Transcript
97_QS.book Page 1 Thursday, September 9, 2010 9:57 AM
Dolphin™ 9700 with Windows Mobile® 6.5
Quick Start Guide
97_QS.book Page 2 Thursday, September 9, 2010 9:57 AM
Disclaimer Honeywell International Inc. (“HII”) reserves the right to make changes in specifications and other information contained in this document without prior notice, and the reader should in all cases consult Honeywell to determine whether any such changes have been made. The information in this publication does not represent a commitment on the part of HII. HII shall not be liable for technical or editorial errors or omissions contained herein; nor for incidental or consequential damages resulting from the furnishing, performance, or use of this material. This document contains proprietary information that is protected by copyright. All rights are reserved. No part of this document may be photocopied, reproduced, or translated into another language without the prior written consent of HII. Web Address: www.honeywellaidc.com
Trademarks Dolphin and HomeBase are trademarks or registered trademarks of Hand Held Products, Inc. or Honeywell International Inc. Microsoft, Windows, Windows Mobile, ActiveSync, and the Windows logo are trademarks or registered trademarks of Microsoft Corporation. Other product names or marks mentioned in this document may be trademarks or registered trademarks of other companies and are the property of their respective owners. ©2010 Honeywell International Inc. All rights reserved.
97_QS.book Page 1 Thursday, September 9, 2010 9:57 AM
Out of the Box Verify that the carton contains the following items: • • •
Dolphin 9700 mobile computer (the terminal) Main battery pack (7.4V Li-ion) Quick Start Guide
Note: If you ordered accessories for your terminals, verify that they are also included with the order.
Be sure to keep the original packaging in the event that the Dolphin terminal should need to be returned for service.
Front Panel Power Key
Front Speaker
Touch Panel Display Scan Key Microphone
Indicator LED
Volume Button Right Button I/O Connector
Navigation Keys
1
97_QS.book Page 2 Thursday, September 9, 2010 9:57 AM
Back Panel Battery Door
Hand Strap
Stylus Slot
IRDA Port
Left Button Stylus Fastener
Image/Scan Engine Window Memory Card Socket
SIM Card Socket Battery Well
Flashlight/ Camera Flash Color Camera
Rear Speaker
2
97_QS.book Page 3 Thursday, September 9, 2010 9:57 AM
Available Keyboards 31-Key Numeric Keyboard SCAN VOL PG
TAB
ENT
®
ESC
1
F1 @?!
2
F2 ABC
3
4
F4 GHI
5
F5 JKL
F6 6 MNO
F7 PQRS
8
F8 TUV
F9 9 WXYZ
0
F10 &
7
*.
F3 DEF
ALT SP
#
,
45-Key QWERTY Keyboard SCAN VOL PG
TAB
ENT
®
! F1
Q
@
A *
Z
1
F2
W
4
2 F3
3 F4
E
$ F5
R
5
6
Y
;
- F8
) F7
( F6
T
I
U
:
“
+ F9
O
?
S
D
F
G
H
J
K
7
8
9
#
/
\
,
X
C 0
.
V
B
SPACE
N
M
= F10
P
&
L
-
ESC
3
97_QS.book Page 4 Thursday, September 9, 2010 9:57 AM
Install the Main Battery Pack The 9700 is shipped with the battery packaged separate from the unit. Follow the steps below to install the main battery. 1. Release the hand strap near the base of the terminal. 2. Remove the battery door by releasing the door latch and pulling up with a hinging motion. 3. Insert the battery into the battery well.
4. Replace the battery door. Apply pressure to engage the door latch. Note: The battery door must be installed prior to powering the unit.
5. Reattach the hand strap. 6. Connect the terminal to one of the 9700 series charging peripherals to charge the main battery pack.
! 4
We recommend use of Honeywell Li-Ion battery packs. Use of any non-Honeywell battery may result in damage not covered by the warranty.
97_QS.book Page 5 Thursday, September 9, 2010 9:57 AM
Charging the Dolphin The initial charging time for the main battery pack is 6 hours, and 8 hours for the internal backup battery. Connect the terminal to one of the 9700 series charging peripherals to charge the main battery.
HomeBase
AUX Battery Well Dock LED
COMM LED AUX Battery LED
5
97_QS.book Page 6 Thursday, September 9, 2010 9:57 AM
HomeBase Back Panel USB Port Serial Port DC Power Jack
HomeBase LED Indicators Green
The terminal is properly seated in the base.
Orange The auxiliary battery is charging. Green
The auxiliary battery has completed charging and is ready for use.
Serial Port Communication Red
Serial data is being sent from the host device to the base.
Green
Serial data is being sent from the base to the host device.
Orange Serial data is being sent in both directions at the same time. USB Port Communication Green
6
A USB connection is established with the host workstation.
97_QS.book Page 7 Thursday, September 9, 2010 9:57 AM
Charging/Communication Cable Power Adapter Cable Power Cord
Host Device COMM Cable USB Connector Or
RS232 Connector
LED Indicators The light emitting diode (LED) located at the top of the LCD display flashes and illuminates during resets, scanning/imaging and taking a picture. This LED can be programmed by various software applications. 7
97_QS.book Page 8 Thursday, September 9, 2010 9:57 AM
Battery Status Indicator The Dolphin’s battery status is indicated at the top of the touch screen in the Navigation Bar. The battery is charging. The terminal is using an external power source. The battery has a full charge. The battery has a high charge. The battery has a medium charge. The battery has a low charge. The battery has a very low charge. Charge the battery.
ActiveSync Communication To synchronize the host workstation and the Dolphin terminal, ActiveSync 4.5 or higher must be installed and configured for the appropriate communication type on both devices. Dolphin terminals ship with ActiveSync already installed. Therefore, you just need to connect the Dolphin terminal to the host workstation (via Dolphin peripheral) to initiate communication. Note: You can download the most current version of ActiveSync from www.microsoft.com. We recommend use of Honeywell peripherals, power cables, and power adapters. Use of any non-Honeywell peripherals, cables, or power adapters may cause damage not covered by the warranty.
!
8
97_QS.book Page 9 Thursday, September 9, 2010 9:57 AM
Installing a Memory Card 1. Press the Power key to put the terminal in Suspend Mode. 2. Release the hand strap near the base of the terminal. 3. Remove the battery door and the battery. 4. Remove the protective cover over the memory socket. 5. Unlock the access door to the memory socket by sliding the door away from the serial number label located in the battery well. 6. Lift the door up to expose the socket. 7. Insert the microSD or microSDHC card into the socket.
Step 4
Step 5
Step 6
Step 7
Note: Make sure the interface on the memory card is connected to the interface in the socket; align the notch on the card with the notch of the socket.
8. Close and lock the access door by sliding the door toward the serial number label. 9. Replace the protective cover over the memory socket. 10. Install the battery and the battery door.
8 Step 4
Step 49
9
97_QS.book Page 10 Thursday, September 9, 2010 9:57 AM
11. Press and hold the RED approximately 5 seconds.
+ TAB
TAB ®
keys for
12. The decode and scan LEDs flash for approximately three seconds as the terminal resets. 13. When the reset is complete, the Today screen displays. Note: Honeywell recommends formatting all SD cards before initial use.
10
97_QS.book Page 11 Thursday, September 9, 2010 9:57 AM
Installing a SIM Card 1. Press the Power key to put the terminal in Suspend Mode.
Step 4
2. Release the hand strap near the base of the terminal. 3. Remove the battery door and the battery. 4. Remove the protective cover over the SIM socket. 5. Unlock the access door to the SIM socket by sliding the door away from the serial number label located in the battery well.
Step 5
Step 6
6. Lift the door up to expose the socket. 7. Insert the SIM card into the socket. Note: Make sure the interface on the card is connected to the SIM Card interface in the socket; align the beveled corner of the card with the beveled corner of the socket.
8. Close and lock the access door by sliding the door toward the serial number label.
Step 7
Step 8
Step 9
9. Replace the protective cover over the SIM socket. 10. Install the battery and the battery door.
11
97_QS.book Page 12 Thursday, September 9, 2010 9:57 AM
Using the Scan Image Engine 1. Tap Start > Demos
> Scan Demo
2. Point the Dolphin’s terminal at the bar code.
3. Project the aiming beam or pattern by pressing and holding the SCAN key side buttons.
SCAN
or one of the terminal’s
4. The red LED lights. 5. Center the aiming beam over the bar code; see Aiming Options on page 13. 6. When the bar code is successfully decoded, the LED changes to green and the terminal beeps. 7. The bar code information is entered into the application in use.
12
97_QS.book Page 13 Thursday, September 9, 2010 9:57 AM
Aiming Options 5300 Red High-Vis Aiming Pattern
5100 Green Aiming Beam Linear Bar Code
2D Matrix Symbol
13
97_QS.book Page 14 Thursday, September 9, 2010 9:57 AM
Using the Color Camera 1. Tap Start > Demos > Camera Demo 2. Adjust the camera settings using the menu at the top of the display screen. Color Brightness
Pixels
Zoom
3. Point the terminal's camera lens at the object you want to capture. The camera lens is located on the back panel of the terminal. 4. Center the object in the touch screen display. ENT
5. Press the ENT key . The terminal’s red LED illuminates during picture capture. Note: Tap the green arrow to review or edit your pictures. Tap the green box to exit the picture review/edit screen.
14
Flash Camera Lens
Camera Flash
97_QS.book Page 15 Thursday, September 9, 2010 9:57 AM
Soft Reset (Warm Boot) A soft reset re-boots the device without losing RAM data. 1. Press and hold the RED approximately 5 seconds.
+ TAB
TAB ®
keys for
2. The decode and scan LEDs flash for approximately three seconds as the terminal resets. 3. When the reset is complete, the Today screen displays.
Hard Reset (Cold Boot) A hard reset resets the operating system, restores the terminal back to factory defaults, and resets the terminal after a bootloader, keyboard, and kernel upgrade.
!
A hard reset erases all of the data stored in RAM memory and all RAM installed applications!
1. Press and hold the RED approximately 5 seconds.
+ ENT
ENT
keys for
2. The decode and scan LEDs light for approximately 3 seconds. 3. The terminal re-initializes.
15
97_QS.book Page 16 Thursday, September 9, 2010 9:57 AM
Technical Assistance Contact information for technical support, product service, and repair can be found at www.honeywellaidc.com.
User Documentation Refer to www.honeywellaidc.com for detailed user documentation or for localized versions of this Quick Start.
Limited Warranty Refer to www.honeywellaidc.com/warranty_information for your product’s warranty information.
16
97_QS.book Page 17 Thursday, September 9, 2010 9:57 AM
97_QS.book Page 1 Thursday, September 9, 2010 9:57 AM
Honeywell Scanning & Mobility 9680 Old Bailes Road Fort Mill, SC 29707 www.honeywellaidc.com
97-QS Rev C 9/10
