Transcript
Page
1
User Guide - Campen
With the "Mode Switch", you can select between Video and Audio recording. In the Video mode, the status light will be yellow illuminated (standby). In the Photograph mode, the status light twinkles in yellow (standby).
Manual 2 Operating - Video Recording 3 Operating - Motion Detect Recording 4 Operating - Photograph 5 Operating - Connection to PC 6 7 Operating - Time setting Operating - Battery charging & Reset I 9 Fact Sheet of Campen lnstruction
Safety Instructions
Mode Switch
11
Specification
12
Photograph
Battery charging LED in RED Warning: Do not switch mode while recording.
Page2
OPERATING
Page 5
5. How to take photo Please be sure the Mode Switch is on Photograph mode. Press the On/Off button about 2 seconds and the status light will be in yellow blinking (standby). Press the ON/OFF button again for taking photo and the status light will blink a second in blue. After completion the photograph, the status light will turn back to yellow blinking (standby).
simple operation, elegant design, small size, it is easy to carry. lt is an essential utility in business, education, security, media, justice, health care, living and other fields.
Please Notice: A. lfthe device is not used for a short period about 30 seconds, it will turn off automatically in order to save power. B. Before the battery runs out of power, the device will automatically save the current file and turn off. C. The system will create a new file after stopping recording. D. lt takes a few seconds to save the file, do not operate the device until the light turns yellow. lt can lead to the corrupt files if you do. E. Make sure there is adequate light in the surrounding and the camera is not blocked by other items. Keep the camera upright and stable. And the object should be more than 50cm from the camera.
Pen assembly: 1. Status Light (Yellow and Blue) 2. Reset 3. Mode Switch (Video/Audio)
4. USB On/Off Button Camera Microphone (under clip) Battery Charging Light (Red)
OPERATING:
side switch
Video mode
This ball-pointer pen is a high-definition video recorder with built-in memory, with
5. 6. 7. 8.
-
Please use pen lead to push the slide switch to choice the function vou need.
10
I
Safety Instructions ll
INTRODUCTION:
Page 4
OPERATING: 4. Switching Modes (Video/Photograph)
Pase
3
1. Power On Please be sure the Mode Switch is in "Video mode". In order to turn on the camera, press the ON/OFF button for 2 seconds. Wait until the status light glowing constantly yellow The camera is now ready to use (standby).
2. Start Video Recording Press the ON/OFF button again. The status light blinks in blue and it is video recording.
3. Stop Recording Press the ON/OFF bufton again to stop recording. Now the device will save the footage. The status light will turn yellow illuminated again (standby). Press and hold the ON/OFF button about 5 seconds to power off.
Please notice: Once activated, the device will need a short period oftime to boot up. Do not press the ON/OFF button during that procedure. The time to boot up the system depends on the storage size of the device. The more storage the device has, the more time the boot up procedure will take. In order to ensure good sound effect of recording, do not block the microphone hole.
OPERATING:
Page 6
6. Turn off the Device It will turn off automatically within 30 seconds in standby mode without any operating. The system will automatically save the file while turning off. Or push the ON/OFF button and hold it about 5 seconds to switch it off.
You can connect the device with your computer, no matter if it is on or off. Simply screw up the pen and stick the USB of the pen into your computer. You can access the USB volume directory: USB volumeVlDEO\ lmages are saved under the USB volume directory: USB volume\IMAGES\
8. Write rwist tne pen's head and the ball-pen
iiil#
into the
J'y:l
'iT,]'.lf; e. Replace the Pen i"i*i'.",:""Hj:lJ
appears. I
opposite
T
refill.
:;iffi,il,",T}
I
Il
i I ili
ru;u:
H qU
OPERATING:
PaseT Safetylnstructions:
In order to disconneci the device, please click "SAFELY REMOVE HARDWARE" on the right bottom corner of the task bar. Then click "USB mass storage device". Unplug the USB. The disconnection completes.
According to the computer or system configuration, there will be slightly different time of identification. Please be patient and don't press the ON/OFF bufton during this period. It may cause a bad impact of computer hardware. lf the computer does not identify the device, please disconnect and reconnect the device. lf the computer is unable to identify the hardware yet, make sure your operating system, driver and USB cable are all in working condition. Please make sure to disconnect the device in accordance with the normal process to avoid a possible damage for computer and recorder.
laws. This product should not be used for any illegal purposes. The user is fully responsible for its using purpose.
Battery: lf do not use this recording function after long time, please charged it once per month at least to keep the good condition of battery. File Securitv: This product is not a professional storage device. It does not guarantee the integrity and security saved files. Please back up your important documenis on the computer or Operating humiditv: 20%-B0o/". This product does not have the waterproof function. So it cannot work under the humid environment.
Plug the device to the computer and double click the "Date Time.exe", and then click setting. Remove it from your computer and Dress the reset button to complete the time setting.
Shooting briqhtness: Do not expose the camera directly to strong light, such as the sun light, to avoid damage to optical devices.
Pase
8
11. Battery Charging Connect to pen with the computer USB port or the charger. During the charging, the red light illuminates closing to the USB connector. When the battery is fully recharged, the red light will be off.
Please Notice: The recorder has a built-in high-capacity lithium polymer battery. lt can be used and charged at any tlme. But for the first five charging times, please charge baftery to the maximum, after the battery runs out. This will activate the batteries maximum capacity and maintain in the standard working time.
12. Reset lf the recorder stops responding, please use the suitable nonmetallic tool to push the RESET button.
Please Notice: lf the device stops working due to improper operation or other unknown reason, please reset it slightly.
Fact Sheet of CampCn:
Application: Please strictly abide relevant regulations and
other storage device timely
't0. Time settinq
OPERATING:
Page'10
Page
e
Please read the instructions carefullV.
