Digilink Dlc450 - Hd-sdi Video-over-ip Gateway Quick Start Guide Module Settings Configuration

Transcript

QUICK START GUIDE DigiLink DLC450 - HD-SDI Video-Over-IP Gateway Module Settings Configuration 1 2 1 Operational Mode Set to either TX or RX depending on mode required 2 IP Address of Module IP address that Module uses to respond to Pings 3 Video Alarm ENABLE ALARM on loss of active video 4 SFP Alarm ENABLE ALARM on SFP not present Receiver Settings Configuration 3 1 Source IP IP address that Module uses in unicast mode to receive from 2 Multicast Group Multicast IP Address that Module uses when in Multicast Mode 3 Port Port number setting must match the Port number setting on the TX module that you wish to receive video data from 4 Recovery Buffer Specifies Data Latency Time from Ethernet in to SDI TX out. Sm setting: latency is 100ms, Lg setting: delay is 120ms 4 Transmitter Settings Configuration Sets which input port for HD SDI video to In BNC 1 Video Source 1 or available backplane inputs 2 3 4 2 Destination IP Address Destination Address which module is transmitting to 3 Port Port number setting must match the Port number setting on the RX module that you wish to transmit the video data to 4 Time to Live Not applicable at this time FEC Mode Specifies Forward Error Correction (FEC) settings • Specify Column or Row/Column or No FEC • Specify FEC matrix (row and column) size (maximum 3000) 5 1 2 3 4 5 DLC450 Front Panel: • Mon HD-BNC - In TX mode, this BNC outputs a copy of the HD SDI signal received on the BNC in connecter. In RX mode , this BNC outputs a copy of the HD SDI signal sent out the BNC out. • RST Pushbutton - Pressing, holding in for more than 4 seconds and then releasing this button will reset the module. Reset is similar to power-up sequence of module. No user configuration data is changed during this reset. • Select Pushbutton - Not used, for future use. DigiLink DLC450 - HD-SDI Video-Over-IP Gateway DLC450 FRONT PANEL LEDS LED Function OK Module Status TX RX A Link B Link Transmitter Mode Indicator Receiver Mode Indicator SFP Link Not Used Color Description OFF No power or if power is applied to the system, an internal fault with the DLC450 may exist. n Green Normal operation. n Yellow Minor alarm. n Red Major alarm. OFF Receiver mode is selected. n Green TX Mode: Valid HD-SDI detected. n Yellow TX Mode: No HD-SDI detected. n Red TX Mode: Configuration error. Invalid SDI format received OFF Transmitter mode is selected. n Green RX Mode: Valid HD-SDI detected. n Yellow RX Mode: No HD-SDI video lock detected. n Red RX Mode: No Video and CRC Errors.  Red RX Mode: Valid Video with CRC Errors. OFF No SFP installed or SFP disabled. n Green Link established.  Green Data activity on link.  Yellow RX optical power high. n Red RX low optical power or SFP fault. Ethernet link down.  Red RX low optical power or SFP fault. Off Not used, for future use. DLC450 REAR PANEL LEDS LED Function OK Module Status TX ENC RX DEC SFP A TX SFP A RX Transmitter Mode Indicator Receiver Mode Indicator SFP Transmit SFP Receive Color Description OFF No power or if power is applied to the system, an internal fault with the DLC450 may exist. n Green Normal operation. n Yellow Minor alarm. n Red Major alarm. OFF Receiver mode is selected. n Green TX Mode: Valid HD-SDI detected. n Yellow TX Mode: No HD-SDI detected. n Red TX Mode: Configuration error. Invalid SDI format received OFF Transmitter mode is selected. n Green RX Mode: Valid HD-SDI detected. n Yellow RX Mode: No HD-SDI video lock detected. n Red RX Mode: No video and CRC errors.  Red RX Mode: Valid video with CRC errors. OFF No SFP installed or disabled n Green Normal operation n Red SFP TX Fault OFF No SFP installed or SFP disabled. n Green Link established with no activity  Green Link established with data activity  Yellow RX optical power high. n Red RX low optical power or SFP fault. Ethernet link down.  Red RX low optical power or SFP fault. SFP B TX Not Used OFF Not used, for future use. SFP B RX Not Used OFF Not used, for future use.  Flashing green |  Flashing yellow |  Flashing red Install SFP+s Install an Artel SFP+ in socket A only. Socket B is for future use. AR208-008450-B00_D Sales T: 978-263-5775 www.artel.com [email protected] [email protected]