Transcript
www.beamcommunications.com
Fax: +61 3 9560 9055
Web: www.beamcommunications.com N
S
N
E
80°
×A
8 Anzed Court, Mulgrave
S
60°
BEAM Communications Pty Ltd
I-4 EMEA
100°
Victoria, 3170, AUSTRALIA
90°
40°
120°
W
Info:
[email protected]
0°
Tel: +61 3 8588 4500
A Point SW
140°
40° approx.
E W
160°
I-4 Americas
Support:
[email protected]
PART #: USRMAN006501
180°
Antenna Coverage
90° 80° 70° 60° 50° 40° 30° 20° 10° 0° 10° 20° 30° 40° 50° 60° 70° 80° 90°
inmarsat.com
B Point SE 20° approx.
E W
20°
I-4 Asia-Pacific
40°
0° 20°
×B
0°
90°
W
20°
N
S
N
S
E
40°
60°
Quick Start Guide
E W
80°
0°
90°
30°
120°
W
N
S
N
S
×C
140°
E
160°
180°
Suitable for IsatDocks
Sourced from Inmarsat
100°
30° approx.
Point NE
C
ISD700 Directional/Fixed Antenna (Passive)
E
Directional/Fixed Antenna Installation Guide
Installation Guidelines
Installation Options
Step One:
Option B
To ensure maximum performance of the antenna system and to maximise availability and reliability of service the antenna must;
Place the mounting arm in the mounting swivel and use a hex allen key to tighten the two grub screws.
Fixing the antenna swivel to a 90° surface.
The antenna system is suitable for stationary and fixed applications and is designed to meet Inmarsat System performance requirements when installed according to the instructions in this guide.
•
have a clear line of site to the sky
•
be clear and free of obstructions
•
be clear of metal objects
•
be located away from other transmitting devices
•
be securely affixed in location
•
not be located indoors
Option C
•
be installed in conjunction with a certified cable
Fixing the antenna swivel to a pole.
Installing Antenna Cables
The following figure shows typical Installations:
When installing antenna cables, follow these guidelines:
Step Two:
Step Four:
Place the Antenna on the mounting arm and hold in place. Use the hex bolt and split washer to attach the antenna to the mounting arm and loosely screw them together with the hex allankey provided.
There is a label on the underside of the antenna which indicates “THIS SIDE UP” . Ensure when fitting the antenna in the desired location that this label is facing the sky.
•
Route and restrain cables to prevent them from vibrating or moving under normal conditions, which could result in damage to the antenna or the coaxial cable connections.
•
Wherever the cables contact structures, protect the cables from chafing or abrasion. If a cable needs to be bent, avoid kinking it, and ensure that each bend radius follows the cable supplier limits.
•
Use coaxial sealant, shrink‐wrap tubing, electrical tape, or another suitable product to seal all cable connections appropriately to prevent moisture and corrosion damage from weather exposure.
•
Mount all antennas clear of nearby metal obstructions.
THIS SIDE UP
The antenna must be installed without obstruction of other instruments or structures. The antenna must not be positioned within range of radar equipment or other RF interference.
Directional/Fixed Antenna Kit Contents
Step Three:
Step Five:
You have a number of options for fitting the antenna in position.
One the mounting swivel has been fitted in the correct position the incline angle of the antenna will need to be secured. On the inside of the mounting arm is another hex grub screw. Once the antenna has been put on the correct incline position, tighten the grub screw to hold the antenna position in place.
Option A Fixing the antenna swivel to a flat surface.
1.
Directional/Fixed Antenna
2.
2 x U Bolts
3.
4 x Large Flat Washers
4.
4 x Nuts
5.
Screw with Hex
6.
Split Washer
7.
Mounting Bracket
8.
Mounting Pole
9.
Underside of antenna showing antenna and GPS connections.
THIS SIDE UP
1
2
3 4 5 6 7 8
NOTE: For Satellite & GPS connection instructions please consult your Beam Inmarsat Product manual.
9
