Detailed Tender Notice No. Dte/pur/14/ 328 Dated 16-10-2014

Transcript

(“Group B”) Detailed Tender Notice No. DTE/PUR/14/ 328 Dated Electronics and communication Engineering Department 16-10-2014 1. Electronics and Instrumentation Lab. S. NO. 1. 2. NAME OF ARTICLE WITH SPECIFICATION Digital Multimeter 4½ Digit LCD Display, 7 Functions 29 Ranges, Continuity, Diode Test Facility Drop/Flash/Dust Proof Hand Held, True RMS Response Auto-polarityequipped with high voltage probe, DC current probe, manual DCV/ACV, 200 mv to1000v 200 uA to 10A Resistance 200 Ohm to 20 mOhm Accuracy ± 5% 9V Battery Operated Cathode Ray Oscilloscope: Operating Modes : Channel I, Channel II, Channel I &ll alternate or chopped (approximately 350 KHz), X-Y operation (Ratio 1:1 Input via CH II), Add/Sub CH I ± CH II, Invert CH II Bandwidth : DC -30 MHz (-3 dB) Electronic control. Display on 32 characterbacklit alphanumeric LCD Timebase Time coefficients : Microcontroller based 18 calibrated steps, 0.5 μs/cm-0.2 s/cm (1-2-5 sequence) Electronic control, Display on 32 character backlit alphanumeric LCD Magnifier : X10 Sawtooth out : 5 Vpp approximately Hold-Off : Variable Control for stable triggering Trigger System Trigger Bandwidth : 40 MHz Quantity required for GP Poonch GP Ramban Unit cost to be GP Shopian quoted 05 05 05 05 05 05 (“Group B”) 3. 4. Detailed Tender Notice No. DTE/PUR/14/ 328 Dated Electronics and communication Engineering Department Modes : Auto/ Level Source : CHI, CH II, ALT-CH I/ CH II, Ext. General Information Display : 8×10 cm Z Modulation : TTL level Power Supply : 230 V ±10 %, 50/60 Hz Included Accessories :BNC to Crocodile cable -1no.BNC to Test Prod cable -1no.Mains cord -1no.Learning material (CD) -1no. CRO Probes: 1. BNC to Crocodile cable 2. 2.BNC to BNC Digital Storage Oscilloscope: Real-time Sample Rate 500MSa/s (Single Channel).Equivalent Sample Rate 50GSa/s Number of Channels 2 CH +1 Ext Memory Depth 32Kpts (Single Channel) Acquisition Modes Normal/Average/Peak Detect Average Selectable from 4 to 256 Input Impedance 1 MV ±2% II 17 pF ±3 pF .Input Coupling DC, AC and GND Maximum Input Voltage ±400Vpp Trigger Sources CH1, CH2, Ext, Ext /5, AC Line Trigger Modes Auto, Normal, Single Trigger Type Edge, Pulse Width, Slope, Video, AlternateAuto Measure Cursor Measure Manual, Track and Auto measure mode Maths +, – , ×, /, FFT Waveform Interpolation Sin x/x, Linear Storage Internal 2 reference waveforms, 20 waveforms and 20 Setups USB BMP, CSV, Waveforms, Setups 16-10-2014 12 each 12 each 12 each 01 01 01 (“Group B”) 5. 6. Detailed Tender Notice No. DTE/PUR/14/ 328 Dated Electronics and communication Engineering Department Communication Port USB Host, USB Device, RS232, Pass/Fail Sample Types Real Time and Equivalent Time FFT Window: Hanning, Hamming, Blackman, Rectangular Persist Off, 1 sec, 2 sec, 5 sec, Infinite Measure Display Modes Main, Window, Window Zoom, Scan, X-Y Menu Display 2 sec, 5 sec, 10 sec, 20 sec, Infinite Skin Succinct Display 7 inch TFT Color LCD Display Power 100 - 240V AC, 45Hz - 440Hz, 50VA Max Accessories 1:1/10:1 Probe (2 pcs), Power Cord, USB Cable, Easy Scope Software Optional GPIB Communication Module, Serial Interface Communication Module,Pass/Fail Interface Module Frequency counter: Frequency Range : DC to 50 MHz Resolution : 1 Hz Sensitivity : 0.5 VoltsFrequency Accuracy : 0.5 % .16X2 Character LCD controlled by Microcontroller Universal IC Tester Tests a wide range of Digital IC's such as 74 Series, 40/45 Series of CMOS IC’s Microprocessor 8085, 8086, Z80, 8051, 89c51 Peripherals like 8255, 8279, 8253, 8259, 8251, 8155,6264,62256,8288,8284 Opamp,555, Transistor Arrays, Analog switches, Opto-couplers and Others 7 segment display of common cathode & common anode type Auto search facility of IC’s Test by: Truth table/sequence table comparison ZIF: 40 pin DIP ZIF sockets Keys: 28 cherry keys Key pad with numerical & functional keys Display: 9 Digit Seven Segment Display Supply Input Voltage: 230V AC 16-10-2014 03 03 03 02 02 02 (“Group B”) 7. 8. 9. 10. Detailed Tender Notice No. DTE/PUR/14/ 328 Dated Electronics and communication Engineering Department Linear IC tester Tests a wide range of Analog Ic’s such as ADC, DAC, Opamp, 555, Transistor Arrays, Analog Switches, Waveform Generator, Line Drivers, Voltages Regulators, PLL’s, VCO, PWM Generator, Sample & Hold, Voltages References, Opto couplers, Comparators, Voltages Followers and Others Test by: Truth table/sequence table comparison ZIF: 40 pin DIP ZIF sockets Keys: 50 cherry keys Key pad with numerical & functional keys Display: 16x2 Backlit LCD Display Logic Probes Logic pulser Signal Generator: Operating Modes : Sine, Square, Triangle, Ramp, Pulse, TTL and Serial Data Frequency Range : 1 Hz - 10 MHz Sine wave &1 Hz - 2 MHz others Frequency Accuracy : 0.5 % Rise & Fall time : Pulse Duty Cycle : 15 % - 85 % Variable Frequency Display : 20 x 4 character LCD Output impedance : 50 Output Voltage : 10 Vpp into 50 , 20 Vpp O.C. Attenuation : 20 dB or 40 dB fixed and 20 dB variable in between (60 dB) Frequency counter : Frequency Range : DC to 40 MHz Resolution : 1 Hz General Information : 16-10-2014 02 02 05 02 05 05 02 05 02 05 02 05 (“Group B”) Detailed Tender Notice No. DTE/PUR/14/ 328 Dated Electronics and communication Engineering Department 16-10-2014 11. 12. 13. 14. Included Accessories : BNC to BNC cable : 1 no. Mains cord : 1 no. Digital LCR-Q meter Spectrometer Wave Analyzer Analog Multimeter 03 02 01 05 03 02 01 _ 03 02 01 _ 15. Maxwells bridge kit _ _ 08 16. Andersons bridge kit _ _ 08 17. Digital Flux meter experimental kit _ _ 08 2. Principles of Communication Lab. S. NO. NAME OF ARTICLE WITH SPECIFICATION Quantity required for GP Poonch GP Ramban Unit cost to be GP Shopian quoted 1. Amplitude Modulation/ Demodulation Kit: 04 04 - 2. Frequency Modulation/ Demodulation Kit : Audio Oscillator (Message Signal):Function : Sine, Output : 0-10 VPP , Frequency : 200Hz 10 KHz, Carrier Output Frequency: Function: Sine & Cosine, Output: 0-10 VPP, Frequency: 2KHz100 KHz, FM Modulator: Armstrong Frequency Modulator, FM Demodulator: Phase Locked Loop detector, Low Pass Filter: 10 KHz cut off frequency. Output Amplifier : 1 No. with adjustable Gain 04 04 - (“Group B”) Detailed Tender Notice No. DTE/PUR/14/ 328 Dated Electronics and communication Engineering Department 16-10-2014 Test Points: 7 Nos. (Gold plated), Power Supply : 230 V ± 10%, 50Hz, Interconnections : 2 mm Banana sockets Included Accessories: Patch cord 16”: 14 nos. Mains cord: 1 no. Learning material (CD): 1 No. 3. 4. PCM Modulation Demodulation Kit: Audio codec : Stereo Inputs : Single ended Number of bits per channel : 16 bits (Left and Right) Sampling Rate : 48, 24, 12 and 6 KHz System clock : 256 x (Sampling clock) Clock Source : On-board Analog Signal Source : Sinusoidal Frequency : Up to 3.3 KHz Amplitude : 0 - 5 Vpp Power Supply : 110-220 V ± 10%, 50 /60 Hz Operating condition : 0-40 C, 80% RH Included Accessories : Patch cord 8” : 8 nos. DC Power Supply module : 1 no. Not specified Microphone : 1 no Ear Phone : 1 no. Learning material (CD) : 1 no. Delta Modulation Demodulation Kit: Input Channel : Time Division Multiplexed Serial Crystal Frequency: 6.400 MHz Sampling Clock Frequency : 50, 100, 200 & 400 KHz (Switch selectable) On board Generator :Synchronized & Adjustable Amplitude Sine Wave Generator of 1 KHz, 2 KHz, 3 KHz, 4 KHz Separate Variable DC level ,Integrator : Four integrator gain settings Normal, X 2, X 4, X 8 Low Pass Filter : Fourth order Butterworth (Cut Off Frequency 4.8 KHz) Included Accessories : 04 04 - 04 04 - (“Group B”) 5. Detailed Tender Notice No. DTE/PUR/14/ 328 Dated Electronics and communication Engineering Department Patch cords 16” (2 mm - Blue) : 14 nos. Patch cords 16” (2mm - Black) : 4 nos. Patch cords 16” (2 mm - Blue) : 1 no. DC Power Supply for DCT : 1 no. Din Cable for DC Supply : 1 no. Sampling theorem Kit 16-10-2014 04 04 - 6. PWM kit : Pulse Output (frequency) : 8kHz, 16kHz, 32kHz, 64kHz (approx.) Function Generators: Sine wave : (Gain Adjustable) , 1kHz (12Vpp),2kHz (4Vpp), Square wave : 1kHz & 2kHz (6Vpp) Low Pass Filter : 4th order BW Filter, Voice Communication : Voice Link using Dynamic Mini, Microphone & Speaker AC Amplifier : With adjustable gain control DC Variable Output : 0-12V Power Supply : 230V ±10%, 50Hz 04 04 - 7. PAM modulation Demodulation Kit : Pulse Output (frequency) : 8kHz, 16kHz, 32kHz, 64kHz (approx.) Function Generators: Sine wave : (Gain Adjustable), 1kHz (12Vpp),2kHz (4Vpp),Square wave : 1kHz & 2kHz (6Vpp) Low Pass Filter : 4th order BW Filter Voice Communication : Voice Link using Dynamic Mini,Microphone& Speaker AC Amplifier : With adjustable gain control DC Variable Output : 0-12V Power Supply : 230V ±10%, 50Hz Cathode Ray Oscilloscope (60MHz) : Operating Modes :Channel I, Channel II, Channel I &ll alternate or chopped (approximately 80MHz), X-Y operation (Ratio 1:1 Input via CH II), Add/Sub CH I ± CH II,.Invert CH II 04 04 - 02 - 8. 02 (“Group B”) Detailed Tender Notice No. DTE/PUR/14/ 328 Dated Electronics and communication Engineering Department Vertical deflection (Y) Identical channels Bandwidth : DC -60 MHz (-3 dB) Risetime : 06 ns approximately. Deflection coefficients : Microcontroller based 12 calibrated steps5 mV / cm – 20 V / cm Electronic control.Display on 32 character.backlit alphanumeric LCD. Gold plated BNC.Input coupling : DC-AC-GND.Maximum Input voltage : 400 V (DC + Peak AC) TimebaseTime coefficients : Microcontroller based 18 calibrated steps,0.5 μs/cm-0.2s/cm (1-2-5 sequence).Electronic control. Display on 32 character,backlit alphanumeric LCD. Magnifier : X10.Sawtoothout : 5 Vpp approximatelyHold-Off : Variable control for stable triggering Trigger SystemTrigger Bandwidth : 80 MHz.Modes : Auto/ Level.Source : CHI, CH II, ALTCH I/ CH II, Ext.Slope : Positive or NegativeSensitivity :Int 0.5 div., Ext 0.8 V approximately Horizontal Deflection ( X) Input via CHII. Bandwidth : DC -3 MHz (-3 dB).X-Y mode. Deflection coefficients : Microcontroller based 12 calibrated. Steps 5 mV/cm-20 V/cm(12-5 sequence) Electroniccontrol, Display on 32 characterbacklit alphanumeric display. Input : Gold plated BNCInput coupling : DC-AC-GNDMaximum Input voltage : 400 V (DC + Peak AC) Component Tester (Built – in single touch)Test Voltage : Max 8.6 V(Open)Test Current : Max 8 mA (Shorted) Test Frequency : 50 Hz, Test circuit grounded tochassis Continuity Tester :Beeper sounds General Information :Cathode Ray Tube : 140 mm Rectangular tube withinternalgraticule. Accelerating potential : 2 KV approximately. Display : 8×10 cm .Trace rotation : Adjustable on front panel .Calibrator : Square Wave generator 1KHz.approximately, 0.2 V Z Modulation: TTL levelUSB Interface : For remote control settings ofVolt/Div. & 16-10-2014 (“Group B”) Detailed Tender Notice No. DTE/PUR/14/ 328 Dated Electronics and communication Engineering Department 16-10-2014 Time/Div. Stabilized Power Supply :All operating voltages includingEHT. Power Supply :230 V ±10%, 50/60 Hz Learning Material :CD (Operating procedure, Front panel control, Theory) Included Accessories :BNC to BNC -2no. 1x/10x switchable probes -02no. Mains cord -1no. Calibration certificate -1No. Learning material (CD) -1no. 9. 10. 11. 12. CRO probes : 1.BNC to Crocodile cable 2. BNC to BNC Audio Frequency generator: Operating Modes : Sine wave & Square wave.Frequency Range : 10 Hz - 100 KHz, in suitable decade steps. Frequency : 4 digit 7-segment LED display.Accuracy :±1 Digit.Amplitude : 3 digit 7 segment LED display General Information Mains Supply : 220 V ±15 %, 50 Hz .Power Consumption : 12 VA (approx.) Included Accessories BNC to BNC cable, Mains cord, Learning material (CD) - 1 no. AM square law modulator Demodulator Kit Signal Generator with digital display Operating Modes :Sine, Square, Triangle, DC. Free running or external frequency modulated, with or without DC offset.Frequency Range : 0.1 Hz - 1 MHz in 7 decade steps, variablecontrol between steps .Frequency Range and Mode : Microcontroller based Selection 10 10 - 03 03 - 02 02 - 03 03 - (“Group B”) Detailed Tender Notice No. DTE/PUR/14/ 328 Dated Electronics and communication Engineering Department 16-10-2014 Waveform Characteristics Sine Wave Distortion : 0.1 Hz to 100 KHz : max.0.5% 100 KHz to 500 KHz : max. 1.5% 500 KHz to 1 MHz : max. 3% Square Wave Risetime : max. 70 ns. (10 to 90 %) Display.. LCD display Outputs Signal Output : (short-circuit proof) BNC (Gold plated) Impedance : 50  / 600  switchable Output Voltage : Max.15 Vpp into 50  , 30 Vpp open circuit DC Offset :12.5 V adjustable Trigger Output : TTL more than 4 V, CMOS level adjustable upto 14 V approx.FM Input / External SweepFrequency Change : approx. 1 : 100Input Impedance : 100 K II 25 pF Input Voltage : max. ±30 V Frequency Counter:Frequency Range : DC to 50 MHz, Resolution : 1 Hz 13. Double balanced modulator/demodulator kit _ _ 6 14. Frequency modulator /demodulator kit _ _ 6 15. Computing the locking range of PLL kit _ _ 6 16. Frequency demodulation IC based kit _ _ 6 17. Sample and hold function for digital study kit _ _ 6 18. IF amplifier IC based _ _ 6 19. Frequency synthesizer _ _ 6 (“Group B”) 3. Detailed Tender Notice No. DTE/PUR/14/ 328 Dated Electronics and communication Engineering Department 16-10-2014 Digital Electronics Lab. S. NO. NAME OF ARTICLE WITH SPECIFICATION Quantity required for GP Poonch GP Ramban GP Shopian 1. Expt. Board for verification and interpretation of truth table for AND, OR, NOT, NAND, NOR, XOR, XNOR, Gates. 02 02 _ 2. Expt. Board for construction of Half Adder using gates. 02 02 _ 3. Expt. Board for construction of Full Adder using gates 02 02 _ 4. Expt. Board for verification operation of a 8- bit D/A converter. 02 02 _ 5. 4 bit adder, 2’s compliment subtractorckt using and 4 bit adder IC and an XOR IC kit to verify its operation 02 02 _ 6. Kit to verify the truth table for +ve edge triggered, -ve edge triggered, level triggered IC flip flops (at 03 least one IC each of D latch, D flip flop, JK flip flop) 03 _ 7. Kit to verify the truth table for encoder and decoder IC’s, mux and DeMux. 02 02 _ 8. Kit to design a 4 bit SISO, SIPO, PISO, PIPO shift registers using JK/D flip flop and to verify their operation. 02 02 _ 9. Kit to design 4 bit ring counter and to verify its operation. 02 02 _ 10. Kit Of Asynchronous counter IC’s for verification of truth table of universal shift register IC using 02 02 02 Unit cost to be quoted (“Group B”) Detailed Tender Notice No. DTE/PUR/14/ 328 Dated Electronics and communication Engineering Department 16-10-2014 IC 7490 / 7493 or equivalent TTL a) b) c) d) 4. Divide by 2 Divide by8 Divide by 10 Divide by 16 11. Basic digital Electronics kit 12. 4 bit adder and subtractor kit 13. Flip flop kit 14. Multiplexer de-multiplexer kit 15. Digital frequency meter/universal counter/timer experimental kit 16. Logic probes TTL and CMOS 17. Logic trainer boards 18. Universal programmer 19. EPROM programmer 20. EPROM eraser Electronic Design and Fabrication Technique Lab. S. NO. NAME OF ARTICLE WITH SPECIFICATION _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 02 02 02 02 02 02 10 01 01 01 Quantity required for GP Poonch GP Ramban GP Shopian Unit cost to be quoted (“Group B”) 1. 2. Detailed Tender Notice No. DTE/PUR/14/ 328 Dated Electronics and communication Engineering Department Soldering Station Soldering Power consumption 60 WInput voltage 170 to 270 V Temperature range 180 to 270VTemp stability  10C Temp accuracy  1C of tolerance at idling timeTip to ground potential under 2 mV Tip to ground resistance under 2 Ohms Desoldering70 Watts Input 170 to 270 V ACTemp range 180 to 480CPump diaphragm typeVacuum 600 mm/Hg Soldering &Desoldering1. Unit2. Complete Soldering Handle 01 No.3. Complete Desoldering Handle 01 No.4. Stand Soldering 01 No.5. Stand Desoldering 01 No.6. Sponge 02 No.7. FibreFilters(Primary/Small) 01 No.(Secondry/ Big) 01 No. 8. Cleaning Springs 01 No.9. Glass Tubes 01 No.10. Mains Cord 01 No. PCB Design & Fabrication complete Setup. 1) PCB Art Work Film Maker This is a table top unit which serves as contact printer for developing thefilms. The films are used for further PCB development. Supply : 230V AC ± 10%, 50Hz Operating Mode : Manual / Automatic Timer : Adjustable from 1 Sec to 10 Sec with 1 sec interval Display : 16 x 2 LCD for timer and lamp status display Exposing area : 20” x 10” Buzzer : For timer indication Lamp indicator : Status of internal exposing lamp 2) Artwork Table 16-10-2014 02 02 01 _ _ _ (“Group B”) Detailed Tender Notice No. DTE/PUR/14/ 328 Dated Electronics and communication Engineering Department This is a table top artwork and PCB inspection table with illumination lamp.This unit is used for art work designing and PCB corrections. This can alsobe used for designing small circuits. The illumination lamp providesuniform light which is helpful in artwork by providing better light for workingenvironment. Supply : 230V AC ± 10%, 50Hz Light Exposed area : 17” x 13” 3) PCB Shearing Machine This machine is provided for cutting the PCB. This machine cuts the PCB with good efficiency and accuracy. Mounting Base : Table Mounted / Floor Mounted Cutting Area : 12” 4) Photo Resist Dip Coating Machine The machine is table top and designed for the coating of Photoresist on the PCB Laminate. The Photoresist is used to cover the PCB Laminate Copper surface for further chemical development. This Photoresist is sensitive to Ultra Violet light. Supply : 230V AC ± 10%, 50Hz Timer : Adjustable from 1 Sec to 30 Sec at interval of 5 sec. Display : 16 x 2 LCD for timer Buzzer : For timer indication Dipping area : 12” x 10” Spreading Science & Technology for a Better World 5) UV Exposure Unit This is a table top unit provided for the Photoresist coated PCB exposing. This unit is used for exposing the PCB. The PCB which is coated with the Photoresist is placed along with the film in this unit. This unit exposes the film on the PCB. 16-10-2014 (“Group B”) Detailed Tender Notice No. DTE/PUR/14/ 328 Dated Electronics and communication Engineering Department Supply : 230V AC ± 10%, 50Hz Operating Mode : Manual / Automatic Timer : Adjustable from 1 Sec to 20 min. Display : 16 x 2 LCD for timer and lamp status display Exposing area : 20” x 10” Buzzer : For timer indication Lamp indicator : Status of internal exposing lamp. 6) Dye Tank This is a table top unit provided for dye coating on PCB. This unit is responsible for the visibility of the design on the PCB. This tank is filled with a solution which darkens the remaining Photoresist on the PCB. This machine highlights the design on the PCB. Supply : 230V AC ± 10%, 50Hz Timer : Adjustable from 1 Sec to 30 Sec at interval of 5 sec. Display : 16 x 2 LCD for timer Buzzer : For timer indication Dipping area : 12” x 10” 7) Development Tank This is a table top unit which is provided for development of PCB. This unit is responsible for removing unused Photoresist from the PCB after the UV exposure. This tank is filled with chemical which removes unused Photoresist. Supply : 230V AC ± 10%, 50Hz Timer : Adjustable from 1 Sec to 30 Sec at interval of 5 sec. Display : 16 x 2 LCD for timer Buzzer : For timer indication Spreading Science & Technology for a Better World 8) PCB Etching Machine 16-10-2014 (“Group B”) Detailed Tender Notice No. DTE/PUR/14/ 328 Dated Electronics and communication Engineering Department This is a table top unit for the etching of PCBs. This unit removes the unused copper from the PCB. This removal is carried by a chemical process which takes place in the machine. Motor : 1/16 HP Pressure pump Dipping area : 12” x 10” Mains Supply : 230V ±10%, 50Hz 9) Drill Machine The drill machine is used for making drills in the PCB. This is provided with different size of drill bits for making drills in the PCB. Supply : 230V AC ± 10%, 50Hz RPM : 1500 which are adjustable in steps. Drill bits : 0.8mm - 5 Nos. 1.0 mm - 5 Nos. 10) Solderable Lacquer This is a table top unit which is used for protecting the PCB from environment. This chemical coated on PCB ensures protection for long time. Supply : 230V AC ± 10%, 50Hz Timer : Adjustable from 1 Sec to 30 Sec at interval of 5 sec. Display : 16 x 2 LCD for timer. Buzzer : For timer indication Dipping area : 12” x 10” 10) PCB Designer Kit This kit includes tapes stencils which are helpful in designing the PCB. CONTENTS: 1. Rotring Pens 16-10-2014 (“Group B”) Detailed Tender Notice No. DTE/PUR/14/ 328 Dated Electronics and communication Engineering Department 2. Marker Pens 3. Magnifying Lens 4. Ruler 5. Stencils 6. Cutter 7. Adhesive Tape 8. Scrubber 9. Cleaning reagent 12) PCB Curing Machine The PCB curing machine is used for curing the PCB Laminate after Photoresist coating. The curing machine is equipped with a hot air blower with auto cutoff facility. Type : Blower Supply : 230 V / 50 Hz Heating area : 12” x 12” Spreading Science & Technology for a Better World89 Accessories All the accessories required given below . 1. Tray : 5 Nos 2. Brush : 2 Nos 3. PCB Laminate : 10 Nos 4. Measuring Flask : 250 ml 5. Clips : 10 Nos 6. Hand Gloves : 2 Pairs PCB lab necessary chemicals which are required for PCB designing 1. 2. 3. 4. 5. 6. LPR Photoresist negative= 4 Ltr LPR Thinner= 4 Ltr Developer =10 Ltr Dye Blue =10 Ltr Cleaning Reagent 1 (alcohol) =2 Ltr Cleaning Reagent 2 (Thinner) =2 Ltr 16-10-2014 (“Group B”) 3. 4. 5. 6. 7. Detailed Tender Notice No. DTE/PUR/14/ 328 Dated Electronics and communication Engineering Department 7. Solderable Lacquer= 2 Ltr 8. Developer Part A= 500 gm 9. Developer Part B= 500 gm 10. Lith Film Fixer= 500 gm 11. FeCl3 =5 Kg Distilled Water= 5 Ltr Grinder 0.5 HP with different grinding plates and accessories Circular saw Simple Soldering stations temperature controlled High speed PCB drilling machine with complete drill bit sets, tabletop, motor speed20,000 rpm, range 0.6 to 3.0 mm, working area 280 mmx170mm Ammonia etching machine for single and double sided PCBs (2 bar oscillating spray system, max. board size 250x 300 mm 16-10-2014 - - 1 1 10 01 - - 01 5. Electronics Devices and Circuits Lab. S. NO. NAME OF ARTICLE WITH SPECIFICATION Quantity required for GP Poonch GP Ramban GP Shopian 1. Single Stage RC coupled Amplifier Kit 03 03 05 2. 2- Stage RC coupled Amplifier Kit 03 03 04 3. Push Pull Amplifier Kit 03 03 05 4. Emitter Follower Kit 03 03 05 5. Colpitts Oscillator Kit 03 03 05 Unit cost to be quoted (“Group B”) Detailed Tender Notice No. DTE/PUR/14/ 328 Dated Electronics and communication Engineering Department 16-10-2014 6. Hartley Oscillator Kit 03 03 05 7. phase shift ossilator Kit 03 03 05 8. Wein bridge Oscillator Kit 03 03 05 9. Multiviberator kit using IC 555(Astable , Monostable, Bistable modes) 02 02 - 10. Operational Amplifier Complete Kit using IC 741 (Adder ,Subtractor, integrator , Differentiator, Comparator etc. ) on a single KIT 03 03 06 11. D.C regulated Power Supply DC Output : A : 0-30 V, 1 A and B : 5 V, 1 A Output A DC Output : 0-30 V, continuously variable by meansof Coarse and Fine controls.Output Current : 1 A (max) Setting Resolution : Voltage : 10 mV.Current : 2 mAInternal Resistance =15 mΩ.Stability : 2.5 mV Display : 3 digit for voltage and 3½ digit for currentAccuracy : ± (1% + 1 digit) Over Range Indication : By flashing mA LED indication .Overload indication : Audible beeping Output B DC Output : 5V Fixed (Screw driver adjustment between4.8 V to 5.2 V) Output Current : 1A (maximum) Load & Line Regulation : ± (0.05%+10 mV) Temperature Coefficient : ± (0.05% + 5 mV/0C) Over Range Indication : By LED indication & audible beeping Power Supply : 230V ± 10%, 50/60Hz Included Accessories Mains cord : 1 no. 04 04 10 (“Group B”) Detailed Tender Notice No. DTE/PUR/14/ 328 Dated Electronics and communication Engineering Department 16-10-2014 13. Learning material CD : 1 no. Multiple DC power supply DC Output : A : 0-30 V, 1 A continuously variable by means of Coarse & Fine controls B : 5 V, 1 A Adjustable from 4 V - 6 V C : 0 - ± 15 V, 1 A adjustable by means ofCoarse& Fine controls Current Limit : 20 mA - 1 A, Adjustable Resolution : Voltage : 100 mV Current : 10 mA Display : 3 digit for voltage and 3½ digit for current, LED indication for Voltage and Current LEDs indicate Overload Included Accessories Mains cord : 1 no. Learning material (CD) : 1 no. Clipper and clamping Circuit Kit 14. Expt. Board for 1)clipping of both portion of sine wave using:a)Diode and DC Source b)Zener diode 2)For Clamping a sine wave tp a)Negative DC voltage . b)Positive Dc voltage with built in supply and provision for inputs and outputs. Audio oscillator kit - - 04 15. Wideband RC oscillator - - 04 12. 02 02 04 04 04 05 (“Group B”) Detailed Tender Notice No. DTE/PUR/14/ 328 Dated Electronics and communication Engineering Department 16-10-2014 16. Function generator 500 KHz - - 10 17. Single trace CRO 20 MHz with accessories - - 04 18. Dual trace CROs 50 MHz with accessories - - 12 19. Mains voltage stabilizer 3 KVA single phase - - 04 20. AC millivotmeters range 1mV,10 mV,100mV,1000mV - - 05 each 21. DC millivotmeters range 1mV,10 mV,100mV,1000mV - - 05 each 22. AC voltmeter range 10v,250v,300v,500v - - 05 each 23. DC ammeter range 1A,10 A - - 05 each 24. Distortion factor meter 20 KHz, attenuation 20 dB to -10dB - - 02 25. Transducers: pressure type, thermocouple, LVDT, opto pick-up ,magnetic pick up. - - 02 each 26. Digital thermometer 0-300degree C - - 01 27. Digital lux meter - - 01 28. Rectifier kits(half wave, full wave bridge and centre tapped) - - 06 29. Rectifier filter circuit - - 06 30. Transistor CB and CE configuration - - 06 each (“Group B”) S. NO. Detailed Tender Notice No. DTE/PUR/14/ 328 Dated Electronics and communication Engineering Department 6. NETWORK FILTERS AND TRANSMISSION LINES LAB. NAME OF ARTICLE WITH SPECIFICATION 16-10-2014 Quantity required for GP Poonch GP Ramban GP Shopian 1. Characteristic impedance of symmetrical T and Л network experimental Kit 04 04 04 2. Image impedance of a given asymmetrical T and Л networks experimental Kit 04 04 04 3. Prototype low pass filter experimental Kit to determine 04 04 04 a) Characteristic impedance b) attenuation c) Cut- off Frequency 4. Symmetrical T/ Л type attenuator experimental Kit To determine Attenuation 04 04 04 5. Prototype high pass filter experimental Kit to determine 04 04 04 04 04 04 04 04 04 6. 7. a) characteristic impedance b) attenuation c) Cut- off frequency Prototype band-pass filter experimental Kit to determine a) characteristic Impedance b) attenuation c) Cut-off frequency m- derived low pass filter and High pass filter experimental Kit to determine a) characteristic Impedance b) attenuation c) Cut- off frequency Unit cost to be quoted (“Group B”) Detailed Tender Notice No. DTE/PUR/14/ 328 Dated Electronics and communication Engineering Department 16-10-2014 d) Attenuation or infinity frequemcy. 8. Crystal filter experimental Kit to determine attenuation 02 02 - 9. Transmission line standard experimental Kit to determine 03 03 - SWR and characteristic impedance of the line. 10. Signal Generator: Operating Modes: Sine, Square, Triangle, Ramp, Pulse, TTL and Serial Data, Frequency Range : 1 Hz - 10 MHz Sine wave & 1 Hz - 2 MHz others. Frequency Display : 20 x 4 character LCD Output impedance : 50,Output Voltage : 10 Vpp into 50 , 20 Vpp Frequency counter : Frequency Range : DC to 40 MHz, Resolution : 1 Hz, Sensitivity : 0.5 Vrms, Input Impedance Included Accessories : BNC to BNC cable : 1 no. Mains cord : 1 no. Learning material (CD) : 1 no. 01 01 - 11. SWR meter 03 03 - 7. COMMUNICATION SYSTEMS-I LAB. S. NO. NAME OF ARTICLE WITH SPECIFICATION Quantity required for GP Poonch GP Ramban GP Unit cost to be quoted (“Group B”) Detailed Tender Notice No. DTE/PUR/14/ 328 Dated Electronics and communication Engineering Department 16-10-2014 Shopian 1. AM transmitter Audio Oscillator : With adjustable Amplitude & Frequency (300 Hz - 3.4 KHz) Audio Output : Amplifier with speaker Modulators: Balanced Modulator with Band pass Filter (1 MHz) - 2 nos. Balanced Modulator: 1 No. (455 KHz) Ceramic BandpassFilter : 1 No. (455 KHz) Carrier Frequency : 1 MHz (Oscillator controlled) Transmitter Amplifier Output: (Gain adjustable) DSB (1 MHz), SSB (1.445 MHz) connected to Antenna/cable Switched Faults : 8 nos. Interconnections : 2mm Banana socket Test Points : 27 nos Power Supply : 110-220 V AC ±10%, 50/60Hz Included Accessories : Patch Cord 16" : 2 nos. Mains Cord : 1 no. TechBook Power Supply : 1 no. Microphone : 1 no,Earphone : 1 no. 02 02 2. Radio Receiver Construction : Superhetrodyne Frequency Range : 980 KHz to 2060 KHz, Intermediate Frequency : 455 KHz Input Circuits : 1) RF Amplifier 2) Mixer 3) Local Oscillator 4) Beat Frequency Oscillator 5) IF Amplifier 1 6) IF Amplifier 2 Tuning : With variable capacitor (ganged) Dial marking on board Receiving media : Telescopic antenna / Cable 02 02 - 04 - (“Group B”) Detailed Tender Notice No. DTE/PUR/14/ 328 Dated Electronics and communication Engineering Department 16-10-2014 Detectors: 1) Diode detector (for DSB) 2) Product detector (for SSB) Audio Output : Amplifier with speaker Automatic Gain Control : Switchable Switched Faults : 8 nos. Interconnections : 2 mm Banana sockets Test points : 30 nos. Power Supply : 110-220 V AC ±10%, 50/60Hz Included Accessories : Patch cord 16" : 2 nos. Tech Book Power Supply : 1 no. Mains cord : 1 no. Earphone : 1 no. 3. AM broadcast radio receiver experimental setup 02 02 - 4. Antenna training System RF generator : 550 to 850 MHz approximately (with level adjust) Modulation Generator : 1 KHz approximately (300 mV) Directional Coupler : Forward & Reverse (On board selectable) Matching Stub : Slide Stub Antenna Rotation : 0- 360 Degree, Resolution 1 Degree Transmitting & Receiver masts provided Receiving antenna : Folded Dipole with reflector Detector Display : Adjustable meter Interconnections : BNC Power Supply : 230 V ±10%, 50/60 Hz Learning material : procedure, reference results booklet Fiber optic Kit Transmitter : 1 no., Fiber Optic LED having peak wavelength of emission 660 nm 02 02 - 03 03 5. - (“Group B”) Detailed Tender Notice No. DTE/PUR/14/ 328 Dated Electronics and communication Engineering Department Receiver : 1 no., Fiber Optic Photo detector Modulation Techniques : 1. AM 2. FM 3. PWM Drivers : 1 no. with Analog & Digital modes Clock : Crystal controlled Clock 4.096 MHz PLL Detector : 1 no. AC Amplifier : 1 no. Comparator : 1 no. Filters : 1 no. 4th order Butterworth, 3.4 KHz cut-off frequency Analog Band Width : 350 KHz Digital Band Width : 2.5 MHz Function Generator : 1 KHz Sine wave (Amplitude adjustable) 1 KHz Square wave (TTL) Clock Generator : 64 KHz/128 KHz/256 KHz (TTL) Data Generator : 15 Bit Noise Generator : Variable level Bit Error Counter : 4 digits, 7 segment display Voice Link : F. O. voice link using microphone & speaker (built in) Switched Faults : 4 in Transmitter & 4 in Receiver Fiber Optic Cable : Connector type Standard SMA Cable Type : Step indexed multimode PMMA plastic cable Fiber Diameter : 1000 microns Fiber Length : 0.5 m & 1 m Test Points : 34 nos (Gold plated) Inter connections : 2 mm sockets Power Supply : 110-220 V, ±10%, 50/60 Hz Learning Material : CD (Theory, procedure, reference results, etc). Included Accessories : Learning material (CD), NA measurement jig, Mandrel, Fiber cables, Microphone, Headphone, Set of Patch cords 16-10-2014 (“Group B”) Detailed Tender Notice No. DTE/PUR/14/ 328 Dated Electronics and communication Engineering Department 16-10-2014 Accessories : 5 meter fiber cable, 10 meter fiber cable. 8. POWER ELECTRONICS LAB. S. NO. 1. 2. 3. NAME OF ARTICLE WITH SPECIFICATION SCR characteristic Kit Mains supply 230V ±10%, 50Hz DC power supply +35V, +15V, 250mA Voltmeter 0-35V (max.) Ammeter 0-50mA (max.) TRIAC characteristic Kit Mains Supply : 230 V ± 10%, 50 Hz Power Supply : +35 V DC (250 mA),- 35 V DC (250 mA),15 V DC (250 mA) Fuse : 500 mA Voltmeter : 50 V DC Ammeter : 50 mA DC DIAC characteristic Kit Mains Supply : 230V ± 10%, 50Hz Power Supply : +35V DC (250mA) -35V DC (250mA) Fuse : 500mA Voltmeter : 50V DC Ammeter : 50mA DC Quantity required for GP Poonch GP Ramban GP Shopian 04 04 05 04 04 05 04 04 05 Unit cost to be quoted (“Group B”) Detailed Tender Notice No. DTE/PUR/14/ 328 Dated Electronics and communication Engineering Department 16-10-2014 4. UJT characteristic Kit 03 02 - 5. UJT relaxation oscillator experimental Kit. 04 04 - 6. Single-phase half wave controlled rectifier experimental Kit. 04 04 02 7. Single phase full wave controlled rectifier experimental Kit 04 04 02 8. TRIAC based AC phase control Experimental Kit for Varying lamp intensity and AC fan speed control 03 03 02 9. Power Supply Training System using ICs 78xx and 79xx series 02 02 - 10. Input : 230 V ±10%, 50 Hz Outputs Zener diode outputs : 10 V, 5.6 V regulated Regulators outputs : +12 V regulated -12 V regulated,1.8 to 17 V adjustable Load : 5 K variable with 100 W fixed resistance Bleeder Resistor : 5 K variable with 100 W fixed resistance AstableMultivibrator : 1 Hz, 14 Vpp Transformer : Primary 0 to 220 V ,Secondary 18-0-18, 6-0-6 (500 mA) Fuse : 500 mA (slow blow, spare fuse is given in mains socket) DC chopper with firing module 50V,2A - - 02 11. Bridge converters power and firing module - - 02 12. Single phase inverter firing module for SCR using UJT - - 02 13. Speed control of DC motors using SCR kit - - 02 (“Group B”) Detailed Tender Notice No. DTE/PUR/14/ 328 Dated Electronics and communication Engineering Department 16-10-2014 14. Chopper circuit experimental kit - - 04 15. Relay demonstration panel - - 01 9. MICROPROCESSOR LAB. S. NO. 1. 2. NAME OF ARTICLE WITH SPECIFICATION 8085 Microprocessor Experimental Kit Operating Frequency : 6.144 MHz ROM : 8 K RAM : 8 K Input : ASCII Keyboard Display : 20 X 2 LCD Power Supply : 110V - 260V AC, 50/60Hz Diagrammatic representation of full system Three channel Timer/Counter using 8253 24 I/O lines provided through 8255 22 I/O lines provided through 8155 Two modes of command HEX key pad mode, Serial mode Facility of downloading and uploading the files from PC All Address and Data lines are provided on 50 pin connector Battery Backup for RAM Learning material CD 8085 Microprocessor Experimental Kit Operating Frequency : 6.144MHz Quantity required for GP Poonch GP Ramban GP Shopian 10 10 - 10 10 - Unit cost to be quoted (“Group B”) Detailed Tender Notice No. DTE/PUR/14/ 328 Dated Electronics and communication Engineering Department 16-10-2014 RAM : 8K&ROM : 8K Input : 7 x 4 HEX keypad Display : Seven segment Mains supply : 90 - 230V AC, 50Hz Diagrammatic representation of full system Powerful monitor program, Battery backup for RAM Three channel Timer/counter using 8253, 48 I/O lines using 8255 On board EPROM programmer for 27 series, On board 8 channel ADC & DAC Facility of downloading and uploading the files from PC. Two command mode interface (a) ASCII Keyboard (b) Serial Mode All Address and Control lines are available on 50 pin Connector Learning Material : (Theory, procedure, reference results etc) 10. S. NO. 1. ELECTRICAL MACHINES LAB. NAME OF ARTICLE WITH SPECIFICATION Power measurement by Two wattmeter method KIT Mains Supply : Three Phase, 415V ±10%, 50Hz Load : R - L Analog Meters Used Wattmeter : 500W (2 Nos.) Voltmeter (MI) : 500V Ammeter (MI) : 1A Quantity required for GP Poonch GP Ramban 01 01 GP Shopian - Unit cost to be quoted (“Group B”) 2. 3. 4. Detailed Tender Notice No. DTE/PUR/14/ 328 Dated Electronics and communication Engineering Department MCB (TPN) : 10 Digital workstation Size of Breadboard : 172.5 mm x 128.5mm DC power supply: +5 V, lA, 500 mA Amplitude : 3.3V (TTL) Duty cycle : 50 %, TTL output Pulsar Switches :2 Nos. Data switches :8 Nos. (Toggle switches for both TTL modes) LED display :8 Nos. (TTL) Seven Segment Display :3 Nos. Power Supply : 100V - 240V AC, 50/60Hz Learning Material : C D ( T h e o r y , p r o c e d u re rereference results, etc), DC Power Supply workstation Power supply = +12 V (200 mA), -12 V (200 mA), +5 V (200 mA), -5 V (200 mA) Solder less bread board with 1685 tie points Power Supply : 220/110 V, 50/60 Hz Included Accessories : Bread board : 2 nos. 2mm to 1mm patch cord : 5 nos. Mains cord : 1 no. 3-Phase 5KW, 400V, 50 Hz Variable RL-Load (Three Phases and 1 Neutral) 2- terminals of each phase should be brought on the panel. Switches should be on the panel for varying RL- Load. Voltmeter 0-500V 2 No. Ammeter 0-5 A 2 No. 16-10-2014 03 03 - 03 03 - 01 01 - (“Group B”) Wattmeter 5. 6. Detailed Tender Notice No. DTE/PUR/14/ 328 Dated Electronics and communication Engineering Department 16-10-2014 2 No. Single phase transformer with terminals of primary and secondary on the Panel . Mains Supply : Single Phase, 230V AC ±10%, 50Hz Single Phase Transformer Rating : 1kVA Primary Voltage : 0-125V, 0-125V Secondary Voltage : 0-125V, 0-125V Rated Current : 5A Single Phase Auto Transformer Primary Voltage : 230V Secondary Voltage : 0-270V Rated Current : 5A Analog Meters Used Voltmeter (MI) : 300V (2 Nos.) Voltmeter (MI) : 50V Ammeter (MI) : 5A (2 Nos.) Ammeter (MI) : 1A Wattmeter : 100W Wattmeter : 1000W MCB (SP) : 6A Complete panel of DC shunt motor 5 KW (with Loading arrangement), 220 V, 4 Pole with 3 point starter and to run the motor at different speeds with the help of field regulator and armature control at no- load, ¼ load, ½ load, ¾ load and full load ( i.e. at different load conditions). The panel must have the provision to provide 220 V d.c supply for armature as well as 01 01 - 01 01 - (“Group B”) Detailed Tender Notice No. DTE/PUR/14/ 328 Dated Electronics and communication Engineering Department 16-10-2014 field regulator. 7. 5 H.P Three phase squirrel cage induction motor (Star- Delta starter) with complete panel 01 ( proper Loading arrangement, 2 Wattmeter, voltmeter, ammeter required as per specification) to measure the efficiency, power factor, full load current, no load current and must have provision to change the direction of rotation of the motor. The panel must have provision to perform no load and blocked rotor test 01 - 8. Single phase induction motor with Complete Panel Mains Supply : Single Phase, 230V ±10%, 50Hz Single Phase Induction Motor Type : Capacitor start Rating : 1HP (Also available with 2HP) Voltage rating : 230V ±10% Speed : 1440 RPM (No Load) Insulation : Class ‘B’ Loading Arrangement : Mechanical Brake drum/Pulley : Aluminum Casted Analog Meters Used Voltmeter (MI) : 0 - 300V Ammeter (MI) : 0 - 10A Wattmeter : 1500W MCB (SP) : 10A Tachometer : 20,000 RPM Three phase Synchronous motor with complete panel Mains Supply : Three Phase, 415V±10%, 50Hz Machines Specification (2 Nos.) Both the Machines are flexibly coupled and mounted on a M.S. channel base 01 01 - 01 01 - 9. (“Group B”) Detailed Tender Notice No. DTE/PUR/14/ 328 Dated Electronics and communication Engineering Department 16-10-2014 10. Three Phase Synchronous Motor Type : Salient Pole Rating : 3 HP Voltage rating : 415V ±10% Speed : 1500 RPM Insulation : Class ‘B’ Excitation Voltage : 120V DC Machine (Acts as generator) Type : Shunt Rating : 2 HP Voltage Rating : 200V Speed : 1500 RPM (no load) Insulation : Class 'B' Analog Meters Used AC Ammeter (MI type) : 10A DC Ammeter (MC Type) : 2A AC Voltmeter (MI type) : 500V DC Voltmeter (MC Type) : 300V Wattmeter : 1500 - 0- 1500W (2 Nos. ) MCB (TPN) : 10A Stepper motor 01 01 - 11. Digital Tachometer 01 01 - (“Group B”) Detailed Tender Notice No. DTE/PUR/14/ 328 Dated Electronics and communication Engineering Department 16-10-2014 12. Three Phase Variac 20 A 02 02 - 13. Single Phase Variac 15 A 01 01 - 14. DC coupled generator 5 KW coupled with three phase slip ring induction motor complete with panel and accessories 01 01 - 15. Frequency Meter (Digital ) 02 02 - 16. AC servo motor (1HP) 01 01 -