Transcript
84 Avenue Franklin Roosevelt - 69120 VAULX-EN-VELIN Tel : 04 72 14 09 08 - Fax : 04 72 14 02 74 Email :
[email protected]
ACCESS CONTROL (INDEPENDENT WITH CONTACT)
DKF 400 B
This system is composed of a programming unit, readers module (inox) and coded keys. This is a simple, economical and reliable solution for vandalism problems. It replaces all key systems and can be installed in : - Lift - Parking entrance - Doors of buildings (control lock) - Hotel rooms etc..
Technical features : Power supply : Consumption max : Cable lenght between reader module and access control : Number of outputs relay : Number of maximum coded keys : CE compliant :
12V/24V, (AC/DC) type ALS 770 200 mA 100 meters max. (shielded twisted pair) 3 internal + 16 additional (with expansion board 8 relays) 504 keys (NF EN 50081-1 & NF EN 50081-2, NF EN 50082-1 & NF EN 50082-2)
PROGRAMMING UNIT DKF 400 B It can be configured easily through the LCD screen. The different possible functions : - RECORD a key - ERASE a key - TIMING output relays - SELECTION the number of relay outputs : 1, 3 or 19 This programming unit has an internal reader module for programming coded keys READER MODULE This external reader module is made of stainless steel and is waterproof and vandal-resistant. It is connected to the access controler by 2 cables shielded twisted pair (réf : STXP2) over a maximum distance of 100 meters from access control. It is avaible in 3 versions :
READER MODULE TO SCREW TM 400 V
READER MODULE WITH STAINLESS PLATE TM 400 S
KEYS CM 400 The keys consist of a microchip with several billion combinations. Each key has a unique code (patented communication protocol). The key is composed of a molded housing , waterproof, made of plastic. Small, very elegant, it fits easily in keychain. Do not need batteries or maintenance.
1
READER MODULE IN FRONT TM 400 A
In order to program correctly the access control you have imperatively to observe the point 0 to 3 It is possible to exit of the programming menu by selecting “ SORTIE”. Futhermore, the access controller switches automaticaly in the mode “VEILLE” when any buttons is pressed during approximately 20 secondes.
0) GET STARTED
veille
Power the access control with 12 or 24 V (AC or DC) 1) PROGRAMMING OF THE NUMBER OF RELAYS USED menu dkf 400
Press the button : « VAL »
Press 5 times on the decrement key: « DEC » Push the button « VAL »
parametre
You are asked to specify the number of output relays you want to use : To do this, press the button « DEC » and « VAL » - 01 : Only one relay - 03 : 3 relays max - 19 : 19 relays max (with expansion board - ref : MAV 108)
mode parametre nb relais : 03
To save your selection, press the button « VAL » during 3 seconds. Then, press briefly the button « VAL » to return to the menu.
menu dkf 400
2) PROGRAMMING OF THE RELAY TIMING
temporiser
Press 3 times the button « DEC » Press the button « VAL » mode parametre RELAIS 1 : You are asked to specify the output timing relays you want to use. Press the « DEC » or « INC » to select the relay have been choosen. mode temporiser relais 3 : 05 secs Press the button « VAL » to confirm. Using the buttons « DEC » and « INC » to position the desired relay timing. Press the button « VAL » during 3 seconds to save timing Do the same operations with the other relays you want to use.
menu dkf 400
To exit timing mode, press 2 times the button « VAL » . mode memoriser ADRE: 000 V r01 3) RECORDING A KEY Press the button « VAL » . With buttons « INC » and « DEC », move to the address you want to use. Press the button « VAL » during 3 seconds. Then, insert the key into the reader module (internal)
ADRESSE
V:VIDE RELAIS 1
INSERER CLE
This message indicates that the key has been saved at the address : 0 0 0. The message “ P “ indicates that the memory box is full and it will activate relay 1. Press button « VAL » to return to the menu If you have finished the programming of the keys, go to the message « SORTIE » (see page 4) 2
mode temporiser ADRE: 000 P r01
menu dkf 400
4) ERASE A KEY Press 2 times the button « DEC » . Press the button « VAL » .
EFFACER
With buttons « DEC » and « VAL » , move to the address you want to delete. Press the button « VAL » during 3 seconds to confirm the erasing
mode effacer ADRE: 000 p
r
This message indicate that the key saved at address 0 0 0 has been erased. ( « V » indicates memory box is empty) . mode effacer ADRE: 000 V r01
Press button « VAL » to return to the menu 5) DUPLICATE MEMORIES (use with caution) The functions allows you to program many access control units with the same setting and the same keys, you can make the programmation one time, and duplicate it in the others access controlers.
CAUTION YOU USE VERY SENSITIVE COMPONENTS
Firstly, turn off the power of the access controler. Place the empty memory on the MEM2 support on the access controler. Power the access controler. Go to the « DUPLICATE » menu.
DUPLIQUER
Press the button « VAL » during 3 seconds to begin the duplication. It takes about 70 seconds. mode DUPLIQUER ATTENDRE
DURING THE DUPLICATION, DO NOT USE THE ACCESS CONTROL The system automatically returns to the main menu at the end of the duplication. Now, power off the access control. Remove the memory MEM2. Now, it contains the same information as the memory MEM1.
YOU HAVE FINISHED PROGRAMMING ?
menu DKF 400
MENU DFK 400
SORTIE
YES : Press 6 times on the button « DEC »
Press the button « VAL » Access control switches into “SLEEP” mode. It is ready to use. VEILLE
NO : I would like to change the programmation.
With buttons « INC » and « DEC », go on the function you wish to modify.
3
CONNECTION DIAGRAM OF THE ACCESS CONTROLER
DKF 400 B
4
ADDRESS : ................................................................................................................................................. TECHNICIAN : ........................................................................................................................................... NUMBER OF RELAYS USED : ............................................ TIMING RELAY 1 :
............................................
TIMING RELAY 2 :
............................................
TIMING RELAY 3 :
............................................
NUMBER OF KEYS USED :
............................................
SELECTION TABLE NUMBER OF RELAY (1) KEY : 0 at 503
ACTIVATE RELAY 1
NUMBER OF RELAY (3) KEY : 0 at 83 KEY : 252 at 335
RELAY 1 RELAY 1
KEY : 84 at 167 KEY : 336 at 419
RELAY 2 RELAY 2
KEY : 168 at 251 KEY : 420 at 503
NUMBER OF RELAY (19)
KEY : 0 at 20 KEY : 21 at 41 KEY : 42 at 62 KEY : 63 at 83 KEY : 84 at 104 KEY : 105 at 125 KEY : 126 at 147 KEY : 148 at 167 KEY : 168 at 188 KEY : 189 at 209 KEY : 210 at 230 KEY : 231 at 251 KEY : 252 at 272 KEY : 273 at 293 KEY : 294 at 314 KEY : 315 at 335 KEY : 336 at 356 KEY : 357 at 377 KEY : 378 at 503
RELAY 1 RELAY 2 RELAY 3
INTERNAL RELAYS OF THE ACCESS CONTOLER
RELAY RELAY RELAY RELAY RELAY RELAY RELAY RELAY
4 5 6 7 8 9 10 11
RELAY 1 OF THE EXPENSION BOARD
RELAY RELAY RELAY RELAY RELAY RELAY RELAY RELAY
12 13 14 15 16 17 18 19
RELAY 2 OF THE EXPENSION BOARD
5
RELAY 3 RELAY 3
TECHNICIAN : .................................................................................................................................................. INSTALLATEUR : ………………………………………………………………………… ADDRESS : ........................................................................................................................................................ RESIDENCE : ……………………………………………………………………………… NUMBER DE OF CLES KEYS :: ........................................................................................................................................... NOMBRE ……………………………………………………………………...
NUMERO CLE KEY NUMBER
KEY ADDRESS AFFECTED ADRESSE DE LA CLE BY ACCESS CONTROLER DANS LA CENTRALE
6
AFFECTE A Mr ou Mme :
AFFECTED TO M. OR Ms.
