Transcript
dogPACER QUICK START GUIDE
For latest info, tips, and photos go online to: www.dogpacer.com
Congratulations! You have taken the first step in your dog’s health, happiness and a better life! We encourage you to go online to www.dogPACER.com to see other dog owners running their dogs and to join our Facebook community for special offers and information.
Overhead Bar Running belt Running belt Running belt Running belt Running belt Running belt Running belt Running belt
R Safety Key u Computer n Safety Key n i Computer Safety Key n g Safety Key Computer b e Transport wheels l Computer t Transport wheels O Side rail Side p anel Transport wheels v e Transport wheels r Side rail Side p anel h Motor C Transport wheels eover r a Side rail Legs Side p anel Transport wheels d Motor C over Power Switch r rail Transport wheels B Side Side p anel Legs a Power S witch Motor C Transport wheels r over r Side rail Power S witch Legs Side p anel 1.0 Initial Assembly Motor CRover Power Switch r rail u or carpeted surface. Side Protect your floor by placing the dogPACER on cardboard, a mattress Legs Side p anel n n plenty of room to work. Take the dogPACER out of its box. Lay in an open area so you have i Side rail Legs Side p anel Open the legs and lock them into place using the Centre Pins (Bolt Ø6). n g NOTE: You only need to use 2 of the Centre Pins – the additional 2 are used for the incline Side rail b Legs Side panel feature. e l
2.0 Attach the Overhead Bar Put the overhead bar into place using the 4 M6*15 screws. NOTE：Please insert all the screws initially and tighten one by one using the 5mm Hex Key. Do not over tighten.
3.0 Connect the computer 1.
Put the computer with the cable through the leg and connect the computer to the leg using ST4.2*12 screws (see diagram).
2.
Connect the computer with the cable connector.
3.
Connect the computer to the treadmill with two screws (ST4.2*12)
Insert the tapping Screw ST4.2*12
Connect the cable
Hex bolt M6*15 Motor cover Plain washer Φ6 Motor cover
4.0 Attach side panels 1. When the dogPACER is in position, lay the side panel down on the belt. Insert the side panel to the rubber clips (A, B & C) on the P.V.C. side rails. 2. Put the upper part of the side panel under the fixed clip on upper bar (see diagram below).
5.0 Starting your dogPACER Connect the power cable to the machine and an outlet. Make sure the Safety Key is in its place. Turn the switch to ON mode (amber light).
6.0 Computer console: Speed + Speed + Speed + -‐ Speed Speed + Speed -‐ Speed -‐ Mode Speed -‐ mode mode
Start / Stop
Safety key Safety key Safety key Safety key
7.0 Belt tracking adjustment (ONLY IF NEEDED. DO NOT ADJUST OUT OF THE BOX): 1. Start the treadmill by pushing the start/stop button. 2. At minimum speed, go to the back of the dogPACER and see if the running belt stays in the middle. If it shifts to the right or left do the following:
If the belt shifts to the left: If the belt shifts to the right: 1. The left side doesn’t have enough 1. The right side tension, and right doesn’t have enough side is fine -‐ tighten tension, and left side is the left knob. fine -‐ tighten the right knob. 2. The tension of the left side is fine, the 2. The tension of the tension of right side right side is fine; the is too tight -‐ loosen tension of left side is the right knob. too tight -‐loosen the left knob. The belt shifts to the The belt shifts to the right: left: 8.0 After set up – Quick Start Operation: 1. The left side doesn’t 1. The right side have enough tension, 1. Press and release the START/STOP to begin belt movement, at 0.5 MPH, thenhadjust to the doesn’t ave enough and right side is good, tension, and left side please tighten the left desired speed using the ‘+’ or ‘-’. is good, please knob. 2. The tension of hold the the ‘-’ key to desired speed.tighten the right 2. To slow the treadmill down, press and knob. left side is good, the 2. The tension of the tension of rSTART/STOP ight side is 3. In a state of running, single press , the walking belt will gradually slow down right side is good, the too tight, please loosen tension of left side is to a stop. the right knob. too tight, please loosen the left knob. Calorie Display Displays the cumulative calories burned at any given time during your pet’s workout.
Note: This is only a rough guide used for comparison of different exercise sessions, which cannot be used for medical purposes.
9.0 Pre-set programs Each pre-set program has a maximum time of 30-minutes per workout. It will always start at 10 min and can be adjusted to suit your pet’s level. Choose from P1, P2, or P3 to give your pet the desired exercise. Each program has various speed changes throughout the program (see list of programs in User Manual). Power on the machine, press ‘MODE’ to choose desired program, then press and release ‘START/STOP’ to begin the program with default values.
For any further information, trouble shooting or help please see dogPACER User Manual or go online to: www.dogpacer.com
Warranty:
YOU HAVE 60 DAY TO REGISTER THIS PRODUCT, VISIT: www.dogpacer.com
Technical support
dogPACER provides technical support. Please write an email to –
[email protected] For further information and help please see USER’S MANUAL or for FAQ’s and instructional videos go to: www.dogpacer.com
YOUR DOG’S OTHER BEST FRIEND
