Transcript
design guide: display
The right amount of light LIGHT OUTPUT
TYPICAL APPLICATION
150lm
•
Point of purchase (POP) fixtures
300lm
• •
Lighter colored graphics Large scale applications where power consumption is a consideration
600lm
• •
Darker or multi-colored graphic materials High visibility applications
Good lighting is not about generating as much light as possible… Good lighting is about generating the right amount of light for your design.
Range map RANGE COMPONENT
PRODUCT LEVEL
REQUIRED
FUNCTION
OPTIONS
TILE
Standard
Yes
Modular illumination tile
Flux (lm): 600, 300, 150 CCT: 2700K, 3000K, 3500K, 4000K, 5700K CRI: >80
TILE
Plus
Yes
Modular illumination tile - high color rendering
Flux (lm): 600, 300, 150 CCT: 2700K, 3000K, 3500K, 4000K, 5700K CRI: >90
TILE
Premium
Yes
Modular display illumination tile - CCT tunable white
Flux (lm): 600, 300, 150 CCT: Tunable 2700K-5700K CRI: >90
REMOTE MOUNTED LED DRIVER
Standard and Plus
Yes
Converts mains line high voltage AC power to safe, low voltage Power: 90W, 50W, 30W (UL Listed) DC power (0/1-10V dimming)
REMOTE MOUNTED TUNABLE WHITE DRIVER
Premium
Yes
Converts mains (line) high voltage AC power to safe, low voltage DC power for operating Cooledge illumination products
TILE CONNECTOR KIT
All
Yes
Connector strip and wires used to connect power from the LED Driver to TILEs
TILE STARTER CABLE
All
Yes
10' (3m) cable that connects the driver to the connector strip
TILE CORNER KIT
All
Optional
Illumination tile and connectors used in corners
Flux (lm): 600, 300, 150 CCT: 2700K, 3000K, 3500K, 4000K, 5700K CRI: >80, >90
TILE CUT-OUT KIT
Standard Plus
Optional
Illumination tile and jumper wire used to cut around obstacles or align with angles & curves
Flux (lm): 600, 300, 150 CCT: 2700K, 3000K, 3500K, 4000K, 5700K CRI: >80, >90
EXTENSION CABLE
All
Optional
Additional cable between driver and starter cable to allow increased remote driver distances
Length: 10’ (3m), 20’ (6m), 50’ (15m)
DIMMING PROTOCOL CONVERTER
All
Optional
Converts DALI, DMX or Phase Cut dimming signal to 0/1-10V dimming protocol that is compatible with Cooledge LED Drivers
# Channels: Contact Cooledge for options.
Power: 90W, 50W, 30W (UL Listed) Control signal: 0/1-10V – 2 channels (for dimming + CCT tuning)
Supplied separately: DISPLAY FEATURE
Yes
Light box or display fixture that incorporates illumination to highlight graphics or merchandise
Display Type: Graphics or translucent fixture materials Setback Distance: The distance from the TILE to the illuminated surface determines if uniformity can be achieved
DIMMING CONTROLLER
Optional
Provides user interface and control signals for dimming the luminous ceiling
Protocols: 0/1 – 10V Standard DALI, DMX (requires protocol converter)
typical display section TILEs can be cut to length onsite to adjust for the height of the display and TILE Corner Kits are available to ensure complete coverage of the display area.
display layouts Cooledge TILE can be configured to address any size of display and provide full illumination coverage. Corner – cut to match Cooledge TILE (2x4)
Cooledge TILE – to fit run length
Cooledge TILE – cut to fit run width
Insulating Patch – covers traces on cut Cooledge TILE
Cooledge TILE – full size
Single Jumper Connector Strip – cut to fit Double Jumper (long) – for 90 ◦ connections
Starter Cable – cut to length
Connector Strip Double Jumper (short) – for straight connections
Driver Enclosure
useful tips Mounting surface • Suitable for non-conductive mounting surface without need for heat sinking • Connector strips can be mounted on right angle surfaces ensuring that the light emitting TILEs can be extended to the sides of the display to eliminate dark edges and shadows
Uniform Illumination • In contrast to side emitting options, TILE solutions will be uniform at any size • With uniformity at setbacks as small as 3”/75mm, large graphic displays will not consume valuable floor space
Working with Color • TILE Plus color rendering of >90 is available • Available in 5700K to make whites stand out or lower CCTs to enhance warmer colors
