Transcript
Code 211518
Deluxe Mitre Saw Stand
Index of Contents Page No Index of Contents
02
Specification
02
What’s in the Box
02-03
Safety Instructions
03
Assembly Instructions
04-05-06
Illustration & Description
07
Extending the Roller Assembly
08
Raise & Lower the Roller Assembly
09
Roller Assembly Work Stop
09
Mounting the Mitre Saw
10-11
symbols below advise that you follow the correct Warning The safety procedures when using this machine.
Fully read manual and safety instructions before use
Ear protection should be worn
Eye protection should be worn
Dust mask should be worn
Specification Code 211518 Folded:
L 1160mm x W 280mm x H 285mm
Assembled and Extended:
L 2840mm x W 780mm x H 1010mm
Length of Mounting Rails:
415mm
What’s in the Box 1 No.
Deluxe Mitre Saw Stand
A
2 No.
Saw Mounting Rails
B
1 No.
Instruction Manual
02
What’s in the Box
A
B
Safety Instructions Good Working Practices/Safety The following suggestions will enable you to observe good working practices, keep yourself and fellow workers safe and maintain your tools and equipment in good working order.
!
WARNING!!
KEEP TOOLS AND EQUIPMENT OUT OF THE REACH OF YOUNG CHILDREN
Please unpack the components of your mitre saw stand & check each item against “What’s in the Box” list. If any item is missing please contact our customer service department using the phone number on the back cover. Having unpacked your saw stand & its accessories please dispose of any unwanted packaging properly. The packaging is biodegradable. Only use the mitre saw stand on a flat and level surface. Ensure that all four legs are fully extended and the spring pins are locked in position. Make sure the mitre saw is correctly located on the stand and firmly secured in position. Carefully read and follow all the safety instructions for your mitre saw before starting work.
03
Assembly Instructions (Step 1) Place the stand (A) in the inverted position, push and hold the spring pin in and rotate the leg to its fully extended position, checking that when the leg is extended the spring pin re-engages the pre-drilled hole in the frame to lock it in position. Repeat for the remaining legs. (Step 2) Turn the stand (A) to the upright position. (Step 3) Locate one of the two mounting rails (B). Lift the locking lever so it is in the horizontal position, lower the mounting rail, so it engages over the sides of mitre saw stand rail (A) and push the locking lever down to lock it in position. Stand fully assembled.
Step 1
A
Spring pin
04
Spring pin locked in position
Assembly Instructions
Step 1 Support legs
A
Step 2
Turn stand (A) upright
05
Assembly Instructions Lower the saw mounting rail (B) over the mitre saw stand rail (A)
Push the locking handle down to lock the saw mounting rail in position
A
Un-lock
B
Lock
Locking handle
Step 3
06
Illustration & Description
Saw mounting rails
Fence
Roller
Mitre saw stand rail
Roller rise & full locking knob Carrying handle
Clamping handle
Leg
Carrying the mitre saw stand
07
Extending the Roller Assembly To extend the roller assembly follow the instruction below. 1. Push the roller lever lock (C) down to un-lock the roller assembly.
C
2. Hold the roller assembly (D) and pull towards you.
D 3. Pull the roller lever lock (C) back up to secure the roller assembly in position.
08
C
Raise & Lower the Roller Assembly To raise or lower the height of the roller assembly, simply undo the clamping knob (E) until the assembly is loose, adjust the height and then re-tighten the clamping knob (E) to secure it in position.
E
Roller Assembly Work Stop The roller assembly has a hinged work stop which can be raised or lowered when needed. See figs F, G & H below.
Timber
F
Raise the work stop in position
G
H
Work stop raised
Timber up against work stop
09
Mounting the Mitre Saw
!
WARNING!!
MAKE SURE THE LEGS FOR THE STAND ARE LOCKED IN PLACE BEFORE MOUNTING THE MITRE SAW ON THE STAND.
1). Set the saw mounting rails (B) to the approx width of your mitre saw. 2). Undo and remove the four M8 nuts, washers & spring washers. 3). Line up the four M8x50mm bolts (I) with the pre-drilled holes in your mitre saw and very carefully lower the mitre saw onto the rails. 4). Using the nuts, washers & spring washers (J) you removed earlier, secure the mitre saw in place using a 13mm spanner. When the mitre saw is seated on the mounting rails the whole assembly can be positioned where required and locked in place.
Approx width of your mitre saw
B
10
Mounting the Mitre Saw
I
I
B
J
11
Axminster Tool Centre, Unit 10 Weycroft Avenue, Axminster, Devon EX13 5PH
axminster.co.uk
