Dip Switch Settings Of Trackballs

Transcript

Dip switch settings of trackballs Ver. 1.5 All NSI trackball series and all NSI keyboards with integrated trackball are using trackball modules which are labelled as : (f.i. P38-540420) Pxx-xXxxxx Oxx-xXxxxx Lxx-xXxxxx Xxx-xXxxxx X : denotes the output protocol 0 = Phase quadrature output 4 = “PS/2 only” output 5 = “USB only” output denotes ball diameter in mm 6 = “Combo PS/2 & USB” output A = “RS232 only” output Current range (identified by the label XXX on the IC of the motherboard of the trackball, f.i. LC602A) COMBO protocol types (PS/2 & USB) Partnumber P50-x6xxxx , O50-x6xxxx , L50-x6xxxx and X50-x6xxxx Dip Switch Function OFF ON 1 Orientation 1 See Figure 1 2 Orientation 2 3 VX3 - Virtual 3 Axis Feature disabled Feature enabled 4 Smart feature Feature disabled Feature enabled 5 Tracking mode Ballistic tracking Linear tracking 6 N/A N/A N/A 7 N/A N/A N/A 8 N/A N/A N/A Orientation table Y+ X+ Orientation 2 ON Orientation 2 OFF Orientation 1 ON Orientation 1 OFF X : Dip switch must be in this position VX3™ VX3 is patent protected facility that provides the same 2 modes of functionality as a scroll wheel on a 3-axis mouse. Operation: Press middle button once to latch scroll mode one (e.g. dynamic pan feature); Press middle button again to latch scroll mode two (e.g. 3rd axis zoom feature); Further middle button presses toggles between scroll mode one and scroll mode two; Press either left or right buttons to cancel feature and resume normal X-Y cursor operation Smart Switch A patent protected button latch facility. Press right button for 3 seconds or more to enable; Once enabled, pressing any button for approximately 1 second latches that button on; Press any button momentarily to de-latch; Disabled with a further press of the right button for 3 seconds or more; Tracking Mode Ballistic Tracking: Intuitive tracking algorithm to provide increased cursor resolution when tracking fast whilst retaining the original resolution for tracking accurately at slow speeds. Linear Tracking: No tracking algorithm. 620 counts per ball revolution maintained at all tracking speeds. NSI bvba, Haakstraat 1A, B-3740 Bilzen, Belgium Tel. : ++32 (0) 89 51 90 00 Website : www.nsi-be.com Fax : ++32 (0) 89 51 90 09 E-mail : [email protected] The company reserves the right to alter without prior knowledge the specification or design of any standard product or service. www.nsi-be.com/support.htm 1/2 Dip switch settings of trackballs Ver. 1.5 Former range (identified by the label XXXXX on the IC of the motherboard of the trackball, f.i. 199) COMBO protocol types (PS/2 & USB) Partnumber P50-x6xxxx, P75-x6xxxx, P25-x6xxxx and O50-x6xxxx Dip Switch Function 1 Orientation 1 2 Orientation 2 3 VX3 - Virtual 3 Axis 4 Smart feature Double track.(P75) 5 Y inverted 6 7 8 - OFF Orientation table ON See orientation table Feature enabled Feature enabled Feature enabled Feature disabled X X X Feature disabled Feature disabled Feature disabled Feature enabled - Y+ X+ Orientation 2 ON Orientation 2 OFF Orientation 1 ON Orientation 1 OFF X : Dip switch must be in this position USB protocol types Partnumber P38-x5xxxx, P38-x6xxxx Dip Switch Function OFF ON 1 Orientation 1 See orientation table 2 Orientation 2 3 VX3 - Virtual 3 Axis Feature enabled Feature disabled 4 Smart feature Feature enabled Feature disabled X : Dip switch must be in this position PS/2 protocol types Orientation table Y+ X+ X : Dip switch must be in this position Orientation 2 OFF Orientation 1 ON Orientation 1 OFF Partnumber P38-x4xxxx-5257 Dip Switch Function OFF ON 1 Orientation 1 See orientation table 2 3 VX3 - Virtual 3 Axis Feature enabled Feature disabled See orientation table 4 Orientation 2 Orientation 2 ON Orientation table Y+ X+ Orientation 2 ON Orientation 2 OFF Orientation 1 ON Orientation 1 OFF SERIAL protocol types Partnumber P38-xAxxxx and P50-xAxxxx Dip Switch 1 2 3 4 5 6 7 8 Function OFF ON Protocol mode Microsoft RS232 Mouse systems Orientation 1 See orientation table Orientation 2 Tracking mode Ballistic Lineair Virtual 3 axis* Feature Disabled Feature enabled Baud rate selection* 1200 9600 Smart feature Feature Disabled Feature enabled X Output level Std. RS232 TTL Orientation table Y+ X+ Orientation 2 ON Orientation 2 OFF Orientation 1 ON Orientation 1 OFF X : Dip switch must be in this position * Microsoft mode: VX3 Mouse system: Baud rate selection NSI bvba, Haakstraat 1A, B-3740 Bilzen, Belgium Tel. : ++32 (0) 89 51 90 00 Website : www.nsi-be.com Fax : ++32 (0) 89 51 90 09 E-mail : [email protected] The company reserves the right to alter without prior knowledge the specification or design of any standard product or service. www.nsi-be.com/support.htm 2/2