Dimensioned Drawing Electrical Connection Odsl 8 Optical Laser

Transcript

ODSL 8 Optical laser distance sensors Art. Nr. 501 09345 Dimensioned drawing 25 … 45mm 18 - 30 V DC z Reflection-independent distance information z Highly insensitive to extraneous light z Analogue current and voltage output z Measurement range and mode adjustable z Teachable switching output z M12 turning connector A B C D E F Receiver Transmitter Optical axis 90° turning connector LED yellow, green Reference edge for the measurement (cover glass) We reserve the right to make changes • ods_21gb.fm Electrical connection IEC 60947... IEC 60947... IP 69K IP 67 Accessories: (available separately) z z z z z Mounting systems Configuration adaptor UPG 5 Configuration software Cable with M12 connector (K-D …) Control guard Leuze electronic GmbH + Co. KG [email protected] • www.leuze.com In der Braike 1 D-73277 Owen Tel. +49 (0) 7021 573-0 ODSL 8/V4-45-S12 - 05 ODSL 8 Specifications Tables Optical data Measurement range 1) Resolution Light source Wavelength Light spot Laser warning notice 25 … 45mm 0.01mm laser 650nm (visible red light) divergent, 1x6mm2 at 45mm see remarks Error limits (relative to measurement distance) Absolute measurement accuracy 1) Repeatability 2) b/w detection thresh. (6 … 90% rem.) 0.5% 0.1% ≤ 0.5% Timing Measurement time Response time Delay before start-up 2 … 5ms ≤ 150ms ≤ 300ms Electrical data Operating voltage UB Residual ripple Open-circuit current Switching output Signal voltage high/low Analogue output Indicators Green LED continuous light flashing off Yellow LED continuous light flashing off 18 … 30VDC (incl. residual ripple) ≤ 15% of UB ≤ 50mA PNP transistor, high-active ≥ (UB -2 V)/≤ 2V voltage 1 … 10V, RL ≥ 2kΩ current 4 … 20mA, RL ≤ 500Ω teach-in on GND Diagrams teach-in on +UB ready fault teaching procedure no voltage object inside teach-in measurement distance teaching procedure object outside teach-in measurement distance Mechanical data Housing Optics cover Weight Connection type metal glass 70g M12 connector, 8-pin, turning Environmental data Ambient temp. (operation/storage) Protective circuit 3) VDE safety class 4) Protection class 5) Laser class Standards applied 1) 2) 3) 4) 5) 6) -20°C … +50°C/-40°C … +70°C 2, 3 II, all-insulated IP 67, IP 69K 6) 2 (acc. to EN 60825-1) IEC 60947-5-2 Remarks Luminosity coefficient 6% … 90%, over the entire temperature range, measurement object ≥ 50x50mm² Same object, identical environmental conditions, measurement object ≥ 50x50mm² 2=polarity reversal protection, 3=short-circuit protection for all outputs Rating voltage 250VAC In stop position of the turning connector (turning connector locked) IP 69K test acc. to DIN 40050 part 9 simulated, high pressure cleaning conditions without the use of additives, acids and bases are not part of the test A B C D E F Area not defined Linearity not defined Measurement range Object present No object detected Measurement distance z Measurement time depends on the reflectivity of the measurement object and on the measurement mode. z Teaching procedure: Position measured object at desired measurement distance. Connect teach input to +UB for ≥ 2s. Reconnect teach input to GND, switching output is programmed. z The voltage output of the analogue version is calibrated before delivery. z Approved purpose: The ODSL 8 laser distance sensors are optical electronic sensors for the optical, contactless measurement of distance to objects. Order guide Designation With M12 connector ODSL 8/V4-45-S12 501 01883 Configuration adaptor UPG 5 500 39627 ODSL 8/V4-45-S12 - 05 0803