADRESS
S1925
KEY AND OEL MODULE CONTROLLER
KEY MATRIX
IC 1901 PD5471A
Q803 43
Q808 Q805
4
9
ILB
5
8
SWVDD 11
46
D
13 EW ONLY
Q806
X1901 ILB
B.U
Q801 ILMPW
44
18 17
B.U
Q807 SWVDD
25
DATA
REM
KYDT
RST VDD
B.U FLPILM
SWVDD
DATA ROM
5
14
AVCC VDD KYDT
OPT IN
1
CN1902
1-15
Q802 OEL MODULE MXK8002
45
11 5
6
7
8
2
1
3
4
DEH-P900R,P9050
3.2 OVERALL CONNECTION DIAGRAM(GUIDE PAGE) Note: When ordering service parts, be sure to refer to “EXPLODED VIEWS AND PARTS LIST” or “ELECTRICAL PARTS LIST”.
A-a
A 4
3
2
A-a
A-b
Large size SCH diagram
IP-BUS
11 10
1 6
7 9
5 8
CD,TUNER,IP-BUS SIGNAL TUNER SIGNAL IP-BUS SIGNAL CD(DIGITAL) SIGNAL
H I
CD MECHANISM MODULE CN701
IP-BUS:+2.2dBs
A-a
A-b
Guide page
CD MECHANISM A-a
A-b
Detailed page
IP-BUS DRIVER
AUTO-EQ
B IP-BUS:+2.2dBs FM(100%):-20.5dBs AM(30%):-31dBs
CN4602
MIC JACK
G PCB
FM/AM TUNER UNIT
FM(100%):-19.5dBs AM(30%):-30dBs
/UC
B
TUNER
/ES
C433
100P
C
EEPROM
AUTOMATIC FLAP
RDS DECODER
D
12
A F G 1
F 2
3
S951 CSN1012
M951 AUTOMATIC FLAP MOTOR CXM1085
OPEN
S952 CSN1022
CLOSE
/UC
SWITCH PCB 4
C
K
5
7
6
8
DEH-P900R,P9050
A-b
E
A
ASL UNIT
A
CN4501
TUNER AMP UNIT
ASL IP-BUS:+4.3dBs FM(100%):-0.4dBs AM(30%):-10.9dBs
H CN702 R284 0R0
/ES
D CN3001
PRE OUT
/UC
PRE OUT
CD:+2.43dBs
DSP
E-VOL
B
Bs CD:+8.18dBs CD:+18.68dBs
RESET AMP
(/UC) (/ES)
C
CEK1136 10A BACK UP GND ILL
SYSTEM CONTROLLER
1K(1/2W) 1K(1/2W)
B REMOTE ACC
0.5A
BUZZER
ALARM
CEK1014
DOOR SW CELLULAR MUTE RLFL-
VDD 5V 8V REGULATOR
RL+ FL+ RRFRRR+ FR+
CD:+34.18dBs
SENSE
MUTE
TEL MUTE
/UC
DFS ALARM
GRILLE
ALARM SENSOR DOOR LOCK STARTER CUT-OFF
CN1901
KEYBOARD UNIT
5
6
7
A 8
13
D
14
A-a G
1
D
2
3
G
MIC JACK PCB
CN4602
6
8
5
IP-BUS DRIVER
9
7
11 10
1
FM(100%):-19.5dBs AM(30%):-30dBs
IP-BUS:+2.2dBs
/UC
CD,TUNER,IP-BUS SIGNAL TUNER SIGNAL IP-BUS SIGNAL CD(DIGITAL) SIGNAL
CD MECHANISM
H I
CD MECHANISM MODULE CN701
IP-BUS:+2.2dBs FM(100%):-20.5dBs AM(30%):-31dBs
ASL
E-VOL
CN4501
ASL UNIT
E
CD:+
3
3
2
1
2
AUTO-EQ
IP-BUS
2
B
3
4
A
A-a A-b
1
M TUNER UNIT
DEH-P900R,P9050
4
C
4
6
7
EEPROM
/UC
RDS DECODER
OPEN
SWITCH PCB
C
A-a A-b
KEYBOARD UNIT
CN1901
SYSTEM CONTR
(/UC) (/ES)
7
F
M951 AUTOMATIC FLAP MOTOR CXM1085
AUTOMATIC FLAP
/ES
100P C433
TUNER
CLOSE S951 CSN1012
5
6
S952 CSN1022
5
DEH-P900R,P9050
8
A-a F
8
15
A
B
C
FM/AM TU
B
D
16
A-b
1
2
C RESET
CN3001
AMP
/ES
/UC
PRE OUT
CD:+18.68dBs
PRE OUT
3
3
3
D
CD:+8.18dBs
DSP
D
H CN702
TUNER AMP UNIT
2
2
1
IP-BUS:+4.3dBs FM(100%):-0.4dBs AM(30%):-10.9dBs
B
A
1
R284 0R0
A
A-a A-b
DEH-P900R,P9050
4
4
CD:+2.43dBs
5 BUZZER
6 /UC
DFS ALARM
MUTE
8V REGULATOR
TEL MUTE
VDD 5V
SENSE
BACK UP
FR+
RR+
FR-
RR-
FL+
RL+
FL-
RL-
CELLULAR MUTE
DOOR SW
ALARM
ACC
B REMOTE
ILL
GND
7
A-a A-b
STARTER CUT-OFF
DOOR LOCK
ALARM SENSOR
CD:+34.18dBs
CEK1014
0.5A
1K(1/2W) 1K(1/2W)
CEK1136 10A
6
UNIT
CN1901
GRILLE
M CONTROLLER
(/UC) (/ES)
AMP
5 7
DEH-P900R,P9050
8
A-b
8
17
A
B
C
D
2
1
3
4
DEH-P900R,P9050
3.3 FM/AM TUNER UNIT
A
A
B Voltage of IC Terminals Mark None F0 F65 F125 A0 A74 A125
Band – FM FM FM AM AM AM
Input Level – 0dBf 65dBf 125dBf 0dBµ 74dBµ 125dBµ
KV1410(23)
B
C
D
18
B 1
2
3
4
5
6
7
8
DEH-P900R,P9050
KV1410(23)
A
B
C
D
5
6
7
B 8
19
1
2
3
4
DEH-P900R,P9050
3.4 KEYBOARD UNIT A
EQ-
S1901,1902:CSG1112 S1903,1904:CSG1111 S1905-1924:CSG1112 S1925:CSG1111
B
EQ+ VOL+
DISP
PGM
ENT
SOURCE
VOL-
5
3
2
1
CLOCK
LOUD
6
4
AUDIO
BAND
FUNC
EJECT
RESET
C
D
20
C 1
A 2
3
CN801 4
5
6
7
8
DEH-P900R,P9050
A
C
KEYBOARD UNIT
B
C
D
5
6
7
C 8
21
1
2
3
4
DEH-P900R,P9050
3.5 DSP UNIT A
FREQUENCY CONVERSION
BUFFER
B
C
DSP, DAC
AMP
D
22
D 1
2
3
4
5
7
6
8
DEH-P900R,P9050
A
D
DSP UNIT
CD,TUNER,IP-BUS SIGNAL TUNER SIGNAL IP-BUS SIGNAL CD(DIGITAL) SIGNAL
B
A CN252
DSP CONTROLLER C
D
5
6
7
D 8
23
2
1
3
4
DEH-P900R,P9050
3.6 ASL UNIT
E
A
ASL UNIT
AMP
A
CN141
MICROPHONE
B
FILTER C
D
24
E 1
2
3
4
DEH-P900R,P9050
25
2
1
3
4
DEH-P900R,P9050
3.7 CD MECHANISM MODULE
H
CONTROL UNIT
A
PICKUP UNIT(SERVICE)
RF-AM B
CN101
SWITCHES: CONTROL UNIT S801 : HOME SWITCH.....ON-OFF S802 : CLAMP SWITCH....ON-OFF The underlined indicates the switch position.
CD DRIVER C
I
PHOTO UNIT
Q1 CPT230SX-TU Q2 CPT230SX-TU
CN802
SPINDLE MOTOR M3 CXB2562
CN801
CARRIAGE MOTOR M1 CXB2190
D LOADING MOTOR M2 CXB2195
5V REGULATOR
26
H I 1
2
3
4
5
6
7
8
DEH-P900R,P9050
A
BIT LENGTH EXPANSION
RF-AMP,SERVO,DSP,DAC
A
CN251
B
8.380MHz
CN702
CN991
C
CN701
A
SINGLE-CD CONTROLLER
D
5
6
7
H 8
27
DEH-P900R,P9050 Note:1. The encircled numbers denote measuring pointes in the circuit diagram. 2. Reference voltage REFO:2.5V
- Waveforms 1 RFI 0.5V/div. 0.5µs/div. Normal mode: play
1 CH1: RFI 1V/div. 0.5ms/div. 2 CH2: MIRR 5V/div. Test mode: Tracking open
1 CH1: RFI 1V/div. 0.5ms/div. 2 CH2: MIRR 5V/div. Normal mode: The defect part passes 800µm
REFO →
REFO →
REFO →
REFO →
REFO →
3 CH1: FD 0.5V/div. 0.2s/div. 4 CH2: FO+ 2V/div. Test mode: No disc, Focus close
3 CH1: FD 0.5V/div. 0.2s/div. 5 CH2: FOK 2V/div. Normal mode: Focus close
6 CH1: FE 0.5V/div. 1ms/div. 7 CH2: XSI 2V/div. Normal mode: Focus close
REFO → REFO →
REFO →
REFO →
REFO →
REFO →
8 CH1: TE 0.5V/div. 0.5ms/div. 9 CH2: TD 0.5V/div. Test mode: 32 tracks jump (REV)
8 CH1: TE 0.5V/div. 0.5ms/div. 9 CH2: TD 0.5V/div. Test mode: Single jump (REV)
GND →
8 CH1: TE 0.5V/div. 5ms/div. 9 CH2: TD 0.5V/div. Test mode: 100 tracks jump (REV)
REFO →
REFO →
REFO →
REFO →
REFO →
REFO →
6 CH1: FE 0.1V/div. 3 CH2: FD 0.2V/div. Normal mode: Play
20ms/div.
3 CH1: FD 0.5V/div. 0.5s/div. 0 CH2: MD 1V/div. Normal mode: Focus close (12cm)
3 CH1: FD 0.5V/div. 0.5s/div. 0 CH2: MD 1V/div. Normal mode: Focus close (8cm)
REFO →
REFO →
REFO →
REFO →
REFO →
REFO →
28
DEH-P900R,P9050
8 CH1: TE 0.2V/div. 9 CH2: TD 0.2V/div. Normal mode: play
20ms/div.
REFO →
8 CH1: TE 0.5V/div. 5ms/div. ! CH2: SD 0.5V/div. TEST mode: 100 Tracks jump(FWD)
0 MD
0.5V/div.
0.1s/div.
Normal mode: Play (12cm)
REFO → REFO →
REFO →
REFO →
0 MD 1V/div. Normal mode: Long Search (12cm)
10ms/div.
@ EFM
1V/div.
5µs/div.
Normal mode: play
8 CH1: TE 1V/div. 2ms/div. # CH2: TEC 1V/div. Test mode: Focus close Tracking open
REFO → REFO →
REFO → REFO → GND →
8 CH1: TE 0.5V/div. 0.2s/div. 6 CH2: FE 0.5V/div. Normal mode: AGC after focus close
$ PLCK
2V/div.
0.5µs/div.
Normal mode: play
% SCKO
2V/div.
1µs/div.
Normal mode: play
REFO →
REFO →
^ Dout
2V/div.
Normal mode: play
10µs/div.
REFO →
REFO →
GND →
GND →
& LRCK
2V/div.
Normal mode: play
20µs/div.
* VD
5V/div.
50ms/div.
Normal mode: No disc
GND → REFO →
REFO →
GND →
GND →
29
DEH-P900R,P9050
6 CH1: FE 0.2V/div. 1ms/div. 3 CH2: FD 0.5V/div. Normal mode: During AGC
8 CH1: TE 0.2V/div. 1ms/div. 9 CH2: TD 0.5V/div. Normal mode: During AGC
REFO →
REFO →
REFO →
REFO →
1 CH1: RFI 1V/div. 0.5ms/div. ⁄ CH2: HOLD 5V/div. Normal mode: The defect part passes 800µm(B.D)
3 CH1: FD 1V/div. 0.5ms/div. ⁄ CH2: HOLD 5V/div. Normal mode: The defect part passes 800µm(B.D)
9 CH1: TD 0.1V/div. 0.5ms/div. ⁄ CH2: HOLD 5V/div. Normal mode: The defect part passes 800µm(B.D)
REFO →
REFO →
REFO →
REFO →
REFO → REFO →
30
DEH-P900R,P9050
31
2
1
3
4
DEH-P900R,P9050
4. PCB CONNECTION DIAGRAM
CORD ASSY
MAIN ANTENNA
4.1 TUNER AMP UNIT NOTE FOR PCB DIAGRAMS A
1. The parts mounted on this PCB include all necessary parts for several destination. For further information for respective destinations, be sure to check with the schematic diagram. 2. Viewpoint of PCB diagrams Connector
Capacitor
SIDE A
P.C.Board
Chip Part
A
SIDE B
PRE OUT
TUNER AMP UNIT
B
E
CN4501
D
CN3001
C
H
CN701
D
32
A 1
M951 2
F 3
H
CN702 4
G
5
7
6
8
DEH-P900R,P9050
B
SIDE A
A
IP-BUS IN
B
CORD ASSY C
D
C 5
6
CN1901 7
A 8
33
1
2
3
4
2
3
4
DEH-P900R,P9050
A
TUNER AMP UNIT
A
B
C
D
34
A 1
5
6
7
8
DEH-P900R,P9050 SIDE B
A
B
C
D
5
6
7
A 8
35
2
1
3
4
DEH-P900R,P9050
4.2 FM/AM TUNER UNIT
SIDE A
A
A
B
FM/AM TUNER UNIT
C
B
D
36
B 1
2
3
4
1
2
3
4
DEH-P900R,P9050
SIDE B A
B
FM/AM TUNER UNIT
C
B
D
1
2
3
B 4
37
2
1
3
4
DEH-P900R,P9050
4.3 KEYBOARD UNIT
C
KEYBOARD UNIT
SIDE A
C
KEYBOARD UNIT
SIDE B
OEL MODULE
6
A
T.I
CN801
CLOCK
EJECT
BAND
FUNC
AUDIO
A
2
3
4
5
B
D
38
C 1
SOURCE EQ-
RESET
VOL-
VOL+
EQ+
DISP
ENT
PGM
1
C
2
3
4
1
2
3
4
DEH-P900R,P9050
4.4 DSP UNIT
D
DSP UNIT
A
SIDE A
B
DSP UNIT
SIDE B
C
CN252
D
A
D
1
2
3
D 4
39
1
2
3
4
DEH-P900R,P9050
4.5 ASL UNIT A
E
ASL UNIT
A
CN141
SIDE A
B
E
ASL UNIT
SIDE B
C
D
40
E 1
2
3
4
1
3
2
4
DEH-P900R,P9050
4.6 SWITCH PCB A
F
SWITCH PCB
BLUE RED WHITE
A
CN851 B
4.7 MIC JACK PCB
MIC JACK PCB
A
BLUE
RED
C
WHITE
G
CN131
D
1
2
3
F G 4
41
H
D
42
H I
1
I
A
H
CN802
M3 SPINDLE MOTOR
M1 CARRIAGE MOTOR M2 LOADING MOTOR
I
2
2
3
3
3 2 1
CN991
REFO
CN251
1
PHOTO UNIT
A
PICKUP UNIT(SERVICE)
C
EF
CONTROL UNIT
DEH-P900R,P9050
4
4.8 CD MECHANISM MODULE SIDE A
A
B
4
1
3
2
4
DEH-P900R,P9050
SIDE B A
H CONTROL UNIT B
C
1
25
100
26
76
50 75
51
D
1
2
3
H 4
43
DEH-P900R,P9050
5. ELECTRICAL PARTS LIST NOTES: - Parts whose parts numbers are omitted are subject to being not supplied. - The part numbers shown below indicate chip components. Chip Resistor RS1/_S___J,RS1/__S___J Chip Capacitor (except for CQS.....) CKS....., CCS....., CSZS..... =====Circuit Symbol and No.===Part Name --- -----------------------------------------------
A
Part No. -------------------------
Unit Number : CWM6214(DEH-P900R/UC) Unit Number : CWM6216(DEH-P9050/ES) Unit Name : Tuner Amp Unit
MISCELLANEOUS
=====Circuit Symbol and No.===Part Name --- -----------------------------------------------
Part No. -------------------------
Q Q Q Q Q
932 941 942 951 962
Transistor Transistor Transistor Transistor Transistor
DTC114EK 2SB1243 DTC124EK 2SA1162 2SC2412K
IC IC IC IC IC
101 203 271 301 401
IC IC IC IC IC
CA0008AM PML004AF PA2028A PAL005A S-81250SGUP
Q Q Q Q Q
971 972 981 982 991
Transistor Transistor Transistor Transistor Transistor
DTC123EK 2SB1238 2SC2412K 2SC2412K IMD2A
IC IC IC IC IC
501 601 681 851 961
IC IC IC IC IC
See Contrast table See Contrast table See Contrast table BA6288FS S-80735ANDZI
Q D D D D
998 131 271 291 401
Transistor Diode Diode Diode Diode
2SD2396 MA3039(L) See Contrast table MA3056(M) 1SR154-400
IC Q Q Q Q
971 101 102 131 132
IC Transistor Transistor Transistor Transistor
NJM7805FA 2SA1162 DTC124EK 2SC2412K IMD2A
D D D D D
402 681 682 683 801
Diode Diode Diode LED Diode Network
HZS16(2) See Contrast table See Contrast table BR4361F DA204U
Q Q Q Q Q
261 291 292 301 302
Transistor Transistor Transistor Transistor Transistor
IMD2A 2SD1859 IMD2A DTC124EK DTC124EK
D D D D D
802 803 804 805 806
Diode Network Diode Network Diode Network Diode Diode
DA204U DA204U DA204U MA3056(M) HZS9L(C2)
Q Q Q Q Q
351 352 353 354 355
Transistor Transistor Transistor Transistor Transistor
2SC3326 2SC3326 2SC3326 2SC3326 2SC3326
D D D D D
807 808 809 810 851
LED LED LED Diode Diode
CL170PGCD CL170PGCD CL170PGCD MA3062(M) HZS7L(C3)
Q Q Q Q Q
356 401 501 641 681
Transistor Transistor Transistor Transistor Transistor
2SC3326 2SC2412K See Contrast table DTC114EK 2SA1162
D D D D D
852 853 901 902 903
Diode Diode Diode Diode Diode
1SS133 1SS133 ERA15-02VH ERA15-02VH ERA15-02VH
Q Q Q Q Q
682 683 684 685 801
Transistor Transistor Transistor Transistor Transistor
DTC124EK 2SC2412K 2SC2412K 2SC2412K 2SD1760F5
D D D D D
911 912 921 931 932
Diode Diode Diode Diode Diode
ERA15-02VH HZS6L(B1) HZS9L(C1) HZS7L(A1) HZS7L(C3)
Q Q Q Q Q
802 803 805 806 807
Transistor Transistor Transistor Transistor Transistor
IMD2A 2SD2396 2SC2412K 2SB1238 DTC143EK
D D D D D
933 941 942 951 961
Diode Diode Diode Diode Diode
ERA15-02VH ERA15-02VH ERA15-02VH MA152WK MA152K
Q Q Q Q Q
808 851 852 853 911
Transistor Transistor Transistor Transistor Transistor
IMD2A 2SD1760F5 DTA114EK DTC124EK 2SD1760F5
D D D D D
971 981 982 983 984
Diode Diode Diode Diode Diode
MA152WK MA152WK HZS9L(A2) MA152K MA152WK
Q Q Q Q Q
913 921 922 923 931
Transistor Transistor Transistor Transistor Transistor
IMD2A 2SD2396 DTC114EK 2SB1238 IMX1
D D ZNR L L
985 991 451 101 141
Diode Diode Surge Protector Inductor Inductor
1SS133 HZS9L(B1) DSPS-201M-S00B LAU3R3K CTF1420
44
DEH-P900R,P9050
=====Circuit Symbol and No.===Part Name --- -----------------------------------------------
Part No. -------------------------
=====Circuit Symbol and No.===Part Name --- -----------------------------------------------
Part No. -------------------------
L L L L L
251 252 271 401 402
Ferri-Inductor Ferri-Inductor Ferri-Inductor Ferri-Inductor Inductor
LAU2R2K LAU1R0M LAU101K LAU2R2K LCTB4R7K2125
R R R R R
351 352 353 354 355
RS1/10S820J RS1/10S820J RS1/10S820J RS1/10S820J RS1/10S820J
L L L L L
403 404 501 502 601
Inductor Inductor Inductor Inductor Inductor
CTF1420 LCTA1R0J3225 See Contrast table See Contrast table LAU100K
R R R R R
356 357 358 359 360
RS1/10S820J RS1/16S223J RS1/16S223J RS1/16S223J RS1/16S223J
L L L X X
801 802 951 501 601
Inductor Inductor Ferri-Inductor Crystal Resonator 3.648MHz Radiator 10.00MHz
LAU100K CTF1484 LAU2R2K See Contrast table CSS1475
R R R R R
361 362 363 364 365
RS1/16S223J RS1/16S223J RS1/16S103J RS1/16S103J RS1/16S103J
SP
641
Buzzer DSP Unit FM/AM Tuner Unit
CPV1012 CWX2323 CWE1501
R R R R R
366 367 368 369 370
RS1/16S103J RS1/16S103J RS1/16S103J RS1/16S471J RS1/16S471J
RESISTORS R R R R R
101 102 103 104 105
RS1/10S101J RS1/10S620J RS1/10S101J RS1/10S222J RS1/10S103J
R R R R R
371 372 373 374 375
RS1/16S471J RS1/16S471J RS1/16S471J RS1/16S471J RS1/10S0R0J
R R R R R
106 107 108 109 110
RS1/10S562J RS1/10S332J RS1/16S102J RS1/16S102J RS1/16S223J
R R R R R
376 377 401 402 403
RS1/10S0R0J RS1/10S0R0J RS1/10S473J RS1/10S473J RS1/10S681J
R R R R R
111 112 113 131 132
RS1/16S223J RS1/16S181J RS1/16S181J RS1/10S104J RS1/10S222J
R R R R R
404 409 410 411 412
RS1/10S681J RS1/16S681J RS1/16S103J RS1/16S681J RS1/16S681J
R R R R R
133 134 135 136 151
RS1/10S103J RS1/10S561J RS1/10S223J RS1/10S473J RS1/10S0R0J
R R R R R
413 414 415 416 417
RS1/16S681J RS1/16S473J RS1/16S472J RS1/16S473J RS1/16S473J
R R R R R
152 161 162 163 164
RS1/10S0R0J RS1/16S272J RS1/16S272J RS1/16S162J RS1/16S162J
R R R R R
418 419 420 423 424
RS1/10S473J RS1/10S222J RS1/10S222J RS1/10S0R0J RS1/16S393J
R R R R R
208 209 210 241 242
RS1/16S102J RS1/16S102J RS1/16S102J RS1/10S102J RS1/10S102J
R R R R R
431 501 502 503 507
RS1/8S151J See Contrast table See Contrast table See Contrast table See Contrast table
R R R R R
251 252 253 254 255
RS1/10S472J RS1/10S472J RS1/10S472J RS1/10S472J RS1/10S223J
R R R R R
508 511 512 513 514
See Contrast table See Contrast table See Contrast table See Contrast table See Contrast table
R R R R R
256 257 258 259 260
RS1/10S223J RS1/10S331J RS1/10S331J RS1/10S331J RS1/10S331J
R R R R R
518 591 592 601 602
See Contrast table RS1/16S473J RS1/16S102J RS1/16S473J RS1/16S472J
R R R R R
261 262 263 283 284
RN1/10SE4702D RN1/10SE4702D RS1/10S102J RS1/10S203J See Contrast table
R R R R R
603 604 605 606 607
RS1/16S221J RS1/16S682J RS1/16S221J RS1/16S682J RS1/16S102J
R R R R R
291 301 302 303 304
RD1/4PU911J RS1/10S103J RS1/10S103J RS1/10S103J RS1/10S331J
R R R R R
608 609 610 611 612
RS1/16S102J RS1/16S473J RS1/16S473J RS1/16S473J RS1/16S221J
45
DEH-P900R,P9050
=====Circuit Symbol and No.===Part Name --- -----------------------------------------------
Part No. -------------------------
=====Circuit Symbol and No.===Part Name --- -----------------------------------------------
Part No. -------------------------
R R R R R
613 614 615 616 617
RS1/16S682J RS1/16S221J RS1/16S682J RS1/16S221J RS1/16S473J
R R R R R
914 921 922 923 924
RS1/10S1R0J RS1/10S1R0J RD1/4PU221J RS1/10S102J RS1/4S152J
R R R R R
618 619 620 623 627
RS1/16S221J RS1/16S682J RS1/16S473J RS1/16S473J RS1/16S473J
R R R R R
926 931 932 933 934
RS1/10S223J RS1/10S472J RS1/10S473J RS1/10S103J RS1/10S473J
R R R R R
628 633 634 637 641
RS1/16S473J RS1/10S0R0J RS1/10S102J RS1/16S473J RS1/10S202J
R R R R R
935 936 941 942 943
RS1/10S103J RS1/10S103J RS1/10S472J RS1/4S221J RS1/4S221J
R R R R R
642 651 652 653 658
RS1/10S102J RS1/10S0R0J RS1/10S0R0J RS1/10S0R0J RS1/16S473J
R R R R R
951 952 953 954 962
RS1/8S153J RS1/10S472J RS1/10S472J RS1/16S102J RS1/10S102J
R R R R R
681 682 683 684 685
RS1/8S102J RS1/8S102J RS1/8S102J See Contrast table RS1/10S103J
R R R R R
963 964 971 972 973
RS1/10S473J RS1/10S822J RS1/10S102J RD1/4PU102J RS1/10S473J
R R R R R
686 687 688 689 690
RS1/10S103J RS1/10S223J RS1/10S223J RS1/10S223J RS1/10S272J
R R R R R
981 982 983 984 985
RS1/16S223J RS1/10S473J RS1/10S103J RS1/10S473J RS1/10S102J
R R R R R
691 692 693 694 695
RS1/10S223J RS1/10S272J RS1/10S223J RS1/10S272J RS1/16S473J
R R R R
986 989 991 992
RS1/10S224J RS1/10S473J RD1/4PU221J RS1/10S221J
R R R R R
696 697 698 699 700
RS1/16S473J RS1/16S473J RS1/8S471J RS1/10S102J RS1/10S103J
R R R R R
801 802 803 804 805
RS1/8S222J RS1/8S222J RS1/8S222J RS1/8S103J RS1/8S472J
R R R R R
806 807 809 810 811
RS2PMF220J RS1/8S221J RS1/10S103J RS1/10S222J RD1/4PU102J
R R R R R
812 813 814 818 819
RS1/10S152J RS1/4S221J RD1/4PU391J RS1/10S103J RS1/8S221J
R R R R R
820 821 851 852 853
RS1/10S1R0J RS1/10S1R0J RD1/4PU271J RS1/10S102J RS1/10S102J
R R R R R
862 864 911 912 913
RS1/10S102J RS1/10S102J RS1/10S0R0J RS1/10S152J RS1/10S512J
CAPACITORS
46
C C C C C
101 102 131 132 141
CKSQYB104K16 CKSQYB104K16 CKSQYB681K50 CEJA101M10 CCSQCH101J50
C C C C C
161 162 171 172 173
CKSQYB183K25 CKSQYB183K25 CEJA470M16 CKSQYB104K16 CEJA100M16
C C C C C
201 205 206 207 208
CKSYB105K16 CKSYB224K16 CKSYB224K16 CKSYB105K16 CKSYB105K16
C C C C C
209 210 211 212 213
CKSYB105K16 CKSYB105K16 CEJANP4R7M16 CEJANP4R7M16 CEJANP4R7M16
C C C C C
214 215 216 217 218
CEJANP4R7M16 CKSQYB473K50 CKSQYB473K50 CKSQYB473K50 CKSQYB473K50
C C C C C
219 220 221 222 223
CKSYB105K16 CKSYB105K16 CKSYB105K16 CKSYB105K16 CKSYB105K16
DEH-P900R,P9050
=====Circuit Symbol and No.===Part Name --- -----------------------------------------------
Part No. -------------------------
=====Circuit Symbol and No.===Part Name --- -----------------------------------------------
Part No. -------------------------
C C C C C
224 225 226 227 228
CKSYB105K16 CKSQYB333K50 CKSQYB123K50 CKSQYB473K50 CKSQYB153K50
C C C C C
503 504 505 506 507
See Contrast table See Contrast table See Contrast table See Contrast table See Contrast table
C C C C C
229 241 242 251 252
CKSQYB153K50 CKSQYB152K50 CKSQYB152K50 CEJA4R7M35 CEJA4R7M35
C C C C C
508 509 511 512 601
See Contrast table See Contrast table See Contrast table See Contrast table CEJA4R7M35
C C C C C
253 254 255 256 257
CEJA100M16 CEJA100M16 CKSQYB104K16 CKSQYB104K16 CEJA100M16
C C C C C
602 603 604 605 651
CKSQYB103K50 CCSQCH101J50 CCSQCH150J50 CCSQCH220J50 CKSYB225K16
C C C C C
258 259 260 261 262
CEJA100M16 CKSQYB103K50 CKSQYB103K50 CKSQYB103K50 CKSYB475K10
C C C C C
681 682 683 684 685
See Contrast table See Contrast table CKSQYB103K50 CKSQYB103K50 CKSQYB103K50
C C C C C
263 277 278 279 280
CEJANP100M10 CEJA4R7M35 CEJA101M16 CEJA100M16 CEJA100M16
C C C C C
686 801 802 803 804
CKSQYB473K16 CKSYB475K10 CKSQYB104K16 CEJA470M10 CKSQYB103K50
C C C C C
281 282 283 284 285
CKSYB225K16 CEJA330M25 CEJA330M25 See Contrast table See Contrast table
C C C C C
805 806 807 808 809
CEJA470M10 CKSQYB103K50 CKSQYB102K50 CKSYB221K50 CKSYB103K50
C C C C C
286 287 291 292 293
CASAQ3R3M16 CKSYB684K25 CKSYB225K16 CKSQYB103K50 CKSQYB103K50
C C C C C
810 811 812 813 814
CKSYB475K10 CKSYB225K16 CCSCH101J50 CKSQYB103K50 CKSQYB105K10
C C C C C
301 302 303 304 306
CKSQYB224K16 CKSQYB224K16 CKSQYB224K16 CKSQYB224K16 CEJA330M10
C C C C C
851 852 853 855 856
CKSQYB103K50 CKSYB104K16 CEJA220M16 CKSQYB102K50 CCSQCH101J50
C C C C C
307 309 310 311 351
CCH1339 CKSQYB104K16 CEJA100M16 CKSYB105K16 CEJA100M35
C C C C C
857 901 911 912 913
CCSQCH101J50 CKSYB103K50 CCH1183 CKSQYB472K50 CKSQYB103K50
C C C C C
352 353 354 355 356
CEJA100M35 CEJA100M35 CEJA100M35 CEJA100M35 CEJA100M35
C C C C C
914 915 921 922 923
C C C C C
357 358 359 360 361
CKSRYB222K50 CKSRYB222K50 CKSRYB222K50 CKSRYB222K50 CKSRYB222K50
C C C C C
931 951 961 962 963
CKSYB105K16 CKSYB103K50 CKSQYB102K50 CKSQYB104K16 CEJA2R2M50
C C C C C
362 403 404 405 406
CKSRYB222K50 CKSQYB473K16 CEJA101M10 CKSQYB103K50 CEJA220M10
C C C C C
971 972 973 975 981
CEJA101M16 CEJA100M16 CKSQYB103K50 CKSQYB102K50 CEJA220M16
C C C C C
407 408 409 411 413
CKSQYB103K50 CKSQYB223K50 CKSQYB223K50 CKSRYB472K50 See Contrast table
C C C
991 992 993
CKSQYB473K50 CKSQYB102K50 CEJA101M10
C C C C C
431 432 433 435 502
CEJA101M16 CKSQYB104K16 See Contrast table CCSQCH101J50 See Contrast table
470µF/16
470µF/16V
470µF/16V 330µF/10V
CEJA470M10 CCH1183 CCH1181 CKSQYB103K50 CEJA101M16
47
DEH-P900R,P9050
CONTRAST TABLE of TUNER AMP UNIT DEH-P900R/UC and DEH-P9050/ES are constructed same except for the following: Part No. Symbol and Description IC501 IC IC601 IC IC681 IC Q501 Transistor D271 Diode
DEH-P900R/UC PM4009A PD5483A TPD1018F DTA124EK 1SS396
DEH-P9050/ES Not used PD5484A Not used Not used Not used
D681,682 L501 L502 X501 R284
ERA15-02VH CTF1295 CTF1420 CSS1447 Not used
Not used Not used Not used Not used RS1/10S0R0J
R501,502,503,511 R507 R508,512 R513 R514
RS1/16S102J RS1/10S0R0J RS1/16S0R0J RS1/16S225J RS1/10S0R0J
Not used Not used Not used Not used Not used
R518 R684 C284,285 C413,511 C433
RS1/16S681J RS1/10S103J CEJA330M25 CKSQYB103K50 Not used
Not used Not used Not used Not used CCSQCH101J50
C502 C503,504 C505 C506,507 C508
CCSQCH101J50 CCSQCH270J50 CKSQYB104K16 CKSQYB471K50 CKSQYB104K16
Not used Not used Not used Not used Not used
C509 C512 C681,682
CEJA220M6R3 CCSRCH101J50 CKSQYB473K50
Not used Not used Not used
48
Diode Inductor Inductor Crystal Resonator 3.648MHz
DEH-P900R,P9050
=====Circuit Symbol and No.===Part Name --- -----------------------------------------------
B
Part No. -------------------------
Unit Number : CWE1501 Unit Name : FM/AM Tuner Unit
MISCELLANEOUS IC IC IC Q Q
1 2 3 1 2
IC IC IC Transistor Transistor
PML002A PM4008A BR9010FV 2SC4081 DTC124EU
Q Q Q Q Q
3 51 201 202 204
FET Transistor FET Transistor Transistor
3SK263 2SC4081 2SK932 DTC124EU 2SC4081
D D D D D
1 2 6 201 202
Diode Diode Diode Diode Diode
KV1410(23) 1SV248 KV1410(23) MA143 MA147
D D L L L
903 904 1 3 4
Diode Diode Coil Inductor Coil
KV1410(23) SVC253 CTC1155 LCTB1R5K2125 CTC1155
L L L L L
201 202 203 901 902
Inductor Inductor Inductor Coil Inductor
LCTB330K1608 CTF1287 LCTA121J3225 CTC1154 LCTA3R3J3225
L L T CF CF
904 905 51 51 52
Inductor Inductor Coil Ceramic Filter Ceramic Filter
LCTBR47K1608 LCTBR47K1608 CTE1132 CTF1442 CTF1442
CF CF X
53 202 901
Ceramic Filter Ceramic Filter Crystal Resonator 10.250MHz
CTF1442 CTF1476 CSS1432
RESISTORS R R R R R
1 2 5 7 8
RS1/16S183J RS1/16S103J RS1/16S0R0J RS1/16S273J RS1/16S473J
R R R R R
9 10 11 12 13
RS1/16S223J RS1/16S473J RS1/16S221J RS1/16S103J RS1/16S104J
R R R R R
16 17 18 19 20
RS1/16S223J RS1/16S221J RS1/16S221J RS1/16S473J RS1/16S470J
R R R R R
31 51 52 53 54
RS1/16S0R0J RS1/16S470J RS1/16S103J RS1/16S103J RS1/16S331J
R R R R R
55 56 57 58 59
RS1/16S331J RS1/16S560J RS1/16S560J RS1/16S102J RS1/16S225J
R R R R R
60 61 101 102 103
RS1/16S133J RS1/16S433J RS1/16S333J RS1/16S103J RS1/16S333J
=====Circuit Symbol and No.===Part Name --- -----------------------------------------------
Part No. -------------------------
R R R R R
104 106 108 110 111
RS1/16S562J RS1/16S0R0J RS1/16S0R0J RS1/16S154J RS1/16S273J
R R R R R
113 114 115 116 202
RS1/16S222J RS1/16S333J RS1/16S334J RS1/16S473J RS1/16S472J
R R R R R
203 204 205 206 208
RS1/16S225J RS1/16S102J RS1/16S220J RS1/16S471J RS1/16S104J
R R R R R
209 210 213 902 904
RS1/16S104J RS1/16S563J RS1/16S223J RS1/16S103J RS1/16S473J
R R R R
907 908 909 914
RS1/16S103J RS1/16S681J RS1/16S473J RS1/16S562J
CAPACITORS C C C C C
1 6 8 10 11
CCSQCH4R0C50 CKSQYB105K10 CKSRYB222K50 CCSRCH220J50 CCSRCH150J50
C C C C C
12 14 15 16 17
CCSRCH8R0D50 CCSRCJ3R0C50 CKSRYB103K50 CKSRYB222K50 CKSRYB222K50
C C C C C
18 19 20 21 24
CCSRCJ3R0C50 CKSRYB103K50 CKSRYB103K50 CKSRYB103K50 CKSQYB334K16
C C C C C
26 30 32 35 51
CKSRYB472K50 CCSRCH220J50 CCSRCH470J50 CKSRYB103K50 CKSRYB103K50
C C C C C
52 53 54 55 56
CKSRYB473K16 CCSRCK2R0C50 CKSRYB103K50 CKSRYB104K16 CKSRYB104K16
C C C C C
58 101 102 103 105
CKSQYB224K16 CEALNP100M10 CCSRCH151J50 CKSRYB473K16 CKSRYB682K25
C C C C C
106 107 108 109 110
CEALR68M50 CKSRYB103K50 CKSQYB474K16 CKSQYB474K16 CKSRYB104K16
C C C C C
111 112 113 114 115
CKSRYB104K16 CKSRYB104K16 CKSRYB123K25 CEAL220M6R3 CKSRYB473K16
49
DEH-P900R,P9050
=====Circuit Symbol and No.===Part Name --- -----------------------------------------------
Part No. -------------------------
=====Circuit Symbol and No.===Part Name --- -----------------------------------------------
Part No. -------------------------
C C C C C
116 117 120 121 122
CEAL2R2M50 CKSRYB102K50 CKSRYB183K25 CKSRYB332K50 CKSRYB562K25
L L L L L
1904 1905 1906 1907 1908
Inductor Inductor Array Inductor Array Inductor Inductor
LCTA220J2520 CTF1421 CTF1421 CTF1295 CTF1295
C C C C C
123 125 126 127 128
CKSRYB681K50 CKSRYB103K50 CKSRYB103K50 CEAL2R2M50 CKSRYB103K50
X S S S S
1901 1901 1902 1903 1904
Ceramic Resonator 15.62MHz Push Switch Push Switch Push Switch Push Switch
CSS1458 CSG1112 CSG1112 CSG1111 CSG1111
C C C C C
201 202 203 204 205
CCSRCH471J50 CCSRCH100D50 CKSRYB104K16 CKSRYB332K50 CKSRYB103K50
S S S S S
1905 1906 1907 1908 1909
Push Switch Push Switch Push Switch Push Switch Push Switch
CSG1112 CSG1112 CSG1112 CSG1112 CSG1112
C C C C C
206 207 208 209 210
CKSRYB104K16 CKSRYB473K16 CCSRCH560J50 CEAL470M6R3 CKSRYB103K50
S S S S S
1910 1911 1912 1913 1914
Push Switch Push Switch Push Switch Push Switch Push Switch
CSG1112 CSG1112 CSG1112 CSG1112 CSG1112
C C C C C
211 212 215 216 217
CKSRYB103K50 CCSRCH101J50 CKSRYB223K25 CKSQYB334K16 CKSRYB103K50
S S S S S
1915 1916 1917 1918 1919
Push Switch Push Switch Push Switch Push Switch Push Switch
CSG1112 CSG1112 CSG1112 CSG1112 CSG1112
C C C C C
219 220 221 222 223
CKSQYB105K10 CKSRYB104K16 CKSRYB473K16 CKSQYB334K16 CKSQYB474K16
S S S S S
1920 1921 1922 1923 1924
Push Switch Push Switch Push Switch Push Switch Push Switch
CSG1112 CSG1112 CSG1112 CSG1112 CSG1112
C C C C C
224 225 226 902 904
CKSRYB104K16 CKSRYB272K50 CKSRYB682K25 CCSRCH270J50 CKSRYB223K25
S
1925
Push Switch
CSG1111
C C C C C
905 906 907 909 910
CKSRYB103K50 CCSRTH100D50 CCSRTH150J50 CCSRTH100D50 CKSRYB332K50
C C C C C
912 913 914 915 916
CKSQYB474K16 CKSRYB223K25 CKSRYB682K25 CKSQYB223K25 CKSQYB474K16
C C C C C
917 918 919 920 921
CKSYB475K10 CKSRYB223K25 CKSQYB225K10 CCSRCH270J50 CCSRCH270J50
C C
922 923
CKSYB105K16 CKSRYB103K50
C
Unit Number : CWM6226 Unit Name : Keyboard Unit
MISCELLANEOUS IC IC IC D D
1901 1902 1903 1901 1902
IC IC HIC Module Diode Network Diode Network
PD5471A PD8051A RS-140 DA204U DA204U
D D L L L
1904 1905 1901 1902 1903
Diode LED Chip Inductor Chip Inductor Inductor
MA110 CL170UBX LCTA2R2J3225 LCTA2R2J3225 CTF1484
50
RESISTORS R R R R R
1901 1902 1903 1904 1905
RS1/16S154J RS1/16S473J RA4C101J RA3C101J RA3C101J
R R R R R
1906 1907 1908 1909 1910
RA4C101J RS1/16S473J RA3C101J RA3C101J RA4C101J
R R R R R
1911 1912 1913 1914 1915
RA4C101J RA4C101J RA3C101J RA4C101J RA4C101J
R R R R R
1922 1923 1924 1925 1930
RS1/10S121J RS1/10S2R2J RS1/8S222J RS1/8S222J RS1/16S472J
R R R R R
1931 1956 1957 1958 1959
RS1/16S473J RS1/10S0R0J RS1/10S0R0J RS1/10S0R0J RS1/10S0R0J
R R R R R
1960 1961 1962 1963 1964
RS1/8S911J RS1/8S911J RS1/10S511J RS1/10S511J RS1/10S511J
R R R R R
1965 1966 1967 1968 1969
RS1/10S511J RS1/8S511J RS1/8S511J RS1/8S511J RS1/8S511J
DEH-P900R,P9050
=====Circuit Symbol and No.===Part Name --- -----------------------------------------------
Part No. -------------------------
=====Circuit Symbol and No.===Part Name --- -----------------------------------------------
Part No. -------------------------
R R R R R
1970 1971 1972 1973 1974
RS1/8S511J RS1/8S511J RS1/8S511J RS1/8S511J RS1/8S751J
R R R R R
3034 3038 3039 3040 3041
RS1/16S102J RS1/16S102J RS1/16S102J RS1/16S102J RS1/16S102J
R R R
1975 1976 1977
RS1/8S751J RS1/8S751J RS1/8S751J
R R R R R
3042 3043 3044 3045 3047
RS1/16S102J RS1/16S102J RS1/16S102J RS1/16S473J RS1/16S473J
CAPACITORS C C C C C
1901 1902 1903 1904 1906
CKSQYB105K10 CKSRYB103K25 CSZS100M6R3 CSZS100M6R3 CKSQYB103K25
R R R R R
3048 3049 3101 3102 3103
RS1/16S473J RS1/16S473J RS1/16S0R0J RS1/16S0R0J RS1/16S471J
C C C C C
1907 1908 1911 1914 1916
CSZS100M6R3 CKSRYB473K16 CKSRYB473K16 CKSRYB103K25 CKSQYB104K25
R R R R R
3104 3105 3106 3107 3108
RS1/16S473J RS1/16S473J RS1/16S105J RS1/16S102J RS1/16S102J
C C C
1917 1918 1919
CSZSR100M16 CKSRYB102K50 CCSQCH221J50
R R R R R
3109 3110 3201 3202 3203
RS1/16S102J RS1/16S0R0J RS1/16S332J RS1/16S391J RS1/16S101J
R R R R R
3204 3301 3302 3303 3304
RS1/16S271J RS1/16S273J RS1/16S273J RS1/16S512J RS1/16S512J
R R R
3305 3306 3307
RS1/16S272J RS1/16S272J RS1/16S681J
D
Unit Number : CWX2323 Unit Name : DSP Unit
MISCELLANEOUS IC IC IC IC IC
3001 3101 3201 3202 3203
IC IC IC IC IC
PD5504A AK7714 TC74HC393AF TC9246F HD74HCT126FP
IC D L L L
3301 3301 3001 3101 3201
IC Diode High Loss Inductor High Loss Inductor High Loss Inductor
NJM4580M MA8043(L) CTF1410 CTF1410 CTF1410
L L L L L
3202 3203 3301 3302 3303
Inductor High Loss Inductor High Loss Inductor High Loss Inductor High Loss Inductor
LCTB2R2K1608 CTF1410 CTF1410 CTF1410 CTF1410
L L L L L
3304 3305 3306 3307 3308
High Loss Inductor High Loss Inductor High Loss Inductor High Loss Inductor High Loss Inductor
CTF1410 CTF1410 CTF1410 CTF1410 CTF1410
L L X X
3309 3310 3001 3101
High Loss Inductor High Loss Inductor Radiator 10.00MHz Crystal Resonator 22.5792MHz
CTF1410 CTF1410 CSS1428 CSS1403
RESISTORS R R R R R
3001 3004 3010 3011 3012
RA4C102J RS1/16S102J RS1/16S681J RS1/16S102J RS1/16S102J
R R R R R
3013 3014 3018 3023 3024
RS1/16S102J RS1/16S102J RS1/16S102J RA3C221J RS1/16S102J
R R R R R
3025 3026 3028 3029 3033
RA3C102J RA4C681J RS1/16S473J RS1/16S473J RS1/16S102J
CAPACITORS C C C C C
3001 3101 3102 3103 3104
CKSRYB103K50 CCSRCH180J50 CCSRCH180J50 CKSQYB103K50 CKSYB106K6R3
C C C C C
3105 3106 3107 3108 3201
CKSRYB104K16 CKSRYB104K16 CKSRYB104K16 CKSRYB104K16 CKSRYB103K50
C C C C C
3202 3203 3204 3205 3206
CKSQYB474K16 CKSRYB103K50 CKSRYB123K25 CKSRYB103K50 CKSRYB103K50
C C C C C
3207 3208 3301 3302 3303
CCSRCH330J50 CKSYB106K6R3 CKSRYB332K50 CKSRYB332K50 CKSYB106K6R3
C C C C C
3304 3305 3306 3307 3308
CKSYB106K6R3 CKSYB106K6R3 CKSYB106K6R3 CKSYB225K16 CKSRYB104K16
C C C C C
3309 3310 3311 3312 3313
CKSYB106K6R3 CKSRYB104K16 CSZSR470M6R3 CKSRYB104K16 CKSYB106K6R3
C C
3314 3315
CKSRYB103K50 CKSQYB105K10
51
DEH-P900R,P9050
=====Circuit Symbol and No.===Part Name --- -----------------------------------------------
E
Part No. -------------------------
Unit Number : CWX2322 Unit Name : ASL Unit
MISCELLANEOUS IC IC Q D D
4501 4502 4501 4501 4502
D 4503 VR 4501 MIC4501
NJM2068MD NJM2068MD 2SC2458 MA152WK MA3043(LMH)
Diode Semi-fixed 10kΩ(B) Microphone
MA3075(M) CCP1319 CPM1011
R R R R R
4501 4502 4503 4504 4505
RS1/8S222J RS1/8S683J RS1/8S103J RS1/8S472J RS1/8S471J
R R R R R
4506 4507 4508 4509 4510
RS1/8S682J RS1/8S684J RS1/8S562J RS1/8S391J RS1/8S472J
R R R R R
4511 4512 4513 4514 4515
RS1/8S472J RS1/8S472J RS1/8S153J RS1/8S153J RS1/8S102J
R
4517
RS1/8S270J
CAPACITORS C C C C C
4501 4502 4503 4504 4505
CEJA470M10 CEJA470M10 CEJAR68M50 CEJA100M16 CEJA470M10
C C C C C
4506 4507 4508 4509 4510
CEJA470M16 CEJA100M16 CEJANP220M10 CEJAR68M50 CEJANP100M10
C C C
4511 4512 4513
CKSYB823K50 CCSCH101J50 CEJA470M10
S S
H
Unit Number : Unit Name : Switch PCB 951 952
Switch(CLOSE) Switch(OPEN)
X S S
CSS1453 CSN1051 CSN1052
901 801 802
Radiator 8.380MHz Spring Switch(HOME) Spring Switch(CLAMP)
R R R R R
101 102 103 201 205
RS1/8S120J RS1/8S100J RS1/16S222J RS1/16S104J RS1/16S103J
R R R R R
206 207 208 210 212
RS1/16S393J RS1/16S182J RS1/16S304J RS1/16S0R0J RS1/16S103J
R R R R R
213 214 215 216 217
RS1/16S103J RS1/16S123J RS1/16S273J RS1/16S273J RS1/16S681J
R R R R R
218 309 310 501 502
RS1/16S681J RS1/16S473J RS1/16S473J RS1/16S102J RS1/16S681J
R R R R R
503 504 505 506 507
RS1/16S681J RS1/16S681J RS1/16S681J RS1/16S681J RS1/16S0R0J
R R R R R
511 512 605 801 802
RS1/16S0R0J RS1/16S512J RA4C0R0J RS1/8S751J RS1/8S751J
R R R R R
901 902 903 904 905
RS1/16S222J RS1/16S473J RS1/16S222J RS1/16S473J RN1/16SE1502D
R R R R R
907 908 909 910 911
RS1/16S473J RS1/16S222J RS1/16S104J RS1/16S103J RS1/16S223J
R R
912 917
RS1/16S473J RS1/16S0R0J
CAPACITORS CSN1012 CSN1022
Unit Number : CWX2359 Unit Name : Control Unit
MISCELLANEOUS IC IC IC IC IC
201 301 601 701 901
IC IC IC IC IC
UPD63710GC BA5985FM PD0236AM BA05SFP PE5011C
Q Q D D TH
101 901 801 802 901
Transistor Transistor LED LED Thermistor
2SB1132 UN2111 CL200IRX CL200IRX CCX1037
52
Part No. -------------------------
RESISTORS
IC IC Transistor Diode Diode
RESISTORS
F
=====Circuit Symbol and No.===Part Name --- -----------------------------------------------
C C C C C
101 102 103 104 105
CCSRCH102J25 CKSQYB104K16 CEV101M6R3 CEV470M6R3 CKSQYB334K16
C C C C C
106 107 201 202 203
CKSQYB334K16 CKSQYB334K16 CKSQYB104K16 CEV101M6R3 CKSQYB104K16
C C C C C
204 205 206 207 208
CKSRYB332K50 CKSQYB104K16 CKSRYB392K50 CKSQYB224K16 CCSRCH270J50
C C C C C
209 210 211 212 213
CCSRCJ3R0C50 CCSRCH221J50 CCSRCH101J50 CKSRYB682K25 CKSQYB104K16
DEH-P900R,P9050
=====Circuit Symbol and No.===Part Name --- -----------------------------------------------
Part No. -------------------------
C C C C C
214 215 216 217 218
CKSRYB104K16 CKSQYB104K16 CKSRYB104K16 CKSRYB104K16 CKSRYB104K16
C C C C C
219 220 223 301 501
CKSRYB104K16 CKSRYB104K16 CKSQYB471K50 CEV101M10 CKSRYB221K50
C C C C C
611 701 702 703 801
CKSRYB104K16 CEV101M6R3 CCH1300 CKSQYB334K16 CKSRYB103K25
C C C C
802 901 902 903
I Q Q
22µF/6.3V
CKSRYB103K25 CKSRYB472K50 CKSYB475K10 CKSRYB103K25
Unit Number : Unit Name : Photo Unit 1 2
Photo-transistor Photo-transistor
CPT230SX-TU CPT230SX-TU
Miscellaneous Parts List M M M M
1 2 3 951
Pickup Unit(Service)(P8) Motor Unit(CARRIAGE) Motor Unit(LOADING) Motor Unit(SPINDLE) Motor (AUTO FLAP)
CXX1285 CXB2190 CXB2195 CXB2562 CXM1085
53
DEH-P900R,P9050
6. ADJUSTMENT 6.1 CD ADJUSTMENT 1) Precautions • This unit uses a single power supply (+5V) for the regulator. The signal reference potential, therefore, is connected to REFO(approx. 2.5V) instead of GND. If REFO and GND are connected to each other by mistake during adjustments, not only will it be impossible to measure the potential correctly, but the servo will malfunction and a severe shock will be applied to the pick-up. To avoid this, take special note of the following. Do not connect the negative probe of the measuring equipment to REFO and GND together. It is especially important not to connect the channel 1 negative probe of the oscilloscope to REFO with the channel 2 negative probe connected to GND. Since the frame of the measuring instrument is usually at the same potential as the negative probe, change the frame of the measuring instrument to floating status. If by accident REFO comes in contact with GND, immediately switch the regulator or power OFF. • Always make sure the regulator is OFF when connecting and disconnecting the various filters and wiring required for measurements. • Before proceeding to further adjustments and measurements after switching regulator ON, let the player run for about one minute to allow the circuits to stabilize. • Since the protective systems in the unit's software are rendered inoperative in test mode, be very careful to avoid mechanical and /or electrical shocks to the system when making adjustment. • Disc detection during loading and eject operations is performed by means of a photo transistor in this unit.Consequently, if the inside of the unit is exposed to a strong light source when the outer casing is removed for repairs or adjustment, the following malfunctions may occur. *During PLAY, even if the eject button is pressed,the disc will not be ejected and the unit will remain in the PLAY mode. *The unit will not load a disc. When the unit malfunctions this way, either re-position the light source, move the unit or cover the photo transistor.
54
2) Test Mode This mode is used for adjusting the CD mechanism module of the device. • Test mode starting procedure Reset while pressing the 4 and 6 keys together. • Test mode cancellation Switch ACC, back-up OFF. • After pressing the EJECT key, do not press any other key until the disk is completely ejected. • If the ] or [ key is pressed while focus search is in progress, immediately turn the power off (otherwise the actuator may be damaged due to adhesion of the lenses). • Jump operation of TRs other than 100TR continues after releasing the key. CRG move and 100TR jump operations are brought into the “Tracking close” status when the key is released. • Powering Off/On resets the jump mode to “Single TR (91)”, the RF AMP gain setting to 0 dB, and the automatic adjustment value to the initial value.
DEH-P900R,P9050
- Flow Chart 4
6 Test Mode In Reset
SOURCE
Sourse CD
New test mode
BAND
TRK
MIN
Power ON (Not adjustment for T.Offset)
SEC
00 00 00
Display
2
3
6 *1
Power ON (Adjustment for T.Offset)
TRK
Display
MIN
SEC
RF AMP Gain Select TRK
99 99 99
MIN
SEC
GG GG GG
Power OFF
BAND
3 Focus Close/ S Curve Check
TRK
MIN
SEC
TRK
Display
MIN
[ *8
*2
Focus Mode Select
91 91 91
Display
]
1
6
TRK
SEC
0x 0x 0x
MIN
SEC
TRK
MIN
MIN
SEC
TRK
MIN
TRK
99 99 99
MIN
SEC
00 00 00
or SEC
*3 Auto Adjustment Display Select
CRG-
00 00 00
or TRK
*8
CRG+
00 00 00
2
or SEC
TRK
99 99 99
MIN
SEC
99 99 99
Power OFF
3
]
[
2
RF AGC Coefficient Display/ Rough Servo and RF AGC
CRG+
CRG-
T.Balance Adjustment
6
1
BAND T.Close and F,T AGC and RF AGC and Fit Servo
T. Close and Fit Servo
TRK
Display
MIN
TRK
SEC
MIN
or
or TRK
MIN
SEC
8x 8x 8x
8x 8x 8x
TRK
SEC
MIN
SEC
9x 9x 9x
9x 9x 9x
Tracking Open
Power OFF
*7
*5
F, T, RF AGC/ F.Bias Display Select
F, T AGC and RF AGC
[
]
6
3
1
BAND
CRG/TR Jump NO. Select
2
*4 CRG-/TR Jump- *4 CRG+/TR Jump+
*6 TRK
Power OFF
Display
TRK
2
+6dB 06 06 06
+12dB 12 12 12
TRK
Display
*2 Display
*3
Focus Close 00 00 00 (99 99 99)
F.Offset Display
SEC
SEC
8x 8x 8x or
S Curve Check 01 01 01
RF.Offset Display
MIN
MIN
9x 9x 9x
Tracking Open
TYP Display
SEC
or
BAND
*1
MIN
8x 8x 8x
TRK
MIN
SEC
9x 9x 9x F.Cansel Display
F.Cancel Value = {Top Rank 8bit of Set Value (7F [H] to 80 [H] ) + 128} / 4 = 63 [D] to (32 [D] ) to 00 [D] *4 Single TR/32TR/100TR *5
Single TR Display 9x(8x):91(81)
32TRK 92(82)
100TRK 93(83)
CRG Move 94(84)
*6 CRG Move, 100TR Jump Only *7
TRK, MIN, SEC
F.AGC Gain
T.AGC Gain
RF AGC Gain
(F,T.AGC Gain = (Present Value/Initial Value) ¥ 20) *8 Voltage of CRG Motor = 2 [V]
55
DEH-P900R,P9050
6.2 CHECKING THE GRATING AFTER CHANGING THE PICKUP UNIT • Note : The grating angle of the PU unit cannot be adjusted after the PU unit is changed. The PU unit in the CD mechanism module is adjusted on the production line to match the CD mechanism module and is thus the best adjusted PU unit for the CD mechanism module. Changing the PU unit is thus best considered as a last resort. However, if the PU unit must be changed, the grating should be checked using the procedure below.
• Purpose : To check that the grating is within an acceptable range when the PU unit is changed. • Symptoms of Mal-adjustment : If the grating is off by a large amount symptoms such as being unable to close tracking, being unable to perform track search operations, or taking a long time for track searching. • Method : • Measuring Equipment • Measuring Points • Disc • Mode
• Oscilloscope, Two L.P.F. • E, F, REFO • ABEX TCD-784 • TEST MODE CONTROL UNIT
E F
L.P.F. E
REFO
Xch 100kΩ 390pF
REFO
F
Ych
Oscilloscope
100kΩ 390pF
REFO L.P.F.
• Checking Procedure 1. In test mode, load the disc and switch the 5V regulator on. 2. Using the ] and [ buttons, move the PU unit to the innermost track. 3. Press key 3 to close focus, the display should read "91". Press key 2 to implement the tracking balance adjustment the display should now read "81". Press key 3 2 times. The display will change, returning to "81" on the fourth press. 4. As shown in the diagram above, monitor the LPF outputs using the oscilloscope and check that the phase difference is within 75° . Refer to the photographs supplied to determine the phase angle. 5. If the phase difference is determined to be greater than 75° try changing the PU unit to see if there is any improvement. If, after trying this a number of times, the grating angle does not become less than 75° then the mechanism should be judged to be at fault. • Note Because of eccentricity in the disc and a slight misalignment of the clamping center the grating waveform may be seen to "wobble" ( the phase difference changes as the disc rotates). The angle specified above indicates the average angle. • Hint Reloading the disc changes the clamp position and may decrease the "wobble".
56
DEH-P900R,P9050
Grating waveform
Ech → Xch 20mV/div, AC Fch → Ych 20mV/div, AC
0°
30°
45°
60°
75°
90°
57
DEH-P900R,P9050
7. GENERAL INFORMATION 7.1 DIAGNOSIS 7.1.1 TEST MODE - Error Messages If a CD is not operative or stopped during operation due to an error, the error mode is turned on and cause(s) of the error is indicated with a corresponding number. This arrangement is intended at reducing nonsense calls from the users and also for facilitating trouble analysis and repair work in servicing. (1) Basic Indication Method 1) When SERRORM is selected for the CSMOD (CD mode area for the system), error codes are written to DMIN (minutes display area) and DSEC (seconds display area). The same data is written to DMIN and DSEC. DTNO remains in blank as before. 2) Main unit display examples Depending on display capability of LCD used, display will vary as shown below. xx contains the error number. 8-digit display ERROR–xx
6-digit display ERR–xx OR Err–xx
4-digit display E–xx
(2) Error Code List Code Class Displayed error code Description of the code and potential cause(s) 10 Electricity Carriage Home NG CRG can't be moved to inner diameter. CRG can't be moved from inner diameter. → Failure on home switch or CRG move mechanism. 11
Electricity
Focus Servo NG
Focusing not available. → Stains on rear side of disc or excessive vibrations on REWRITABLE.
12
Electricity
Spindle Lock NG
Spindle not locked. Sub-code is strange (not readable). → Failure on spindle, stains or damages on disc, or excessive vibrations.
Subcode NG
A disc not containing CD-R data is found. Turned over disc are found, though rarely. → Failure on home switch or CRG move mechanism.
RF AMP NG
An appropriate RF AMP gain can't be determined. → CD signal error.
17
Electricity
Setup NG
APC protection doesn't work. Focus can be easily lost. → Damages or stains on disc, or excessive vibrations.
30
Electricity
Search Time Out
Failed to reach target address. → CRG tracking error or damages on disc.
A0
System
Power Supply NG
Power (VD) is ground faulted. → Failure on SW transistor or power supply (failure on connector).
Remarks: Mechanical errors are not displayed (because a CD is turned off in these errors). Unreadable TOC does not constitute an error. An intended operation continues in this case. A newly designed main unit must conform to the example given above. Upper digits of an error code are subdivided as shown below: 1x: Setup relevant errors, 3x: Search relevant errors, 3x: Search relevant errors, Ax: Other errors.
58
DEH-P900R,P9050
- New Test Mode S-CD plays the same way as before. If an error such as off focus, spindle unlocking, unreadable sub-code, or sound skipping occurs after setup, its cause and time occurred (in absolute time) are displayed. During setup, operational status of the control software (internal RAM: CPOINT) is displayed. These displays and functions are prepared for enhancing aging in the servicing and efficiency of trouble analysis. (1) Shifting to the New Test Mode 1 Turn on the current test mode by starting the reset from the key (it varies between the products). 2 Select S-CD for the source through the specified procedure including use of the [SOURCE] key, and inserting the disc. Then, press the [ 6 ] key while maintaining the regulator turned off. 3 After the above operations, the new test mode remains on irrespective of whether the S-CD is turned on or off. You can reset the new test mode by turning on the reset start. * With some products, the new test mode can be reset through the same operations as that employed for shifting to the STBY mode (while maintaining the Acc turned off). (2) Key Correspondence Key Test mode Power Off Power On BAND To power on To power off (offset adjustment performed)
In-play –
New test mode Error Production Time/Err.No. switching
]
–
FWD-Kick
FF/TR+
–
[
–
REV-Kick
REV/TR-
–
1
–
Scan
–
2
RF AMP gain switching
T.Close (AGC performed) /parameter display switching Parameter display switching /T.BAL adjustment/T.Open F.Close/RF AGC/F.T.AGC
Mode
–
3
To power on – – (offset adjustment not performed) 6 – F.Mode switching Auto/Manu T.No./Time switching /T.Close (no AGC)/Jump switching Note: Eject and CD on/off is performed in the same procedure as that for the normal mode. (3) Cause of Error and Error Code Code Class Contents 40 Electricity Off focus detected.
Description and cause FOK goes low. → Damages/stains on disc, vibrations or failure on servo.
41
Electricity
Spindle unlocked.
FOK = Low continued for 50 msec. → Damages/stains on disc, vibrations or failure on servo.
42
Electricity
Sub-code unreadable.
Sub-code was unreadable for 50 msec. → Damages/stains on disc, vibrations or failure on servo.
43
Electricity
Sound skipping detected.
Last address memory function was activated. → Damages/stains on disc, vibrations or failure on servo.
Note: Mechanical errors during aging are not displayed. The error codes should be indicated in the same way as in the normal mode.
59
DEH-P900R,P9050
(4) Display of Operational Status (CPOINT) during Setup Status No. Contents 00 CD+5V ON process in progress. 01 Servo LSI initialization (1/3) in progress. 02 Servo LSI CRAM initialization in progress. 03 Servo LSI initialization (2/3) in progress. 04 Offset adjustment (1/3) in progress. 05 Offset adjustment (2/3) in progress. 06 Offset adjustment (3/3) in progress. 07 FZD adjustment in progress. 08 Servo LSI initialization (3/3) in progress. 10 Carriage move to home position started. 11 Carriage move to home position started. 12 Carriage is moving toward inner diameter. 13
Carriage is moving toward outer diameter.
14 15 20 21 22 23 24 25
Carriage outer kick in progress. Carriage outer diameter feed (1 second) in progress. Servo close started. Pre-processing for focus search started. Spindle rotation and focus search started. Waiting for focus close (XSI=Low). Standing by after focus close is over. Focus search preprocessing is in progress while setup protection is turned on. Focus search preprocessing is in progress while focus recovery is turned on. Wait time after focus close is set up. Standing by after focus close is over. Setup (1/2) before T balance adjustment is started. Setup (2/2) before T balance adjustment is started. T balance adjustment started. T balance adjustment (1/2). T balance adjustment (2/2). Waiting for spindle rotation to end. Spindle rough servo. Standing by after spindle rough servo is over. RF AGC started. RF AGC started. RF AGC ending process in progress. Tracking close in progress. Standing by after tracking is closed. Carriage closing in progress. Focus/tracking AGC started. Focus AGC started. Focus AGC in progress. Tracking AGC in progress. Standing by after focus/tracking AGC are over. Spindle processes applicable servo. Check for servo close is started. Check of LOCK pin started. RF AGC started. RF AGC in progress. Standing by after RF AGC is over.
26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51
60
Protective action None None None None None None None None None None None Specified 10 seconds has been passed or failure on home switch. Specified 10 seconds has been passed or failure on home switch. None None None None None Specified focus search time has been passed. Specified focus search time has been passed. None None Off focus. Off focus. Off focus. Off focus. Off focus. Off focus. Off focus. Off focus. Off focus. Off focus. Off focus. Off focus. Off focus. Off focus. Off focus. Off focus. Off focus. Off focus. Off focus. Off focus. Off focus. Off focus or spindle not locked. Off focus. Off focus. Off focus.
DEH-P900R,P9050
(5) Display Examples 1) During Setup (When status no. = 11) TRK No. MIN. SEC. 11 11' 11" 2) During Operation (TOC read, TRK search, Play, FF and REV) The same as in the normal mode. 3) When a Protection Error Occurred Switch to the following displays (A) and (B) using the [BAND] switch: (A) Error occurrence timing display in absolute time. An example: Error occurred in 12th tune at 34'56" in absolute time. TRK No. 12
MIN. 34'
SEC. 56"
(B) Error No. display An example: Error #40 (Off focus is detected) ERROR-40
61
DEH-P900R,P9050
A
7.1.2 DISASSEMBLY
CD Mechanism Module
A
- Remove the Case (Not shown)
A
A
1. Remove the two screws, and then remove the Case.
- Remove the CD Mechanism Module 1. Remove the four screws A. 2. Disconnect the two connectors, and then remove the CD Mechanism Module.
- Remove the Tuner Amp Unit (1/2) A
1. Disconnect the three connectors. 2. Remove the four screws A. 3. Disconnect the two stoppers indicated by arrows, and then remove the Grille Assy.
A A Grille Assy
62
A
DEH-P900R,P9050
- Remove the Tuner Amp Unit (2/2)
Antenna Cable
1. Remove the screw A, four screws C, and then remove the Antenna Cable and Holder. 2. Remove the screw B. 3. Stretch the four tabs, and then remove the Tuner Amp Unit.
A
B
Holder
C
C C
C
Tuner Amp Unit
- Remove the DSP Unit 1. Remove the three solder of tabs indicated by arrows, and then remove the Case. 2. Disconnect the connector, and then remove the DSP Unit.
Case DSP Unit
63
DEH-P900R,P9050
- Removing the Upper Frame 1. Remove six Springs A, two Springs B and four Screws. 2. Remove two Tabs situated on rear side of the Upper Frame, remove two Arms on the front side, then remove two Tabs on the front side.
A Upper Frame A A
A
B
A
Arm
Arm B
- Removing the Carriage Mechanism
Carriage Mechanism Section
1. Disengage the Carriage Mechanism from the two dampers situated in the front side by driving it up, then disengage and remove the mechanism from the two dampers by driving it up aslant into front side direction. Note : When assembling the Carriage Mechanism, coat the dampers with alcohol prior to the assembly.
- Removing the Clamp Arm Assy
A
A
Clamp Arm Assy Section
1. Remove a Spring A, a B and a Spring C. 2. Drive the Clamp Arm Assy up into rear side direction, then disengage the arm from its current position Finally, drive the assembly approximately 45 degrees upward, then slide the assembly toward right side to remove it.
B
C
64
DEH-P900R,P9050
- Removing the Guide Arm Assy 1. Remove a connector, a spring A and B 2. Drive the Guide Arm Assy up aslant into rear side direction, then remove it from a Pin. Finally, drive the assembly approximately 45 degrees upward, then slide the assembly toward left side to remove it. Note : When assembling the guide arm assembly, route the cord inside the assembly. In this operation, care must be exercised so that cord may be caught by the gear.
Guide Arm Assy Section
A
B Pin
LO Arm Assy Section
- Removing the LO Arm Assy 1. Remove two Pins to dismount the LO Arm Assy.
- Removing the Control Unit and the Spindle
Short Pin
Motor 1. Remove from the connector after mounting the short pin on the flexible PCB of the pickup unit. 2. Remove two Soldered joints, then remove two Screws A. 3. Remove two connectors and a Screw B. 4. Disengage the Control Unit from two Tabs, then dismount the unit by sliding it toward left. 5. Dismount the Spindle Motor.
Spindle Motor
B
Control Unit
A
A
65
DEH-P900R,P9050
- Removing the Loading Motor and Carriage
C
Motor 1. Remove the Spring and two Screws A. 2. Dismount the Loading Motor. 3. Remove the Belt, a Screw B, two Screws C, a Guide and a Screw Unit. 4. Dismount the Carriage Motor. Note : When assembling the Belt, use care so that it may not be contaminated by grease.
Guide B Screw Unit
Carriage Motor
Belt
C
A
A
Loading Motor
- Removing the Pickup Unit 1. Remove two Screws and a Shaft. 2. Dismount the Pickup Unit.
Pickup Unit
Shaft
66
DEH-P900R,P9050
7.2 IC PML004AF PA2028A PAL005A S-81250SGUP PM4009A
PD5483A, PD5484A BA6288FS BR9010FV PD5471A PD8051A
PD5504A AK7714 TC74HC393AF TC9246F HD74HCT126FP
NJM4580M UPD63710GC BA5985FM PD0236AM PE5011C
PML004AF
67
+ -
4
3
2
1 19
18
17
16
15
14
13
12
11
10
9
8
7
6
5 25
24
23
22
21
Amp4 Mute
20
Amp3
OUT2+
Amp1
VCC
Amp2
OUT1-
STBY
P-GND1
Mute
OUT1+
Mute
SVR
Mute
IN1
Protector
IN2
3
S-GND
VCC
VOUT
IN4
OUT4+
2
IN3
MUTE
VIN
TAB
Ac_gnd
OUT4-
1
P-GND2
OUT3+
P-GND4
GND
STBY
OUT2-
OUT3-
P-GND3
Switch_out
68
S-81250SGUP PA2028A
PAL005A
DEH-P900R,P9050
DEH-P900R,P9050 PM4009A
- Pin Functions (PD5483A, PD5484A) Pin No. 1 2 3 4 5 6 7 8,9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30
Pin Name TUNPDO TUNPCK TUNPCE TUNPCE2 MOSENS DLSENS IPPW VSS1,2 ASENBO TELIN RESET OSC1 VSS3 OSC2 VCC1 NMI rck ldet DALMON RX2 SYSPW ISENS PEE RDS57K FLPPW MUTE MICSENS RX TX
I/O O O O O I I O O I I O O
I I O I O I O I O O I I O
Function and Operation PLL data output PLL clock output PLL chip enable output PLL chip enable output 2 Motion/window damage sensor input Door lock sense input IP-BUS power supply control output GND IP-BUS slave power supply control output Cellular mute input Reset input Oscillator connection pin 1 GND Oscillator connection pin 2 5V Pull up RDS clock input PLL lock sense input DFS alarm output IP-BUS data input 2 System power supply control output Illumination sense input Beep tone output 57kHzBP-OUT sense input Flap motor driver power ON/OFF output Mute output Microphone sense input IP-BUS data input IP-BUS data output
69
DEH-P900R,P9050
Pin No. 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50–61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89,90 91 92 93 94 95 96 97 98 99 100
70
Pin Name BSO BSI BSCK FLPOPN DPDT KYDT FLPCLS FOPENSW NC FCLSSW DLED NC FLPILM ILMPW SWVDD OELPW DSENS ST SD NC VCC3 NC VSS4 VCK/ROMCLK VDT/ROMDATA VST/BSRQ2 NC BRXEN BRST BSRQ NC BSENS ASENS STOUT DRELAY LOCH LOCL NC NC FM/AM TMUTE DRST RDSLK RDT DRSENS DRSYS TESTIN NC LEVELR LEVELL NC SD_BW NC VSS5 SL VREF VCC4 TUNPDI
I/O O I I/O O O I O I I O O O O O I I I
O O/I O/I I/O O I/O I I O O O O O O O O I I I O I I I I
I
I
Function and Operation P-BUS communication data output P-BUS communication data input P-BUS serial clock input/output Flap motor open output Display serial data output Display enable data input Flap motor close output Flap open switch input Not used Flap close switch input Alarm LED output Not used Inside of flap illumination output Illumination power supply control output Display chip select output OEL module power supply control output Grille detach sense input FM stereo input SD input Not used 5V Not used GND E-VOL clock output / ROM correction clock output E-VOL data output / ROM correction data input E-VOL strobe pulse output / P-BUS communication input/output Not used P-BUS communication input/output P-BUS reset output P-BUS communication request input/output Not used Back up power sense input ACC power sense input Starter cut output External relay output Local “H” output Local “L” output Not used Open FM/AM power select output Tuner mute output RDS decoder reset output RDS lock signal input RDS data input Door open/close sense input Door system select output Test mode IN/test enable Not used Level meter “R“ AD input Level meter “L“ AD input Not used SD input Not used GND Signal level input A/D converter reference voltage 5V PLL data input
DEH-P900R,P9050
1
30
*PD5483A, PD5484A
31
100 IC's marked by* are MOS type. Be careful in handling them because they are very liable to be damaged by electrostatic induction.
50
16
15
14
13
RIN
RNF
OUT2
BA6288FS
VREF
80
51
81
12
11
10
9
7
8
DRIVER
CONTROL LOGIC
POWER SAVE
TSD
3
4
5
6
VM
VCC
FIN
2
GND
1
OUT1
DRIVER
BR9010FV NC
VCC
1
8
WC
GND
CS
2 CS : Chip select input 7 SK : Serial data clock input DI : Serial data input DO : Serial data output 3 WC: Write control input 6
SK
4
DI
5
DO
71
DEH-P900R,P9050
- Pin Functions (PD5471A) Pin Name NC REM BYTE CNVSS NC reset XOUT VSS XIN VDD nmi NC kd1-4 ks1-6 NC ILMD KYDT DPDT NC OEL rdy NC hold NC rd NC wr NC cs2 cs1 cs0 A19 NC A17-9 VDD A8 VSS A7-1 NC D15-0 NC AVSS NC VREF AVCC NC 50
*PD5471A
I/O
Format
I I I I O I I I I/O O O I
C C
O I
C
I O
C
O
C
O O O O
C C C C
O
C
O
C
O
C
I/O
Function and Operation Not used Remote control reception External data BUS width select input Processor mode select input Not used Reset input Crystal oscillating element connection pin GND Crystal oscillating element connection pin VDD NMI input Not used Key data 1-4 Key strobe input/output 1-6 Not used Dual illumination Key data output Display data input Not used OEL controller ON OEL controller ready input Not used Hold input Not used Read strobe Not used Write strobe Not used Bank address (High) Bank address (Low) External ROM chip select Address bus Output Not used Address bus Output VDD Address bus Output GND Address bus Output Not used Data bus input/output Not used Connect to VSS Not used Connect to VSS Connect to VCC Not used
26
Pin No. 1–4 5 6 7 8,9 10 11 12 13 14 15 16 17–20 21–26 27–31 32 33 34 35 36 37 38 39 40,41 42 43 44 45 46 47 48 49 50 51-59 60 61 62 63–69 70 71–86 87–93 94 95 96 97 98-100
25
51
Format C 1
72
100
76
75
Meaning C MOS
DEH-P900R,P9050
PD8051A
NC
1
48
NC
NC
2
47
NC
NC
3
46
NC
A18
4
45
A19
A17
5
44
A8
A7
6
43
A9
A6
7
42
A10
A5
8
41
A11
40
A12
39
A13
38
A14
37
A15
13
36
A16
A4
9
A3
10
A2
11
A1
12
A0
A0-A19 D0-D15 byte ce oe VCC VSS
:Address input :Data output :8/16 bit mode select :Chip enable input :Output enable input :Power supply :GND
ce
14
35
byte
VSS
15
34
VSS
oe
16
33
D15/A1
D0
17
32
D7
D8
18
31
D14
D1
19
30
D6
D9
20
29
D13
D2
21
28
D5
D10
22
27
D12
D3
23
26
D4
D11
24
25
VCC
*PD5504A 80
61
1
60
20
41 21
40
73
DEH-P900R,P9050 - Pin Functions (PD5504A) Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18–23 24 25 26 27 28 29 30 31 32 33 34,35 36 37 38 39 40 41 42 43 44–47 48 49 50 51 52–57 58 59 60 61 62 63 64 65 66 67 68–72 73 74 75 76 77 78 79 80 74
Pin Name NC NC VST VDT VCK CNVSS MCKRQ EMPHIN reset XOUT VSS XIN VCC NMI BMUTEIN NC brst NC DSPOUT DSPIN DSPCK NC BSO BSI BSCK NC bsrq brxen NC MICSENS IFHIZ AQTEST testin DSPPW MUTERQ NGO SYSMUTE NC PLLLOC PLLCLR PLLDT PLLCK NC LRCKK MCKOUT SMODE AKPD AKRST AKJMP dspcs akwrq dspack akrdy NC MDSEL2 NOISE AVSS NC VREF AVCC NC NC
I/O
Format
O O O I I I I O
C C C
O
I I I I O I O
C
O I I/O
C
C
I/O I/O I I I I O O O O
C C C C
I O O O
C C C
O O O O O O O O I I I I I I
C C C C C C C C
Function and Operation VSS joint Not used Electronic volume strobe output Electronic volume data output Electronic volume clock output VSS joint CD unit MCK request input CD unit emphasis data input Reset input Crystal oscillating element connection pin GND Crystal oscillating element connection pin 5V NML joint CD unit LR clock supply input VSS joint P–BUS reset input Not used DSP serial data output DSP serial data input DSP serial clock output Not used P–BUS serial data output P–BUS serial data input P-BUS serial clock input/output Not used P-BUS service request output pin Reception enable input/output Not used A.EQ microphone connection data input DSP microcomputer port Hiz set input A.EQ test mode start input Test mode IN/test enable input Power supply for DSP Hard mute output Digital zero output System mute output Not used PLL Lock supply data input PLL control clear output PLL control data output PLL control clock output Not used LRCK/BCLK select control output CD MCLK gate control AK7714 master/slave select input AK7714 power down AK7714 reset AK7714 condition jump AK7714 chip select output AK7714 data output request DSP data write ready supply input AK7714 data ready Not used Model select input ASL noise input A/D GND Not used A/D converter reference voltage input A/D VCC VSS joint Not used
DEH-P900R,P9050
- Pin Functions (AK7714) Pin No. 1,2 3–6 7 8 9 10,11 12 13 14 15 16 17 18 19 20 21,22 23 24 25,26 27 28 29 30,31 32,33 34 35 36 37 38 39 40 41 42,43 44,45 46 47 48 49 50–52 53 54 55 56 57 58 59 60-62 63 64 65 66,67 68 69 70,71 72 73
Pin Name NC TEST DVB NC DVDD DVSS SDINA NC SDOUTA SDOUTD1 NC SDINDI SDIND2 NC SDOUTD2 NC SDIN1 SDIN2 NC XTI XTO NC DVSS DVDD OPCL CLKO LRCLK BITCLK NC DRDY SO RDY DVSS DVDD NC wrq cs JX NC SI NC SCLK NC dsp reset code creset initrese NC CKS0 CKS1 SMODE DVSS DVDD NC DVB NC AOUTR2
I/O I
I O O I I O I I I O
I O I/O I/O O O O
I I I I I I I I I I I
O
Function and Operation Not used Test terminal 1-4 Power supply (5v) Not used Digital VDD (5V) Digital GND (0V) DSP serial data input Not used ADC serial data output DSP serial data output Not used DAC1 serial data input DAC2 serial data input Not used DSP serial data output Not used DSP serial data input DSP serial data input Not used Oscillation input Oscillation output Not used Digital GND (0V) Digital VDD (5V) ADC/DAC joint select input Clock output L/R channel select input/output Serial bit clock input/output Not used Output data ready output for microcomputer interface Serial data output for microcomputer interface Data write ready output for microcomputer interface Digital GND (0V) Digital VDD (5V) Not used Write request input for microcomputer interface Chip select input for microcomputer interface External condition Jump terminal Not used Serial data input for microcomputer interface Not used Serial data clock for microcomputer interface Not used Reset Reset Reset Not used Clock select input Clock select input Slave mode/master mode select input Digital GND (0V) Digital VDD (5V) Not used Power supply (5v) Not used DAC2 Rch analog output
75
DEH-P900R,P9050
Pin No. 74 75,76 77 78 79 80 81 82 83 84,85 86 87,88 89 90 91,92 93 94 95 96 97 98 99 100
Pin Name AOUTL2 NC AOUTR1 AOUTL1 NC AVB NC VRDAL AVSS AVDD VRDAH VCOM VRADL AVSS AVDD VRADH NC AINRAINR+ NC AINRAINR+ NC
I/O O O O
I
I O I
I I I I I
26
50
*AK7714
75
1
76
100
25
76
51
Function and Operation DAC2 Lch analog output Not used DAC1 Rch analog output DAC1 Lch analog output Not used Power supply (5V) Not used DAC reference voltage input Analog GND (0V) Analog power supply (5V) DAC reference voltage input Common voltage ADC reference voltage input Analog GND (0V) Analog power supply (5V) ADC reference voltage input Not used ADC Rch analog inverted input ADC Rch analog input Not used ADC Rch analog inverted input ADC Rch analog input Not used
DEH-P900R,P9050
TC74HC393AF
TC9246F Lock Detection Circuit
14 VCC
1ck 1
REF 1 REF
D
CK R q
D
12 2CLR D
R q
1QB 4
11 2QA D
AMPI 4
CK R q
D
AMPO 5
CK
VCO
10 2QB
1QC 5 CK R q
VDDA 3
CK
R
D q
9 2QC
1QD 6 D
15 LOCK
14 S2
Micon Interface
CK R q
1QA 3
Programmable Counter
D
VAR
CK R q
PD 2
Phase Comparator
13 2ck
1CLR 2
16 VDD
13 S1
12 M2
11 M1
VSSA 6
CK R q
GND 7
8 2QD
10 CKO
XI 7
Selector
XO 8
HD74HCT126FP
1C 1
1A 2
NJM4580M
14 VCC
13 4C
8 V+
A OUT 1
7 B OUT
A-IN 2
A 1Y 3
2C 4
2A 5
2Y 6
GND 7
9 VSS
B
12 4A
A+IN 3
6 B-IN-
11 4Y
V- 4
5 B+IN
10 3C
9 3A
8 3Y
77
DEH-P900R,P9050
- Pin Functions (UPD63710GC) Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14, 15 16 17 18 19 20 21 22 23 24 25 26 27 28
78
Pin Name GND HOLD MIRR FOK rst A0 stb sck SO SI VDD DA.VDD NC DA.GND NC DA.VDD R+ RLL+ X.VDD xtal XTAL X.GND VDD EMPH FLAG
I/O I/O I/O O I I I I O I
O O O O O I
O O
29 30 31 32 33 34
DIN DOUT SCKIN SCKO LRCKIN LRCK
I O I O I O
35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58
WDCK TX GND C16M LIMIT VDD LOCK RFCK WFCK PLCK GND C1D1 C1D2 C2D1 C2D2 C2D3 VDD PACK TSO TSI tsck TSTB GND TEST
O O O I O O O O O O O O O O O I I I I
Function and Operation Logic circuit GND Defect detection output MIRR output RFOK signal output Reset signal input Command/parameter identification signal input Data strobe signal input Clock signal input for serial data input/output Serial data and status signal output Serial data input Positive power supply terminal to logic circuit Positive power supply terminal to D/A converter Not used D/A converter GND Not used Positive power supply terminal to D/A converter Right channel audio data output Right channel audio data output Left channel audio data output Left channel audio data output Positive power supply terminal to crystal oscillation circuit Crystal oscillator connect pin Crystal oscillator connect pin Crystal oscillation circuit GND Positive power supply terminal to logic circuit Output pin for the pre-emphasis data in the sub-Q code Flag output pin to indicate that audio data currently being output consists of noncorrectable data Serial data input to internal DAC Serial audio data output Serial clock input to internal DAC Audio data that is output from DOUT changes at rising edge of this clock LRCK signal input to internal DAC Signals to distinguish the right and left channels of the audio data output from DOUT Output double the frequency of LRCK Digital audio interface data output Logic circuit GND Oscillator clock buffering output Status of the pin is output at Bit 5 of the status output Positive power supply terminal to logic circuit EFM synchronous detection signal Frame synchronous signal of XTAL-system Frame synchronous signal of PLL-system Monitor pin of bit clock Logic circuit GND Output pin for indicating the C1 error correction results Output pin for indicating the C1 error correction results Output pin for indicating the C2 error correction results Output pin for indicating the C2 error correction results Output pin for indicating the C2 error correction results Positive power supply terminal to logic circuit CD-TEXT PACK synchronous signal CD-TEXT data serial output CD-TEXT control parameter serial input CD-TEXT serial clock input CD-TEXT parameter strobe signal input Logic circuit GND Test pin
DEH-P900R,P9050
Pin No. 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100
Pin Name ATEST RFMODE A.GND FD TD SD MD DACO FBAL TBAL TEVCA A.VDD EFM ASY C3T RFI AGCO AGCI RFO EQ2 EQ1 RFA.GND A C B D F E A.VDD REFOUT FEFEO TETEO TE2 TEC A.GND PD LD PN A.VDD
I/O I/O I O O O O O O O O O I I O I O
I I I I I I I O I I/O I I/O I/O I I O I
Function and Operation Test pin Use/not use select for internal RF amplifier Analog circuit GND Focus drive output Tracking drive output Sled drive output Spindle drive output DAC output for adjustment DAC output for adjustment DAC output for adjustment DAC output for adjustment Power supply terminal to analog circuit EFM signal output EFM comparator reference voltage input 3T detection capacitor additional pin RF signal input for EFM data regulation RF signal output of after gain adjustment RF-AGC amplifier input RF summing amplifier output RF amplifier equalizer parts additional pin RF amplifier equalizer parts additional pin RF summing amplifier inverted input Analog circuit GND Photo detector A input Photo detector C input Photo detector B input Photo detector D input Photo detector F input Photo detector E input Positive power supply terminal to analog circuit Reference electric potential output Focus error amplifier inverted input Focus error amplifier output Tracking error amplifier inverted input Tracking error amplifier output Tracking error output of after amplification Tracking comparator input Analog circuit GND PD detection signal input for LD output monitor LD control current output APC circuit control polarity set pin Positive power supply terminal to analog circuit
26
50
*UPD63710GC
75
1 100
25
76
51
79
DEH-P900R,P9050 - Pin Functions (BA5985FM) Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28
Pin Name FWD OPIN1(+) OPIN1(−) OPOUT1 OPIN2(+) OPIN2(−) OPOUT2 VCC VOL(−) VOL(+) VO2(−) VO2(+) VO1(−) VO1(+) VO4(+) VO4(−) VO3(+) VO3(−) GND BIAS MUTE OPOUT3 OPIN3(−) OPIN3(+) OPOUT4 OPIN4(−) OPIN4(+) REV
I/O I I I O I I O O O O O O O O O O O I O I I O I I I
Function and Operation Loading driver FWD input CH1 pre-amplifier input CH1 pre-amplifier inverted input CH1 pre-amplifier output CH2 pre-amplifier input CH2 pre-amplifier inverted input CH2 pre-amplifier output Power supply Loading driver negative output Loading driver positive output Driver CH2 negative output Driver CH2 positive output Driver CH1 negative output Driver CH1 positive output Driver CH4 positive output Driver CH4 negative output Driver CH3 positive output Driver CH3 negative output GND Bias input Mute control CH3 pre-amplifier output CH3 pre-amplifier inverted input CH3 pre-amplifier input CH4 pre-amplifier output CH4 pre-amplifier inverted input CH4 pre-amplifier input Loading driver REV input
BA5985FM PD0236AM
- Pin Functions (PD0236AM) Pin No. 1 2 3 4 5 6 7 8 9 10 11 12,13 14 15 16 17 18 80
Pin Name BCSEL DASEL NC LRSEL LRCKO NC BCKO DATAO GND VDD LRCKI NC DATAI BCKI NC SEL XRST
I/O I I
O O O
I I I I I
Function and Operation Bit clock fs select Bit expand select Not used LRCKO polarity select LRCKO output Not used Bit clock output Data output GND Power supply terminal LRCKO input Not used Data input Bit clock input Not used Bit expand/input data output select Reset input
9
1
10
18
DEH-P900R,P9050
- Pin Functions(PE5011C) Pin No. 1 2 3 4 5-8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23, 24 25 26 27 28 29 30 31 32, 33 34 35-44 45 46 47 48 49 50 51 52 53, 54 55 56 57 58 59 60 61, 62 63-66 67 68 69 70 71 72 73 74 75 76
Pin Name EJTSNS DSCSNS VDSENS TEMP NC AVREF reset XT1 XT2 IC(VPP) X1 X2 VDD VSS xsck XSO XSI brst pack NC XA0 xstb xrst FOK MIRR LOCK CD5VON NC EMPH NC VSS VDD adena VDCONT NC csens BRXEN bsrq NC CONT CDMUTE CDEJET CDLOAD BMUTE clamp NC NC TXARI fsck FTXD FRXD bsck BDATA testin NC TSTB NC
I/O
Format
I I
I
O O I
C C
O O O I I I O
C C C
O
C
O O
C C
I I/O O
/C C
O O O O O I
C
C C C C C
I O O O I/O I/O I
C C C /C /C
O
C
Function and Operation Disc eject position sense input Disc insert position sense input VD power supply short sense input Temperature sense input Not used VSS A/D reference voltage input System reset input VDD Open VSS Main clock radiator(8.38MHz)connection Main clock radiator(8.38MHz)connection Power supply(+5V) GND CD LSI serial clock output CD LSI serial data output CD LSI serial data input P-Bus reset input CD-TEXT pack sync signal input Not used Open CD LSI data discrimination control signal output CD LSI strobe output CD LSI reset output Focus OK input Specular surface detection input Spindle lock input CD +5V power supply control output Not used Open Emphasis information output Not used Open GND Power supply(+5V) A/D reference voltage supply control output VD power supply control output Not used Open Flap close sense input Input/output by which P-Bus can be received P-Bus polling request output Not used Open Servo driver power supply control output CD mute control output Load/Eject motor Eject control output Load/Eject motor Load control output Bus mute output Disc clamp input Not used Open Not used VDD or VSS Tx output set selection input Flash writing clock input(Open) Flash writing data output(Open) Flash writing data input(Open) P-Bus serial clock input/output P-Bus serial data input/output Test program start input Not used Open CD-TEXT strobe output Not used Open
81
DEH-P900R,P9050
Pin No. 77 78 79 80
Pin Name tsck TSO TSI AVSS
I/O O O I
Format C C
80
40
61 60
21
41 82
1
20
*PE5011C
Function and Operation CD-TEXT serial clock output CD-TEXT serial data output CD-TEXT serial data input A/D GND
IP-BUS input (Blue)
This Product
Fuse holder
Fuse holder
Black (ground) To vehicle (metal) body.
Orange/White To lighting switch terminal.
Rear output
Perform these connections when using a different amp (sold separately).
Subwoofer
Rear speaker
Rear speaker
Left
Front speaker
Front speaker
Subwoofer output or Non-Fading output Blue/white To system control terminal of the power amp or Auto-antenna relay control terminal. (Max. 300 mA 12 V DC.)
With a 2 speaker system, do not connect anything to the speaker leads that are not connected to speakers.
Fuse resistor
Red Fuse resistor To electric terminal controlled by ignition switch (12 V DC) ON/OFF.
Yellow To terminal always supplied with power regardless of ignition switch position.
White/yellow
Brown
White/red
White/orange
Blue/brown
Yellow/black If you use a cellular telephone, connect it via the Audio Mute lead on the cellular telephone. If not, keep the Audio Mute lead free of any connections. See the section “DFS Alarm Installation”.
IP-BUS cable
Multi-CD player (sold separately)
Antenna jack
ASL unit
Front output
≠
+
≠
+
≠
+
≠
+
≠
+
Green/black
Green
White/black
White
Violet/black
Violet
Gray/black
Gray
System remote control
Connecting cords with RCA pin plugs (sold separately)
≠
+
≠
+
≠
+
≠
+
≠
+
Subwoofer
Rear speaker
Rear speaker
Right
Front speaker
Front speaker
Power amp (sold separately)
Power amp (sold separately)
Power amp (sold separately)
DEH-P900R,P9050
8. OPERATIONS AND SPECIFICATIONS
- Connection Diagram (DEH-P900R/UC)
83
84
IP-BUS input (Blue)
This Product
Fuse holder
Fuse holder
Black (ground) To vehicle (metal) body.
Orange/White To lighting switch terminal.
Rear output
Perform these connections when using a different amp (sold separately).
Subwoofer
Rear speaker
Rear speaker
Left
Front speaker
Front speaker
Blue/white To system control terminal of the power amp or Auto-antenna relay control terminal. (Max. 300 mA 12 V DC.)
Subwoofer output or Non-Fading output
With a 2 speaker system, do not connect anything to the speaker leads that are not connected to speakers.
Fuse resistor
Red Fuse resistor To electric terminal controlled by ignition switch (12 V DC) ON/OFF.
Yellow To terminal always supplied with power regardless of ignition switch position.
White/yellow
Brown
White/red
White/orange
See the section “DFS Alarm Installation”.
Yellow/black If you use a cellular telephone, connect it via the Audio Mute lead on the cellular telephone. If not, keep the Audio Mute lead free of any connections.
IP-BUS cable
Multi-CD player (sold separately)
Antenna jack
ASL unit
Front output
≠
+
≠
+
≠
+
≠
+
≠
+
Green/black
Green
White/black
White
Violet/black
Violet
Gray/black
Gray
System remote control
Connecting cords with RCA pin plugs (sold separately)
≠
+
≠
+
≠
+
≠
+
≠
+
Subwoofer
Rear speaker
Rear speaker
Right
Front speaker
Front speaker
Power amp (sold separately)
Power amp (sold separately)
Power amp (sold separately)
DEH-P900R,P9050
- Connection Diagram (DEH-P9050/ES)
DEH-P900R,P9050
8.1 OPERATIONS (DEH-P900R/UC))
DISPLAY button RESET button
FUNCTION button
ENTERTAINMENT button
EJECT button
5/∞/2/3 buttons
EQ button
+/– button
Buttons 1–6 PGM button
SOURCE/OFF button
BAND button PTY button AUDIO button RT button
ATT button This lets you quickly lower volume level (by about 90%). Press once more to return to the original volume level.
+/– button BAND button
FUNCTION button
5/∞ buttons
PGM button
AUDIO button 2/3 buttons
SOURCE/OFF button
85
86
Hold for 1 second or more
3. Source OFF.
2. Raise or lower the volume.
• In the following cases, the sound source will not change: * No TV tuner is connected to this product. * No Multi-CD player is connected to this product. (When “Multi-CD” display is OFF. * No DAB tuner is connected to this product. * No disc is set in this product. * No magazine is set in the Multi-CD player. * AUX (external input) is set to OFF.
Note:
Each press of the SOURCE/OFF button selects the desired source in the following order: Built-in CD player (Compact Disc) = TV (Television) = Tuner = DAB (Digital Audio Broadcasting) Tuner = Multi-CD player = AUX
Each press changes the Source ...
1. Select the desired source (e.g. Tuner).
• Loading a disc in this product.
Note:
The following explains the initial operations required before you can listen to music.
To Listen to Music
Basic Operation
0.5 seconds or more
Seek Tuning
2 seconds or more
Broadcast station preset memory
• Up to 18 FM stations (6 in FM-1, FM-2 and FM-3) and 6 AM stations can be stored in memory. • You can also use the 5 or ∞ buttons to recall broadcast stations memorized in buttons 1 through 6.
Note:
2 seconds or less
Preset station recall
FM-1 = FM-2 = FM-3 = AM
Band
Frequency Indicator
• You can memorize broadcast stations in buttons 1 through 6 for easy, one-touch station recall.
Preset Tuning
Band Indicator
Preset Number Indicator
• If you continue pressing the button for longer than 0.5 seconds, you can skip broadcast stations. Seek Tuning starts as soon as you stop pressing the button. • “” stereo indicator lights when a stereo station is selected.
Note:
0.5 seconds or less
Manual Tuning (step by step)
• You can select the tuning method by changing the length of time you press the 2/3 button.
Manual and Seek Tuning
Basic Operation of Tuner
DEH-P900R,P9050
• A CD TEXT disc is a CD featuring recorded text information such as Disc Title, Artist Name and Track Title. • If you switch a display when the disc title has not been input, “No Title” is displayed. • If you switch a display when the disc artist has not been input, “No Artist Name” is displayed. • If you switch a display when the track title has not been input, “No Title” is displayed. • If you switch a display when the track artist has not been input, “No Artist Name” is displayed.
Note:
Each press of the DISPLAY button changes the display in the following order: Playback mode (Play Time) = Disc Title = Disc Artist = Track Title = Track Artist With text longer than 20 letters, you can scroll to see the rest of the text by pressing the DISPLAY button for 2 seconds or more.
Switching the Display (only for CD TEXT Discs)
Track Number Indicator
Play Time Indicator
• The CD function can be turned ON/OFF with the disc remaining in this product. • Discs left partially inserted after ejection may incur damage or fall out.
Note:
• If you switch a display when the disc title has not been input, “No Title” is displayed.
Note:
Press the EJECT button, and you can open the front panel before ejection. In case of opening the front panel, you can just eject a CD.
Eject
Each press of the DISPLAY button changes the display in the following order: Playback mode (Play Time) = Disc Title
Switching the Display
Basic Operation of Built-in CD Player
Basic Operation
• If a disc cannot be inserted fully or playback fails, make sure the recorded side is down. Push the EJECT button and check the disc for damage before reinserting it. • If the Built-in CD player cannot operate properly, an error message (such as “ERROR-14”) appears on the display.
Note:
If a CD is inserted, the front panel is closed automatically. The Built-in CD player plays one standard 12 cm or 8 cm (single) CD at a time. Do not use an adapter when playing 8 cm CD.
• Do not use with the front panel left open. If you do leave it open, it may result in injury in the event of an accident.
WARNING:
• When opening the front panel, the 1 to 6 buttons are not available.
Note:
Press the EJECT button for 1 second or more, and you can open the front panel without ejecting a CD. In case of opening the front panel, you can close it.
Open
Continue pressing
0.5 seconds or less
Disc Loading Slot
Fast Forward/Reverse
Track Search
• You can select between Track Search or Fast Forward/Reverse by pressing the 2/3 button for a different length of time.
Track Search and Fast Forward/Reverse
DEH-P900R,P9050
87
88 Continue pressing
Fast Forward/Reverse
• If you switch displays when disc titles have not been input, “No Title” is displayed.
Note:
Each press of the DISPLAY button changes the display in the following order: Playback mode (Play Time) = Disc Title
Switching the Display
Disc Number Indicator
Magazine 1 = Magazine 2 = Magazine 3 (Displayed about for 2 seconds.)
When two or more Multi-CD players are connected using a multiple connection adapter, you can select the Multi-CD player by pressing the BAND button.
Switching the Multi-CD Player
Disc Search
Play Time Indicator
Track Number Indicator
0.5 seconds or less
Track Search
• You can select between Track Search or Fast Forward/Reverse by pressing the 2/3 button for a different length of time.
Track Search and Fast Forward/Reverse
This product can control a Multi-CD player. (With certain old type Multi-CD players, using a multiple connection adapter lets you connect multiple units which you can control with this product.)
Basic Operation of Multi-CD Player
Basic Operation
• You can use the following two functions. Refer to Multi-CD Player’s Owner’s Manual for operation details. * Title display switching * Title scroll • You cannot switch to the Disc Title Input mode in the Detailed Setting Menu.
When playing a CD TEXT disc on a CD TEXT compatible Multi-CD Player such as the CDX-P656:
• The Multi-CD player may perform a preparatory operation, such as verifying the presence of a disc or reading disc information, when the power is turned ON or a new disc is selected for playback. “READY” is displayed. • When a magazine is loaded into a 50-Disc type Multi-CD Player, information on all the discs in the magazine is read. If you start playing a disc on a 50-Disc type Multi-CD Player before reading of information on all discs has been completed, reading of information stops part way through. This will prevent you from using the ITS function. (If you try and use this function, “Not Ready” is displayed.) If this happens, reading of information begins again when you switch to a component other than the 50-Disc Type Multi-CD Player. • If the Multi-CD player cannot operate properly, an error message such as “ERROR-14” is displayed. Refer to Multi-CD Player Owner’s Manual. • If there are no discs in the Multi-CD player magazine, “No Disc” is displayed. • “LOADING” will be displayed in the following cases: * If the disc in the extra tray in selected. * If the disc in moved from the extra tray to the magazine. (Refer to the 50-Disc Type Multi-CD Player Owner’s Manual.) • You cannot use the “Ejecting a Single Disc”, “Frequency Play”, “Music Group Play” or “ABC Disc Title Search” functions with this product.
Note:
• After completing a rough search, use the 5 and ∞ buttons to select a desired disc.
Note:
• Select the desired block with the 1 to 5 buttons.
This handy function lets you select discs loaded in a 50-Disc Multi-CD Player using the 1 to 5 buttons. The 50 discs are divided into five blocks, with each of the 1 to 5 buttons assigned to a block.
Disc Number Rough Search (for 50-Disc type only)
• When a 12-Disc Multi-CD Player is connected and you want to select disc 7 to 12, press the 1 to 6 buttons for 2 seconds or longer.
Note:
• You can select discs directly with the 1 to 6 buttons. Just press the number corresponding to the disc you want to listen to.
Disc Number Search (for 6-Disc, 12-Disc types)
DEH-P900R,P9050
Continuous power output is 22 W per channel min. into 4 ohms, both channels driven 50 to 15,000 Hz with no more than 5% THD. Maximum power output ...................................... 45 W × 4 45 W × 2 ch/4 Ω + 70 W × 1 ch/2 Ω (for Subwoofer) Load impedance ...................... 4 Ω (4 – 8 Ω [2 Ω for 1 ch] allowable) Preout maximum output level/ output impedance .................................. 6.5 V/100 Ω Loudness contour (Low) .................. +3.5 dB (100 Hz), +3 dB (10 kHz) (Mid) ................ +10 dB (100 Hz), +6.5 dB (10 kHz) (High) ................ +11 dB (100 Hz), +11 dB (10 kHz) (volume: –30 dB) Equalizer (13-Band Graphic Equalizer) Frequency ................ 50/80/125/200/315/500/800 Hz 1.3/2/3.2/5/8/12.5 kHz Equalization range................................ ±12 dB (2 dB) Auto Equalizer (Front & Rear & Subwoofer 13-Band Graphic) Frequency ................ 50/80/125/200/315/500/800 Hz 1.3/2/3.2/5/8/12.5 kHz Equalization range .................... ±6 — –12 dB (2 dB) Network HPF Frequency .................................... 50/80/125 Hz Slope ................................................ –12 dB/oct. Subwoofer output Frequency .................................... 50/80/125 Hz Slope ................................................ –18 dB/oct. Gain ........................................................ ±12 dB Phase ........................................ Normal/Reverse
Audio/DSP
System .................................... Compact disc audio system Usable discs .................................................. Compact disc Signal format .................... Sampling frequency: 44.1 kHz Number of quantization bits: 20; linear Frequency characteristics .............. 5 – 20,000 Hz (±1 dB) Signal-to-noise ratio ...... 110 dB (1 kHz) (IHF-A network) Dynamic range ............................................ 94 dB (1 kHz) Number of channels ............................................ 2 (stereo)
Power source .......... 14.4 V DC (10.8 – 15.1 V allowable) Grounding system ........................................ Negative type Max. current consumption ...................................... 10.0 A Dimensions (DIN) (chassis) ...... 178 (W) × 50 (H) × 155 (D) mm [7 (W) × 2 (H) × 6-1/8 (D) in.] (nose) ............ 188 (W) × 58 (H) × 20 (D) mm [7-3/8 (W) × 2-1/4 (H) × 3/4 (D) in.] (D) (chassis) ...... 178 (W) × 50 (H) × 160 (D) mm [7 (W) × 2 (H) × 6-1/4 (D) in.] (nose) ............ 170 (W) × 46 (H) × 15 (D) mm [6-3/4 (W) × 1-3/4 (H) × 5/8 (D) in.] Weight ........................................................ 1.8 kg (4.0 lbs)
Audio/DSP
Power source .......... 14.4 V DC (10.8 – 15.1 V allowable) Grounding system ........................................ Negative type Max. current consumption ...................................... 10.0 A Dimensions (DIN) (chassis) ...... 178 (W) × 50 (H) × 155 (D) mm (nose) .......... 188 (W) × 58 (H) × 20 (D) mm (D) (chassis) ...... 178 (W) × 50 (H) × 160 (D) mm (nose) .......... 170 (W) × 46 (H) × 15 (D) mm Weight ...................................................................... 1.8 kg
General
Note: • Specifications and the design are subject to possible modification without notice due to improvements.
Note: • Specifications and the design are subject to possible modification without notice due to improvements.
Frequency range ........................ 531 – 1,602 kHz (9 kHz) 530 – 1,710 kHz (10 kHz) Usable sensitivity .............................. 18 µV (S/N: 20 dB) Selectivity .................................................. 50 dB (±9 kHz) 50 dB (±10 kHz)
AM tuner
Frequency range ...................................... 87.5 – 108 MHz Usable sensitivity .................. 10 dBf (0.9 µV/75 Ω, mono, S/N: 30 dB) 50 dB quieting sensitivity .... 15 dBf (1.5 µV/75 Ω, mono) Signal-to-noise ratio ...................... 70 dB (IEC-A network) Distortion .......................... 0.3% (at 65 dBf, 1 kHz, stereo) Frequency response ...................... 30 – 15,000 Hz (±3 dB) Stereo separation .......................... 40 dB (at 65 dBf, 1 kHz)
FM tuner
System .................................... Compact disc audio system Usable discs .................................................. Compact disc Signal format .................... Sampling frequency: 44.1 kHz Number of quantization bits: 20; linear Frequency characteristics .............. 5 – 20,000 Hz (±1 dB) Signal-to-noise ratio ...... 110 dB (1 kHz) (IEC-A network) Dynamic range ............................................ 94 dB (1 kHz) Number of channels ............................................ 2 (stereo)
CD player
Specifications (DEH-P9050/ES)
Continuous power output is 22 W per channel min. into 4 ohms, both channels driven 50 to 15,000 Hz with no more than 5% THD. Maximum power output ...................................... 45 W × 4 45 W × 2 ch/4 Ω + 70 W × 1 ch/2 Ω (for Subwoofer) Load impedance ...................... 4 Ω (4 – 8 Ω [2 Ω for 1 ch] allowable) Preout maximum output level/ output impedance .................................. 4.0 V/100 Ω Loudness contour (Low) .................. +3.5 dB (100 Hz), +3 dB (10 kHz) (Mid) ................ +10 dB (100 Hz), +6.5 dB (10 kHz) (High) ................ +11 dB (100 Hz), +11 dB (10 kHz) AM tuner (volume: –30 dB) Frequency range ...................................... 530 – 1,710 kHz Usable sensitivity .............................. 18 µV (S/N: 20 dB) Equalizer (13-Band Graphic Equalizer) Frequency ................ 50/80/125/200/315/500/800 Hz Selectivity ................................................ 50 dB (±10 kHz) 1.3/2/3.2/5/8/12.5 kHz Equalization Range ............................ ±12 dB (2 dB) Auto Equalizer (Front & Rear & Subwoofer 13-Band Graphic) Frequency (F&R&SW) ................ 50/80/125/200/315/ 500/800 Hz 1.3/2/3.2/5/8/12.5 kHz Equalization Range .................. +6 — –12 dB (2 dB) Network HPF Frequency .................................... 50/80/125 Hz Slope ................................................ –12 dB/oct. Subwoofer output Frequency .................................... 50/80/125 Hz Slope ................................................ –18 dB/oct. Gain ........................................................ ±12 dB Phase ........................................ Normal/Reverse
Frequency range .................................... 87.9 – 107.9 MHz Usable sensitivity .................................................... 10 dBf (0.9 µV/75 Ω, mono, S/N: 30 dB) 50 dB quieting sensitivity .... 15 dBf (1.5 µV/75 Ω, mono) Signal-to-noise ratio ...................... 70 dB (IHF-A network) Distortion .......................... 0.3% (at 65 dBf, 1 kHz, stereo) Frequency response ...................... 30 – 15,000 Hz (±3 dB) Stereo separation .......................... 40 dB (at 65 dBf, 1 kHz) Selectivity .................................................... 70 dB (2ACA) Three-signal intermodulation (desired signal level) ........................................ 30 dBf (two undesired signal level: 100 dBf)
FM tuner
CD player
General
Specifications (DEH-P900R/UC)
DEH-P900R,P9050
89
