Dolphin Behind Mirror Soap Dispenser

Transcript

140 20 100 50 30 320 260 POWER SUPPLY 100 45 120 140 BC634 DOLPHIN BEHIND MIRROR SOAP DISPENSER › Easy to fit behind mirror infrared soap dispenser for contemporary washroom design with an uncluttered appearance HEIGHT 320 MM WIDTH 140 MM PROJECTION 120 MM › Designed to be fitted behind hinged mirror or panel (access required to replenish soap supply) MINIMUM HEIGHT ABOVE SURFACE BELOW › Touch-free – thus eliminating cross-contamination ALLOW OVERALL HEIGHT FROM BOTTOM OF 300 › Capacity 1,000 ml BASEPLATE 400 MM MM › 1.8ml of soap per dispensing cycle – adjustable on-site with Dolphin key ring › Helps prevent vandalism – vandal resistant › Powered by 9v transformer. Draws maximum current of 0.5A at sensor activation › Chrome plated nozzle designed to protrude slightly below bottom edge of mirror making it quick and easy to identify and use › 1,000ml refillable plastic container (no need to purchase unique soap reservoirs) › 2 year guarantee › The peristaltic pump allows the use of different soap viscosities, including antibacterial gels › Easy to use refill button (either on the dispenser pump, or by means of the Remote Control) - use window in baseplate for checking soap levels › Backplate made from stainless steel › Power connections: soap dispenser: female / power source: male TECHNIC AL HELPLINE 01424 202224 DOLPHINSOLUTIONS.CO.UK 140 20 100 50 30 320 260 POWER SUPPLY 100 45 120 140 BC634 DOLPHIN BEHIND MIRROR SOAP DISPENSER › Easy to fit behind mirror infrared soap dispenser for contemporary washroom design with an uncluttered appearance HEIGHT 320 MM WIDTH 140 MM PROJECTION 120 MM › Designed to be fitted behind hinged mirror or panel (access required to replenish soap supply) MINIMUM HEIGHT ABOVE SURFACE BELOW › Touch-free – thus eliminating cross-contamination ALLOW OVERALL HEIGHT FROM BOTTOM OF 300 › Capacity 1,000 ml BASEPLATE 400 MM MM › 1.8ml of soap per dispensing cycle – adjustable on-site with Dolphin key ring › Helps prevent vandalism – vandal resistant › Powered by 9v transformer. Draws maximum current of 0.5A at sensor activation › Chrome plated nozzle designed to protrude slightly below bottom edge of mirror making it quick and easy to identify and use › 1,000ml refillable plastic container (no need to purchase unique soap reservoirs) › 2 year guarantee › The peristaltic pump allows the use of different soap viscosities, including antibacterial gels › Easy to use refill button (either on the dispenser pump, or by means of the Remote Control) - use window in baseplate for checking soap levels › Backplate made from stainless steel › Power connections: soap dispenser: female / power source: male TECHNIC AL HELPLINE 01424 202224 DOLPHINSOLUTIONS.CO.UK INSTALLATION AND MAINTENANCE GUIDE BC634 B E H I N D F R E E TO U C H F R E E SOAP DISPENSER Saving soap, saving power, promoting hygiene Important: Read carefully before installing product INDEX 3 Technical Data 4 Pre-Installation Information 5 Pack Contents 6-8 Installation 9 Filling The Soap Tank 10 Settings Adjustment with a Remote Control 11 Batteries Replacement 12 Maintenance Care And Cleaning Of Chrome And Special Finishes 13 Spare Parts List 14 Warranty 15 Trouble Shooting 2 | Dolphin Blue | BC 634 TECHNICAL DATA Behind mirror Soap Dispenser BC 634B Behind mirror Soap Dispenser BC 634E Capacity: 1 Litre \ 33.8 oz. Power Supply: IP 67 Battery Box for 6xD Alkaline batteries \ Transformer Soap viscosity: 100 – 3800 cPs Standard discharge: 0.8cc, Adjustable Sensor range: 30-100 mm +/- 10 mm (Adjustable by remote control). BC 634 | Dolphin Blue | 3 PRE INSTALLATION INFORMATION Check contents Separate all parts from the packaging and check each part with the “Pack contents” section. Make sure all parts are accounted for before discarding any packaging material. If any parts are missing, do not attempt to install your touch free soap dispenser until you obtain the missing parts. Warnings 1) To avoid reflection problems keep a distance of more than 300 mm. between the sink and the spout. 2) This tap model, with an infrared sensor pointing down, is not intended to be used together with a sink of a reflective material such as stainless steel. 3) If a sink strainer is straight below the tap sensor, use a strainer with a non reflective finish (do not use a chrome plated one). 4)To prevent reflection problems, it is recommended to keep a minimum distance of 1.50 meters between the soap dispenser and any other objects. Important: Pay attention that the dimensions of the mirror compartment fits the dimensions of the Behind Mirror Soap Dispenser plate. 4 | Dolphin Blue | BC 634 PACK CONTENTS Familiarise yourself with the part names and confirm that the parts are included. 4 screws up to 5mm (not supplied) IP 67 Battery box for 6 x D alkaline batteries Transformer Product assembly containing: Pump with bottle support,plate with spout and soap tank BC 634 | Dolphin Blue | 5 INSTALLATION Step 1 : Preparation for installation Cut a hole in the bottom of the mirror compartment for the soap dispenser sensor and spout both. The recommended hole size should be 30x50 mm. Step 2 : Installing the soap dispenser 1. Remove the protective sticker covering the sensor. 2. Place the soap dispenser assembly inside the mirror compartment with the spout sticking out of the hole. 6 | Dolphin Blue | BC 634 INSTALLATION 3. Secure the plate to the wall with 4 screws (not supplied). Step 3 : Connecting the power source Make sure that the 4 contacts O-ring visible – not connected properly connector is connected properly so that the white o-ring is not visible. Pay attention: If the 4 contacts connectors will not Connected properly so that only the groves are visible be connected properly, the motor will work continuously. BC 634 | Dolphin Blue | 7 INSTALLATION For battery versions: Install the battery box at the wall in the mirror compartment and connect the battery connector. For transformer versions: Plug the transformer into the electricity socket and make sure the transformer connector is connected. Wait about 10 seconds before you put your hands within the sensor range. 8 | Dolphin Blue | BC 634 FILLING THE SOAP TANK 1. Unscrew the soap tank from the pump assembly. 2. Fill in the liquid soap up to the top line. 3. Insert the bottle with the tube inside the bottle support. 4. Screw the soap tank back to the pump assembly. Make sure the tank is secured firmly in place. 5. Press the refill button located at the back of the pump assembly until soap starts coming out of the soap dispenser spout. This operation can also be done using the soap dispenser remote control Refill function. Note: Once the soap in the soap tank has reached the bottom line the soap tank should be refilled. To refill the soap tank please refer to steps 1-5. BC 634 | Dolphin Blue | 9 SETTINGS ADJUSTMENT WITH A REMOTE CONTROL If desired, use the remote control to adjust the soap dispenser settings. Hold the remote control straight in front of the sensor in a distance of about 4-6” (1015cm). Attention: Holding the soap dispenser remote control out of the recommended range (too close or too far)may interfere with the remote’s activation. Choose the function you want to adjust by pressing on the function button as following: 1 Soap Quantity The 1-4 drop keys allow the user to choose the desired soap quantity. Indication: continues blink of the red light in the sensor eye. * The exact soap dosage depends on the soap viscosity. 1 0.2 to 0.4 2 0.7 to 0.9 3 1.2 to 1.6 4 2.1 to 2.3 2. ADJ This function allows coming back to soap quantity factory settings. Press the ADJ button. Indication: 2 blinks of the red light in the sensor eye. 3 Temporary Off Function This function is ideal to perform any kind of activity in front of the sensor without operating the system (for example, cleaning). The soap dispenser will remain shut for 1 minute when this button is pressed once. To cancel this function and to return to normal operation press the On/Off button again or wait 1 minute. Indication: OFF – 2 fast blinks, ON – 4 fast blinks 4 Refill The Soap Tank Once the soap tank has been refiled, press the FILL button. The pump would work for one minute in order for the soap to start coming out of the soap dispenser spout. To stop this activity press the FILL button again. 10 | Dolphin Blue | BC 634 BATTERY REPLACEMENT Battery models only When the battery weakens, the red indicator light will blink at a constant rate when the user’s hands are within the sensor range. The battery must be replaced within two weeks. To replace the battery in battery models: 1. Carefully open the battery box place within the mirror compartment, using 2.5 mm Allen key 2. Remove the old batteries 3. Replace the used batteries with new D batteries NOTE: Do not mix used batteries with new ones. Important: Spent batteries should not be disposed of with normal household waste. Contact your local authority for information on waste disposal and recycling. BC 634 | Dolphin Blue | 11 MAINTENANCE Care and cleaning of chrome and special finishes DO NOT use steel wool or cleansing agents containing alcohol, acid, abrasives, or the like. Use of any prohibited cleaning or maintenance products or substances could damage the surface of the soap dispenser. For surface cleaning use ONLY soap and water, then wipe dry with a clean cloth or towel. When cleaning bathroom tiles, the soap dispenser should be protected from any splattering of harsh cleansers. 12 | Dolphin Blue | BC 634 SPARE PARTS LIST Part Name Part Code Sensor kit BC 07220230 Soap tank 1 L BC 07100020 Transformer BC 06522042 Soap dispenser Pump assembly BC 07222001 Remote control BC 07100008 IP67 transformer box BC 06530021 IP 67 Battery Box for 6xd alkaline batteries BC 06530041 Bottle support 1 L BC 07120175 Soap dispenser spout assembly BC 07271023 BC 634 | Dolphin Blue | 13 LIMITED WARRANTY Filter cleaning instructions The tap is provided with one stainless steel filter preventing foreign particles to enter the lines. If the water flow has decreased, this may be because the filter is clogged. The filter can be cleaned as follows: 1. Shut-off the water shut off valve. 2. Disconnect the water supply inlet from the adapter at the solenoid valve housing. 3. Remove the filter from the adapter and wash it under running water. 4. Reassemble the parts. 5. Reconnect the solenoid valve housing and restore the incoming water supply. 6. Make sure that there is no water leakage. Care and cleaning of chrome and special finishes DO NOT use steel wool or cleansing agents containing alcohol, acid, abrasives, or the like. Use of any prohibited cleaning or maintenance products or substances could damage the surface of the tap. For surface cleaning of tap us ONLY soap and water, then wipe dry with clean cloth or towel. When cleaning bathroom tile, the taps should be protected from any splattering of harsh cleansers. 14 | Dolphin Blue | BC 634 TROUBLE SHOOTING PROBLEM INDICATOR Sensor flashes continuously when user’s hands are within the sensor’s range No water comes out of the tap Red light in the sensor does not flash once when user’s hands are within the sensor’s range CAUSE Low batteries Replace batteries Range is too short Increase the range with remote Range is too long ie tap has gone into security mode Decrease the range with remote Batteries are completely used up Replace batteries Sensor is picking up reflections ie tap has gone into security mode Decrease the range or eliminate cause of reflection Connectors between the electronic unit and the solonoid are disconnected Red light in the sensor flashes once when user’s hands are within the sensor’s range Sensor flashes once when user’s hands are within the sensor’s range Water flow from spout does not stop Water flow diminished Red light in the sensor does not flash when user’s hands are within the sensor’s range SOLUTION Debris or scale in solonoid Connect the electronic unit connectors to the solonoid Unscrew solonoid, pull out the plunger and the spring from the solonoide and clean them. Use scale remover material if needed. When replacing the plunger,please make sure that the spring is in vertical position The central orifice in the diaphragm is plugged or the diaphragm is torn Unscrew solonoid and clean the orifice and/or replace diaphragm The water supply pressure is higher than 8 bars Reduce the water supply pressure Debris or scale in diaphragm Unscrew solonoid, remove diaphragm and clean or replace. Use scale remover if needed. Sensor is dirty or covered Clean or eliminate cause of interference Sensor is picking up reflections from the washbasin or another object Decrease the range or eliminate case of reflection Filter or aerator is clogged Remove, clean and reinstall BC 634 | Dolphin Blue | 15 Tel: +44 (0)1424 20 22 24 Fax: +44 (0)1424 205 200 [email protected] www.dolphinsolutions.co.uk Southpoint, Compass Park, Bodiam, Robertsbridge, TN32 5BS Dolphin Solutions Ltd egnaR letoH elbamusnoC s tcudorP seilimaF smeti detaleR noitallatsnI ediuG 178 Dolphin Dispensers page 180 DBL 400 Technical helpline page 11 WP 106 ybaB gnignahC • Operating pressure 0.5–8.0 bar (7–116 PSI) • Maximum water temperature 70ºC • 2 year manufacturer ’s warranty • WRAS Approved Product sliaR barG 01424 202224 combat Legionella – please specify at time of orering • Mandatory Hygiene Flush feature can be specified to control (DB51 – see page 188) • Tap settings can be adjusted manually or by using remote • Neopearl Aerator please specify at time of ordering) • Flow rate – 6 litres/minute (down to 1.89 litres/minute page 183 – premixed applications. For 2 inlet hot and cold feed see TMV3 thermostatic mixing valve is recommende • Water Supply: d for Single inlet cold or pre-mixed – a TMV2 plated brass finishes or available • Quality polished chrome plated brass or lacquered nickel contamination • Touch Free Tap – for ultimate hygiene – prevents cross DB 200 / DB 225 Dolphin Blue Infrared Tap page 12 WP 208R page 105 WP 112R 01424 202224 page 159 BC 2006 • Powered by 9v plug in transformer • Powered by 6 DB 225S x AAA / 9v PP3 battery DB 200S (designed to match brushed stainless steel) Brushed nickel finish • Powered by 9v plug in transformer • Powered by 6 x AAA / 9v PP3 battery Polished chrome finish Product Codes DB 225C DB 200C page 190-191 low battery warning) – for other power source options see • Power: Plug-in 9 volt transformers or 9 volt battery (with • 3/8" BSP water supply connector • Counter hole Ø 28-34mm Min-max thickness 2-27mm • Power Connections: tap male, power source female • Projection 105mm • H 142 x Ø 45 mm Product Data paoS sresnepsiD source Power Ø50 Ø45 001 135° Counter Mounte d 241 eussiT telioT lew oT repaP noitani resnepsiD bmoC dnaH riA t resnepsiD oH stinU sreyrD spaT sniB moorhsaW seirosseccA page 178 DB 200 105 Taps Bellchem WD9 174-269 taps, bins, access.qxd :Layout 1 DOLPHIN Request your 200 page catalogue today on BC 634 Dolphin Behind Mirror Soap Dispenser Spare parts can be obtained only by ordering the relevant kit. Spare parts cannot be ordered individually. In order to locate the relevant spare part, please check the corresponding part and part number at the drawing at the last page. When ordering spare parts (kits) please mention the corresponding catalog number (Cat. No.). Quantity Part Number Description Cat. No. - Soap Dispenser Spout Kit BC 07271023 1 6 Spout BC 07015068 1 7 Support BC 07120273 1 8 Nut BC 07099088 1 9 Nipple BC 07025276 1 10 O-ring BC 04540061 - Sensor Kit BC 07220230 1 1 Electronic Unit BC 08002150 1 2 O-ring BC 04510193 3 Soap Tank 1L BC 07100020 4 Pump Soap Dispenser BC 07222001 5 Bottle 1L support BC 07120175 11 Transformer BC 06522042 Haywood Way, Ivyhouse Ind Est, Hastings, TN35 4PL [email protected] www.dolphindispensers.co.uk DOLPHIN Southpoint, Compass Park, Bodiam, Robertsbridge TN32 5BS [email protected] www.dolphindispensers.co.uk DOLPHIN Dolphin Blue INFRARED SYSTEMS IMPORTANT DESIGN TIPS Dolphin Blue Infrared Systems DESIGNING A WASHROOM INCLUDING DOLPHIN BLUE INFRARED SYSTEMS Dolphin Blue Infrared Taps, Shower Controls and Urinal Flush Valves offer significant water and energy savings. However, there are some simple DO’s and DON’Ts and TIPs which will help avoid 99% of the situations often associated with infrared systems for washrooms. It should be noted that these details are not exhaustive but will help eliminate 99% of situations. It is recommended that for larger projects especially where design restraints will result in taps being set on minimum or maximum settings, we would advise a very simple mock-up be set with materials to be used to ensure infrared device operates as desired. DO’s BATTERY BACK UP PRESSURE DO include a battery back-up device when installing a transformer powered infrared tap in an accessible washroom. DO ensure the static and dynamic pressure at the Dolphin Blue device is within the tolerances stated on the product literature / data sheet (please ask if you cannot find it). Most devices are tested to operate between 0.5 and 8 bar. If pressures are outside the stated tolerances please contact the Technical Helpline on 01424 20 22 24. SECURITY TIME DO ensure security time is set at approximately 20 seconds on infrared taps especially in locations susceptible to vandalism. Also important: to be set at 20 seconds to comply with ECA/WTL scheme. FLOW RATE DO specify what flow rate is required when placing your order. Taps – 6 litre / minute is standard. 4 litre / minute is readily available. FILTERS Do ensure filters supplied with the Dolphin Blue device are installed. It may not be sufficient to rely on the filters often included with thermostatic mixing valves as the gauge of the filter mesh may not be fine enough. It is also important to ensure pipes are flushed prior to connection and filters are inspected on a regular basis. Time between inspections will depend on hardness and quality of water. Shower head – 9 litres/ minute is standard, 8 litres / minute is available. DISTANCE FROM TRANSFORMER Please speak to the Dolphin Technical Helpline for other flow rates if required. It is recommended you ensure the maximum distance between a Dolphin Blue Infrared Tap and its power source is 5 metres. DON’Ts M IRRORS PANEL MOUNTED INFRARED TAPS It is not advisable to locate a Dolphin Blue Infrared device directly opposite a mirror where the infrared eye faces the mirror in such a way that it could reflect itself as this can cause false activations even if the mirror is 2-4 metres away from the infrared eye. It is very important to ensure the distance between the sensor and the bottom of basin when installing a panel mounted Dolphin Blue Tap with an integral sensor is a minimum of 300mm above the bottom of the basin. TWO INFRARED TAPS Minimum 300mm distance critical It is not advisable to locate infrared taps directly opposite each other where the infrared eyes face each other as this can also cause false activations even when there is a fair distance between them. TIPs POLISHED TRAPS AND SINK SURFACES When installing a Dolphin Blue Panel Mounted Tap with an integral sensor it is recommended that you avoid a highly polished chrome trap or sink surface – it will act like a mirror to the tap sensor, potentially causing false activations and wasted water Avoid polished/ chrome strainers HIGH VISIBILITY CLOTHING It is a feature of most infrared devices in the washroom market that the reflective strips on high visibility clothing may cause the device to operate, even if someone just walks past, with no intention of using it. The DB51 Dolphin Blue Remote Control can be used to reduce the range of a device to reduce these false activations but may not eliminate the phenomena completely. ‘TALL’ VERSION TAPS AND SPOUT LENGTHS Consider the position of the water outlet / aerator in relation to the basin. Please feel free to discuss spout lengths with the Dolphin Technical Helpline on 01424 20 22 24. March 2017 It’s a Dolphin thing Dolphin Solutions Ltd Southpoint, Compass Park, Bodiam, Robertsbridge, TN32 5BS Tel: +44 (0)1424 20 22 24 Fax: +44 (0)1424 205 200 [email protected] www.dolphinsolutions.co.uk S O U T H PO I N T, CO M PA S S PARK, B O DI A M , RO B E RTS B R I DG E , T N 3 2 5 B ST, U N I T E D K I N G D OM + 44 (0)1424 202 224 TEL + 44 (0)1424 205 200 FA X h e l l o @ d o l p i n so l u t i o n s.c o .u k d o l p h i n so l u t i o n s.c o .u k